Quadrone Pro User manual

• Four axis structure makes the quadcopter for flexible and faster for flying.

•It is wind resistant and can be flown indoor and outdoor.

• Built in 6 axis gyroscope for precise hovering in the sky.

• Simple design makes changing parts easy.

• Comes with 360 degree flips and throwing take off features.

The materials and specifications mentioned in this manual or the parts in this package are for reference only.

Key features of quadrone

AWW INDUSTRIES™ is an innovative division of DGL Group, Ltd.

Other trademarks and trade names are those of their respective owners.

AWW INDUSTRIES,

195 Raritan Center Parkway, Edison, NJ 08837.

WARNING: This product may

contain a chemical known to

the State of California to cause

cancer, or birth defects, or

other reproductive harm.

PROP 65 WARNING Tested to comply with FCC standards.

FOR HOME OR OFFICE USE.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful

interference and

(2) This device must accept any interference

received, including interference that may

cause undesired operation.

Manufactured in China.

Batch Ref: XXXX

Model Number: XXXX

Specifications, colors and contents may vary from illustrations.

CAUTION: Adult assembly required due to small parts and sharp edges.

Keep out of reach from children and dispose of unused parts and wrappings responsibly.

BATTERY WARNING:

• Do no mix alkaline, standard (carbon zinc), rechargeable (nickel hydride) batteries.

• Do not mix old and new batteries.

• Non-rechargeable batteries should not be recharged.

• Rechargeable batteries should be removed from the appliance before being charged.

• Rechargeable batteries should be charged under adult supervision only.

• Exhausted batteries should be removed.

• The supply terminals should not be short-circuited.

• Only batteries of the same or equivalent type are recommended to be used.

• Batteries should be inserted with the correct polarity.

IMPORTANT INSTRUCTIONS

1. This product is precise equipment that integrates mechanics and electronics with expertise in aerodynamics and

high-frequency transmitting. It is required for the quadcopter to be correctly assembled and debugged to prevent an

accident to occur. The owner of this product should control the quadcopter safely and carefully. Please keep in mind we are

not responsible for this product being used improperly. This may result in severe injury or loss of property and we can not

control the operating process once the user assembles or uses this product.

2. This product is suitable for ages 14 years and up and people who have operating experience in flying a model.

3. Please fly quadcopter in open areas such as a local field and areas that allow remote control flying.

4. Once you are the owner of this product, you are responsible for your actions.

5. If there are any problems while using this product, such as operating or repairing, please reach our sales agent for

details. The sales agent will provide you with the technical support and after-sale service.

REMOTE CONTROLLER DIAGRAM

1. Use a screwdriver to remove screw on the back of

the transmitter, then open the battery cover (Figure 1)

2. Install 4 “AA” batteries (not included) into the back

of the transmitter then replace the battery cover and

reinstall the screw (Figure 2).

1. Install batteries with correct polarity.

2. Do not mix old and new batteries.

3. Do not mix different types of batteries.

Antenna

High/Low

speed switch

Indicator

Flip mode

Forward/backward trim

Fight control lever

(Directional)

LCD display

Mode switch

Sideward fine-tuning (Mode 1)

Turning fine-tuning (Mode 2)

Left control lever

(Accelerator)

Photo and video

Power ON/OFF

Turning fine-tuning (Mode 1)

Sideward fine-tuning (Mode 2)

1. Sideways fine-tuning (Turn left/right fine-tuning in Mode 2)

2. Forward/backward fine-tuning

3. Turn left/right fine-tuning (Sideways fine-tuning in Mode 2)

4. Throttle power

5. Forward speed

6. Backwards speed

7. Right sideways speed

8. Left sideways speed

9. Left turning speed (The higher the level, the faster it will turn)

10. Right turning speed (The higher the level, the faster it will turn)

11. High/Low speed: Hold the “A” button to switch between high speed mode and low speed mode. “H” means high

speed and “L” means low speed.

12. Power indicator: Shows the remotes battery life

13. Mode indicator: Mode 1 is the default mode when powered on. To change to Mode 2, hold the “B” button, then re-turn

on the remote. The Mode on the LCD display will now be changed.

14. Signal power

Step 1: Switch the On/Off switch to ON. Step 2: Open the battery cover and insert

the battery into the power port.

Step 4: Push the throttle lever to the

highest position, then push it to its lowest.

There will be a beep from the remote,

indicating the quadcopter is in pre-flight

mode.

Step 3: Close the battery cover and turn on

the quadcopter.

Step 1: Push the On/Off switch of the

quadcopter to the OFF position and then

open the battery cover.

Step 2: Pull the battery wire out of the

power port.

Step 3: Insert the battery power port to the USB

charging cable. A light will turn on to indicate it is

powering.

GETTING READY TO FLY

CHARGING YOUR BATTERY

CAUTIONS WHEN CHARGING

1. Please keep this product in a dry, ventilated area away from any heat source or explosive product.

2. Please remove the battery from the quadcopter. Only charge under the supervision of an adult.

3. After flying, do not charge the battery until the battery has cooled down in order to avoid a swollen battery and

a fire hazard.

