Qualitel C33R User manual

C33R Repeater
User manual

Getting to know your Repeater
LED INDICATOR STATUS:
Off = Power supply is off Blue (Double flash) = Repeater in use with good signal
Red/Blue = In registration mode Purple (Steady) = Weak link to telephone base station
Blue (Triple flash) = Registration completed successfully Purple (Double flash) = Repeater in use with weak link
to base station
Blue (Steady) = Good link to telephone base station Red (Steady) = No link to telephone base station

Setting up
Connect the mains power adaptor
Plug the small end of the power adaptor cable into the socket on the back of the Repeater.
Then plug the other end into the mains wall socket but don’t switch the power on at the wall socket yet.
Use a power socket close to your telephone base station. This is because during the registration process, the telephone base
station needs to be near the Repeater. You can relocate your Repeater after registration is complete.
Warning
Only use the power adaptor supplied otherwise your product may not work and you could damage the product.

Automatic registration to the telephone base station
1. Before beginning registration, make sure that all unregistered Repeaters are switched off.
2. Turn on the Repeater mode in the telephone base station that you will be registering the Repeater to. This varies dependant on
the product, the instruction can be found in the User guide, provided with the telephone base station.
3. Put the telephone base station into registration mode, this is normally done by pressing and holding the Find button, but again
consult the User guide, provided with the base station.
4. Switch on the power to the Repeater at the wall socket and the Repeater will register automatically. The LED on the Repeater will
toggle between Red and Blue, followed by a triple blue flash to confirm that registration is complete. The LED will remain blue to
indicate that the registration is complete.
5. You can now safely disconnect the power and move the Repeater to your selected location. The Repeater will remain registered
to the telephone base station.
NOTE: If the LED continues to flash red, try registering the Repeater again.

Manual registration (optional)
You can also register the Repeater manually if you prefer.
1. Before beginning registration, make sure that all unregistered Repeaters are switched off.
2. Turn on the Repeater mode in the telephone base station that you will be registering the Repeater to. This varies dependant on
the product, the instruction can be found in the User guide, provided with the telephone base station.
3. Switch on the power to the Repeater at the wall socket.
4. Press and hold the button for 5 seconds. the Repeater will start registering to the base station. The LED on the Repeater will
toggle between Red and Blue, followed by a triple blue flash to confirm that registration is complete. The LED will remain blue to
indicate that the registration is complete.

Wall mounting the Repeater (optional)
The unit may be left free standing or mounted on a wall. See diagram below for reference only. The screws should be fixed at 92mm
apart horizontally.
WARNING
QUALITEL TRANSMISSION recommends that you seek advice from a building professional before attempting to wall mount your
Repeater. QUALITEL TRANSMISSION is not responsible for any damage/injury caused while attempting to wall mount your
Repeater.
Before you wall mount, please check that:
• The wall can support the weight of the Repeater;
• You are not drilling into any hidden wiring or pipes;
• The power cable will reach the wall socket.
The diagram above is for reference only. It is not a template to scale.

Using your QUALITEL DECT Repeater
Location tips:
• place as high as possible, at least 1.8
meters off the ground
• place 1 meter from sources of electrical
interference such as hi-fi systems, office
equipment microwaves, computers and
routers
• avoid heat sources and direct sunlight
• avoid things that can interfere with radio
signals such as metal doors, thick walls
and cupboards
• If extending the range to outdoors locate
the Repeater near a window and higher on
the wall, as radio signals do not work as
well through thick walls
• If using more than one Repeater on a
telephone base station ensure the
Repeaters are placed at least 10 meters
apart
• Do not use outdoors
Once registered, the Repeater can be positioned anywhere within the reception
range of the telephone base station, preferably towards the direction you wish to
extend the range.
1. Locate a suitable position near a mains socket within the reception area of the
telephone base station and towards the direction you wish to extend the range.
2. Plug the power adaptor into the mains socket (and into the Repeater if it has
been disconnected) and switch on the mains power at the wall socket.
The blue LED will begin to flash as it connects to the telephone base station, then
stops flashing and remains lit once a link has been made. If the LED continues to
flash, switch the power off and on again. If flashing continues, see the ‘Help’
section on page 10.
Operating a handset for the first time within the extended
Repeater area
Make sure that multiple handset(s) has been registered to the same telephone
base station as the Repeater.

1. Switch off the handset within the new reception range of the Repeater but
outside the reception range of the telephone base station, and then switch it
back on again.
2. To confirm the handset is working with the Repeater, press the Talk button
on the handset whilst next to the Repeater. You should hear dial tone. Look at
the Repeater, the blue LED should be flashing.
Your Repeater is now ready for use.
To de-register/reset the Repeater
You can de-register the Repeater and then register it to another telephone
base station if you wish to.
1. Switch the power to the Repeater off at the wall socket.
2. Press and hold the Setup button, then switch the power back on keeping
hold of the button for 5 seconds. The Repeater will now be de-registered.
Please note
Blind spots (where signal is weak) can cause
loss of signal. Avoiding blind spots will
reduce the risk of losing a call.

