Qstarz BT-Q1000eX User manual

GPS Lap Timer 10Hz English
……………………………………………………………………………………………………………………………………………………………………………………….
……………………………………………………………………………………………………………………………………………………………………………………….
www.Qstarz .com 1
BT-Q1000eX 10Hz Quick Installation Guide
A. Standard Package
GPS Unit BT-Q1000eX 10Hz (1) + Lithium-ION Rechargeable Battery
(2) + Cigarette Adapter (3) + mini USB Cable (4) + Driver CD (5) +
Leather Bag (6) + Warranty Card + User’s manual
NOTE: The Cigarette Adaptor can only be used to charge
BT-Q1000eX. Please don’t make use of it with devices other
than BT-Q1000eX.
1. 2. 3.
4. 5. 6.
B. Appearance
1. Power jack (mini USB type)
2. Mode switch (OFF/1Hz/10Hz)
3. Battery status LED (Red/Green)
4. Bluetooth status LED (Blue)
5. GPS status LED (Orange) /
Log Status LED (Red)
6. Internal antenna
7. POI button

English
……………………………………………………………………………………………………………………………………………………………………………………….
.........................................................................................................................................................................................
2 www.Qstarz.com
C. LED Indicators
LED Status Flash ON OFF
Power
(Red/Green) Low Power (Red) Recharging
(Green)
Fully
charged
Bluetooth
(Blue)
Flash per 2 sec.:
Bluetooth connected
and transmitting
Mode
Flash per 5 sec.:
Power saving mode
Not
connected /
Pairing / Log
Mode is on
(1Hz mode)
GPS not
powered /
Log Mode is
on (10Hz
mode)
GPS
(Orange)
GPS position is fixed,
Navigation
Detecting
Satellite,
GPS position
not fix
GPS not
powered
Log
(Red)
Flash per 2 sec: Low
memory (20%)
Flash 3 times:
POI(Point of Interest)
is recorded
Memory is
full
Log Mode
is off
D. Beeper Code
*Beeper can be turned off from software -> config GPS.
Status Beep code Description
Startup 1 short beep One short beep on off->1Hz,
Off->10Hz, 1Hz->10Hz, or 10Hz->1Hz
GPS fix 2 short beeps 2 short beeps when GPS fix on 1Hz
or 10Hz mode
POI button 3 short beeps 3 short beeps when POI button
being pressed
Memory
exhausted 3 long beeps 3 long beeps when the device is out of memory
Sleep mode 1 long and 1 1 long and then 1 short beep when

GPS Lap Timer 10Hz English
……………………………………………………………………………………………………………………………………………………………………………………….
……………………………………………………………………………………………………………………………………………………………………………………….
www.Qstarz .com 3
short beeps the device enters sleep mode
E. Register your Qstarz product
Register your Qstarz product to get the latest news,
software update, event, and product information.
http://www.qstarz.com/reg.php
Update the Software:
Please always go to Qstarz download page to check if there
is any latest software update.
http://www.qstarz.com/download.php
Start to use
Step 1: Install Battery
Open the Battery Cover and Insert the Battery.

English
……………………………………………………………………………………………………………………………………………………………………………………….
.........................................................................................................................................................................................
4 www.Qstarz.com
Step 2: Charge Battery
Plug in USB cable and charge it for 3 hrs until
the green power LED goes off.

GPS Lap Timer 10Hz English
……………………………………………………………………………………………………………………………………………………………………………………….
……………………………………………………………………………………………………………………………………………………………………………………….
www.Qstarz .com 5
Step 3: Mount Q1000eX 10Hz - 1
Mount Q1000eX on your eXtreme sports
equipment.
1. 2. 3.
4. 5. 6.

English
……………………………………………………………………………………………………………………………………………………………………………………….
.........................................................................................................................................................................................
6 www.Qstarz.com
Step 3: Mount Q1000eX 10Hz - 2
To get best accuracy, please position the GPS
antenna side up to sky.
Caution: To reduce the risk of fire or
shock hazard, do not expose this
product to rain or moisture. If the
device will be exposed to outside
environment, such as attached on
motorcycle, any other safety
protection equipment must be applied
to prevent the device from sliding out
of the bag.

GPS Lap Timer 10Hz English
……………………………………………………………………………………………………………………………………………………………………………………….
……………………………………………………………………………………………………………………………………………………………………………………….
www.Qstarz .com 7
Step 4: Start Racing
Note: Q1000eX is for outdoor use; an open sky
outdoor environment will enable faster satellite
acquisition and provide better positioning
accuracy.
1. Switch Q1000eX to 10Hz mode
2. Confirm GPS gets fix
3. Start to Race
2 short
beeps
GPS LED
flashes

English
……………………………………………………………………………………………………………………………………………………………………………………….
.........................................................................................................................................................................................
8 www.Qstarz.com
Step 5: Install Qstarz QRacing
Software
Install the QRacing from Qstarz software CD.
You may also install PC Suite software (QSports
and QTarvel) for manage other sports activity or
geotagging your travel photos.
Note: Users have to input product key at the
first time of use. The product key is located on
the envelope of the software CD

GPS Lap Timer 10Hz English
……………………………………………………………………………………………………………………………………………………………………………………….
……………………………………………………………………………………………………………………………………………………………………………………….
www.Qstarz .com 9
Step 6: Import Data from
Q1000eX 10Hz
1. Switch on and Connect to PC, then open
QRacing
2. QRacing will automatically detect the device
and ask if you want to read log from device.

English
……………………………………………………………………………………………………………………………………………………………………………………….
.........................................................................................................................................................................................
10 www.Qstarz.com
3. Click on “Yes” to import the data and Select
your Racing Type.
Step 7: Edit Beacon
After import data from Q1000eX, if you have not
edited beacons for this track, QRacing will ask
you to edit beacons.