Quark-Elec QK-A016 User manual

V1.0(04/21)
QK-A016
Disclaimer: This product is designed to aid navigaon and should be used to augment normal navigaonal procedures
and pracces. It is the user’s responsibility to use this product prudently. Neither Quark-elec, nor their distributors or
dealers accept responsibility or liability either to the product user or their estate for any accident, loss, injury or
damage whatsoever arising out of the use or of liability to use this product.
empty or full capacity to start the monitoring process.
Quark-elec recommend starng at full (aer the baery has been fully charged) unless you are
unsure of the capacity of the baery. In this case the capacity (CAP) and High voltage (HIGH V)
need to be setup. The capacity can be found on the specicaons of the baery, this should
normally be listed on the baery. The high voltage can be read from the screen aer fully
charged.
If you are unsure of the baery capacity, then you can start with the baery fully depleted
(empty). Check the voltage shown on the screen and set this as the low voltage (LOW V). Then
set the monitor to its highest capacity (e.g. 999Ah). Aerwards please charge the baery fully
and record the capacity when charging is complete. Enter the Ah reading for capacity (CAP).
You can also setup the alarm level to receive audible alerts. When the state-of-charge capacity
has fallen below the set value, the percentage and baery symbol will ash, and the buzzer will
begin beeping every 10 seconds.
Setup process
1.Press and hold the OK key on the faceplate unl the set-
up screen appears. This will show the four parameters
needed to be entered.
2.Press the up(▲) or down(▼) keys to move the cursor to
the seng you would like to change.
3.Press the OK key to select the parameters for seng.
4.Press the up or down arrow keys again to select the proper value applied.
5.Press the OK key to save your sengs and then press le(◄) key to exit the current sengs.
6.Press the le(◄) key again, the display will exit the set-up screen and back to the normal
working screen.
* Setup HIGH V or LOW V only, don’t set both values unless you clearly know the voltage
characteriscs of the baery.
NMEA 0183 OUTPUT
The A016 outputs the real me voltage, current, and capacity (in percent) via the NMEA 0183
output. This raw data can be monitored using any serial port monitor soware or apps on mobile
devices. Alternavely, apps such as OceanCross can be used to view the end user informaon.
The output sentence format is shown below:
Example:
$IIXDR,U,12.10,V,A016,*CS ----the current voltage is 12.1V
$IIXDR,I,2.1,A,A016,*CS ----the present current is 2.1Amp
$IIXDR,G,64.0,%,A016,*CS ----the current capacity( remaining) is 64.0%
SET-UP GUIDE
QK-A016 BATTERY MONITOR
MEASURE STATE OF CHARGE
WITH NMEA 0183 OUTPUT
All products are CE, RoHS cered
www.quark-elec.com
Please recycle your packaging

QK-A016
BEFORE STARTING INSTALLATION:
Ensure that no metal tool can cause a short circuit. Removing all jewellery such as rings or
necklaces prior to any electrical work is considered best pracce. If you believe you may not be
suciently skilled to undertake this installaon safely, please seek the assistance of an installer/
electrician who is aware of regulaons for working with baeries.
• Please strictly follow the order of connecons given below.
• Use a fuse of the correct value as shown in the following diagram.
INSTALLATION
1. Determine a mounng locaon and mount the shunt. The shunt should be installed in a dry
and clean place.
2. Remove all loads and charging sources from the baery before any other steps are taken. This
is oen accomplished by turning o a baery switch. If there are loads or chargers directly
aached to the baery, they should be disconnected as well.
3. Serial connect the shunt and the negave terminal of the baery (the blue wires shown on the
wiring drawing).
4. Connect B+ of the shunt to the posive terminal of the baery with a AGW22/18 wire (0.3 to
0.8mm²).
5. Connect the posive load to the posive terminal of the baery (using a fuse is highly
recommended).
6. Connect the posive charger terminal to the posive terminal of the baery.
7. Connect the display to the shunt with the shielded wire.
8. Double check all the connecons with the above diagram before turning on the baery switch.
At this point the display will power up, and be
operaonal in a few seconds.
The A016’s display comes with a buckled enclosure.
A 57*94mm’s rectangular slot needs to be cut for
ng.
QK-A016
DISPLAY AND CONTROL PANEL
The display shows the state-of-charge on the screen. The following image provides what the
displayed values indicate:
Remaining capacity
percentage
Baery sym-
Real voltage Real current Real power
Time-to-go
Remaining capacity
(Amp-hours)
Remaining capacity percentage: This shows the percentage of the actual full-charge capacity of
the baery. 0% indicates empty while 100% means full.
Remaining capacity in Amp-hours: The remaining capacity of the baery.
Real voltage: Displays of the real voltage level of the baery.
Real current: The current display informs of the current load or charge of the baery. The display
shows the instantaneously measured current rate owing out of the baery. If the current ows
into the baery, the display will show a posive current value. If the current ows out of the
baery, it is negave, and the value will be shown with a preceding negave symbol (i.e -4.0).
Real power: The power rate being consumed whilst discharging or supplied whilst charging.
Time-to-go: Shows an esmate of how long the baery will sustain a load. Indicates the me
remaining unl baery is completely discharged when the baery is discharging. The remaining
me will be calculated from the residual capacity and the real current.
Baery symbol: When the baery is being charged it will cycle to show it is lling. When the
baery is full the symbol will be shaded.
SETUP
Setup baery monitor parameters
The rst me you use your A016, you will need to set the baery to its starng point at either