Help
The Repeater LED continues to flash on and off after the registration process has been completed
• The registration process was not successful. You will have to repeat the registration process again with the telephone base station
concerned. De-register the Repeater, see page 9 and register it to the base station again, see page 5.
The Repeater LED continually flashes on and off when placed/mounted in the desired location
• The radio connection is very weak/poor. You will have to find another location where the signal from the telephone base station is
better.
• The Repeater may have been reset. If this is the case it will have to be registered to the telephone base station again.
The Repeater LED does not light up at all
• There is no power to the Repeater. Check that the power adaptor lead is plugged into the Repeater, the power adaptor is plugged
into the mains socket and the mains power is switched on.
The audio quality is very poor/noisy when in the Repeater reception area
• The radio connection is very weak/poor. You will have to find another location where the signal from the telephone base station is
better.
• Move the Repeater closer to the telephone base station.
• Make sure the Repeater is not too close to metal objects or thick walls.
• Check for interference from electronic devices.

The Repeater will not register
• Reset the Repeater as described on page 9.
Cannot make or receive calls when in the Repeater reception range
• There is no power to the Repeater. Check that the Power adaptor cable is plugged into the Repeater, the power adaptor is plugged
into the mains socket and the mains power is switched on.
• Make sure there is at least 10 meters between Repeaters.
• The Repeater is not registered. You will have to repeat the registration process again with the telephone base station concerned.
Call lost or audio becomes poor when moving from the telephone base station reception area to the
Repeater reception area
• You may be moving out of range of the telephone base station/Repeater areas, or are in a ‘blind spot’. Move towards the telephone
base station or Repeater.
• Some telephone base stations and handset combinations do not support call handover during conversation when moving from
telephone base station to Repeater area.

General information
Safety
General
• Only use the power supply included with the product. Using
an unauthorized
power supply will invalidate your guarantee
and may damage the product.
• Do not open the Repeater. This could expose you to high
voltages or other risks. Contact the QUALITEL DECT Repeater
Helpline on [phone] for all repairs.
• The QUALITEL DECT Repeater operates by transmitting
radio signals. These signals may cause interference to hearing
aids.
• It is recommended that advice from a qualified expert be
sought before using this product in the vicinity of
emergency/intensive care medical equipment.
• It is recommended that if you have a pacemaker fitted you
should check with a medical expert before using this product.
• Your product may interfere with other electrical equipment,
e.g. TV and radio sets, clock/alarms and computers if placed
too close. It is recommended that you place your product at
least one meter away from such appliances to minimize any
risk of interference.
Cleaning
Simply clean the product with a damp (not wet) cloth, or an
anti-static wipe. Do not use a dry cloth as it could cause a
static discharge resulting in damage to the product.
Environmental
• The QUALITEL DECT Repeater will produce a certain
amount of heat during operation. Equally, additional
handsets and the chargers can become warm during
charging. Whilst this is entirely safe, we advise against
placing these products on antique, veneered
or wooden
surfaces as damage may occur.
• Do not stand your product on carpets or other surfaces
which generate fibres, or place it in locations preventing free
flow of air over its surfaces.

• Do not use the QUALITEL DECT Repeater and handsets in
damp, humid conditions such as bathrooms. Do not expose
any of the equipment or batteries to fire or water.
Product disposal instructions
The symbol shown here and on the product
means that the product is classed as Electrical
or Electronic Equipment and should not be
disposed with other household or commercial waste at the end
of its working life.
The Waste of Electrical and Electronic Equipment (WEEE)
Directive (2002/96/EC) has been put in place
to recycle
products using best available recovery and recycling
techniques to minimize the impact on the environment, treat
any hazardous substances and avoid the increasing landfill.
Product disposal instructions for residential users
When you have no further use for it, dispose of the product as
per your local authority’s recycling processes.
For more
information please contact your local authority or the retailer
where the product was purchased.
Product disposal instructions for business users
Business users should contact their suppliers and check the
terms and conditions of the purchase contract and ensure
that this product is not mixed with other commercial waste for
disposal.
R&TTE Directive
Hereby, QUALITEL declares that this QUALITEL DECT
Repeater is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
For a copy of the Declaration of Conformity please visit
www.qualitel.co.za
Guarantee
Your QUALITEL DECT Repeater is guaranteed for a period
of 6 months from the date of purchase. Subject to the terms
listed below the guarantee will provide for the repair of, or at
QUALITEL’s or its agent’s discretion the option to replace
the QUALITEL DECT Repeater, or any components thereof,
which is identified as faulty or below standard, or as a result
of inferior workmanship or materials.

The conditions of this guarantee are:
• The guarantee shall only apply to defects that occur within the
6 month guarantee period.
• Proof of purchase is required.
• The equipment is returned to QUALITEL or its agent as
instructed.
• This guarantee does not cover any faults or defects caused
by accidents, misuse, fair wear and tear, neglect, tampering
with the equipment, or any
attempt at adjustment or repair
other than through approved agents. The guarantee does not
cover damage caused by misuse or damage caused by
over-voltage as a result of faults on the power line or damage
caused by lightning.
• This guarantee does not affect your statutory rights.
Within the 6 month guarantee period:
If you experience difficulty using the product, prior to returning
it, please read the ‘Help’ section beginning on page 10, or
contact the QUALITEL DECT Repeater Helpline for assistance
on phone [phone].