4. Please use the provided USB charging cable to avoid damaging the battery.

5. When not used for a long time, a battery can lose its charge. Avoid charging too often to maximize battery life.

1. Install the landing skids to the bottom of the quadcopter, then lock screws (Figure 1).

2. Install the blade protecting frame to every corner, then lock screws (Figure 2).

The remote features two built in modes, Mode 1 and

Mode 2. To change modes, flip the “B” button and then

restart the remote.

Operation Instructions

Push the throttle up or down to make the quadcopter

fly up or down

Push the direction lever up or down to make the

quadcopter fly forward or backward.

Push the throttle left or right to make the

quadcopter turn left or right.

Push the direction lever left or right to make the

quadcopter fly to the left side or the right side.

MODE 1

Sideward flying

Forward and backward

Turn left and right

Hover up and down

Operation Instructions

Push the throttle up or down to make the quadcopter

fly up or down

When the quadcopter unintentionally

flies forward/backward, press the

fine tuning button up or down until

the problem is corrected.

When the quadcopter unintentionally

flies to the left/right side, press the

fine tuning button left or right until the

problem is corrected.

When the quadcopter unintentionally

turns to the left/right side, press the

fine tuning button left or right until the

problem is corrected.

Push the direction lever up or down to make the

quadcopter fly forward or backward.

Push the throttle left or right to make the

quadcopter turn left or right.

Push the direction lever left or right to make the

quadcopter fly to the left side or the right side.

MODE 2

Sideward flying

Forward and backward

Turn left and right

Hover up and down

Forward/backward fine-tuning Sideward fine-tuning Turn left/right fine-tuning

When the quadcopter unintentionally flies

forward/backward, press the fine tuning

button up or down until the problem is

corrected.

When the quadcopter unintentionally flies

to the left/right side, press the fine tuning

button left or right until the problem is

corrected.

When the quadcopter unintentionally turns

to the left/right side, press the fine tuning

button left or right until the problem is

corrected.

Low-Voltage Protection:

When the quadcopter battery is low, the power supply to the rotors will stop automatically

Power Surge Protection:

When the quadcopter rotating blades becomes jammed, the control system will stop supplying power to the rotors

automatically. Please then rematch the signal to fly again.

Restart function:

In case of flight disorder, restore remote to the factory default settings using the following method.

When the quadcopter’s

lights go from flashing

quickly to flashing slowly,

push the throttle lever to its

highest position, then pull it

back to its lowest. The

quadcopter’s lights should

then change from flashing

to staying on.

Place the quadcopter on a flat surface and

push both the remotes left and right levers to

the lowest right corner and hold for 2-3

seconds. The lights on the quadcopter will

change from normal to flashing quickly. After

the 2-3 seconds, when the lights change back

to normal, it means the quadcopter has

successfully been reset.

Throwing Flight Instructions

Thanks to a 6 axis gyroscope, you can throw your quadcopter

and push up the throttle and it will automatically level our and

hover smoothly even though it is tumbling through the air.

Once you’re familiar with basic flying, you can try some awesome and exciting tricks and

stunts! First, fly the quadcopter to a height of about 10 feet, then press the 3D eversion

switch on the back right side of the remote. Now push the right lever in any direction and

make it do a 360 flip!

1. Push the camera into the slot on the battery cover (Figure 1).

2. Open the battery cover with the camera attached (Figure 2).

3. Lock in screws to secure camera to cover (Figure 3).

4. Close the battery cover with the camera, then insert the 3-pin plug to the slot on the side the quadcopter (Figure 4).

Getting Started:

1. Make sure the 3-pin plug of the camera is plugged into the quadcopter.

2. Turn the quadcopter on. The camera’s light will go from red, to flashing green, to green. If the light is red

and then turns off seconds later, it means the SD card is not in the camera. Insert the SD card and the light

will turn green.

Taking Photos or Video:

1. Turn on the remote, push the left lever up and down to connect the quadcopter and remote.

2. Take a photo: When pushing the “C” switch up, the camera will take a photo after a beep from the remote.

The green light on the camera with flash and turn red.

3. Take a video: When pushing the “C” switch down, the camera will begin to take a video after a beep from

the remote. The green light will change to a flashing red. Slightly press the “C” switch again to stop taking

video. The red flashing light will return to green.

Tips: 3D flips work best with a fully charged battery.

INSTALLING THE CAMERA (Optional Add-on)

BATTERY WARNING:

• Do no mix alkaline, standard (carbon zinc), rechargeable (nickel hydride) batteries.

• Do not mix old and new batteries.

• Non-rechargeable batteries should not be recharged.

• Rechargeable batteries should be removed from the appliance before being charged.

• Rechargeable batteries should be charged under adult supervision only.

• Exhausted batteries should be removed.

• The supply terminals should not be short-circuited.

• Only batteries of the same or equivalent type are recommended to be used.

• Batteries should be inserted with the correct polarity.