Quattro RazorLED RAZ-WR96 Technical document

B Bulbs
,
.
Important: Read all i nstructi ons pri or to i nstallati on
Wir l ss nuattra 'I Za n Him m r
12-36vdc LED Wall+Mini Remote Control
•
Parts Included
1- 4 Zone Wall Dimmer Control
(or use as mini touchpadremote)
1-CR2032LongLifeBattery
1- Installation Instructions
Wall Buttons
ButtonActions: On/Off/Dimming Functions
Specification Sheet
Part Number VLRZ-RAZ-
Q4RF
Receiver: VLRZ-RAZ-WR96
VLRZ-RAZ-Q4RF LED Dimmer Wall Switch
Operating Voltage Operating Frequency
3VDC 434 MHz/868 MHz
VLRZ-RAZ-WR96 LED Rece i ver
Input Voltage Current Output Voltage
1 X(1 2-36)VDC l XBA 1 X(96-288)W
Left 6 Right Buttons
All Zones
Left 6 Right Buttons
All Zones
Single push of Left zone button turns lights oninpair zone(s).
Single push of Right zone buttonturns lights off inpair zone(s).
Press and holdLeftzone button to increase brightness.
Press and hold Right zone buttonto decrease brightness. Safety
Remote needs to be in range of receivers. Average range is
100". Range will decrease as battery power gets low.
DO NOT expose the remote or controller to direct or indirect moisture
Pairing Instructions:
After you have wired all the receivers according to your project requirements, do the
f o l l o w i n g :
1. If you use multiple receivers, you have two choices: (1) Have all the receivers in the same zone,
like zone 1for example, or (2) have each receiver(s) in a different zone, like Zone 1, 2, 3 or 4.
2. In order for each receiver to know what Zone it belongs to, you will need to “pair" it to the zone you
wish to use. In order to do this, you need to power up the unit with the LED lights hooked to it. Then
reset the receiver by pressing and holding the "Learning”button until the lights blink 2 times. To "pair"
you need to quickly and firmly press and release the "Learning" button on the receiver, and
immediately after that you will need to quickly press and release the ON or OFF button on the
RAZ-Q4RF control for the zone you wish to use. Once you do that, the lights will blink once. Now your
Remote and Receiver are paired.
3. Do the same for any other receivers if you use them.
Set-Up Instructions
Outlet Power Supply Receiver
LEDStrip
-'(j- Smart
NOTE: Resetthe receiver by pressing andholding the "Learning" button untilthe lights blink 2times.
You can now pair into a different zone. #RAZ-Q4RF Wireless WallControl Installation
1. Install the Long Life Cr2032 batteryinthe touchpad.
(Can be used as a handheld remote)
2. Securely attach the touchpad to the mounting plate.
3. Install the touchpad mounting plate assembly into the
desired electrical box location. The #RAZ-Q4RF can be
gaged with otherswitches.
4. Attach your cover plate (not included) and you're
ready to pair your receiver to your touchpad.
r
m ----7,----
-
IJ
----7,----
• C( RoHS @
O LEDPuck
Note

2
RAZ-WR96 HOOKUP GUIDE
1. Removecover with Phillips screwdriver.
Pre-installation
2. Loosenthe4flatheadterminalscrewsusingthe
flat blade screwdriver. Connect the male and
female plugcables,orconnectionwire.Tighten4
screws. (+Redwire)(-Blackwire)
3. Attach cover with Phillips screwdriver.
Donotovertighten.
4. Attachthefemalebarrelconnectortothemale
plug cable. Push together to make theconnection.
4
Toolsrequired
(±)
Q
Wire
Strippers
FlatBlade
Screwdriver
Philips
Screwdriver

RAZ-WR96 HOOKUPGUIDE
Option 2
CutStripanduse
8MM-EZ connector
5. Cutthe connection wiretodesired lengthand routeto
LED strip location. Strip wire back 3/16"andinsert intothe
Femalebarrelconnectorterminals.(Redto + andBlackto-)
Tighten screws down with Philips screwdriver
5.RoutewirefromreceiverbarrelplugtoLEDstrip.Connect
tostrip using Option 1orOption 2.(Seethe 8MM-EZ guide
fordetailedcuttingandconnectinginstructions)
7.Verifythatallconnections polarity arecorrect
(Redto + and Blackto -}
9. Plug inthe power supply and proceedtothe
pairing instructions
8.Connect the male endofthe powersupplytothe
Female plugcable.
Watch the Video
www.veraled.com
7
8
9

one zone
PAIR ING INSTRUCTIONS
Afteryouhavewiredallthe receiversaccordingtoyour projectrequirements, dothefollowing:
1. Ifyou use multiple receivers, you have two choices:
(1)haveallthereceiversinthesamezone,likezone1,or
(2) Haveeachreceiverinadifferent zone,likezone1,2,3or
4.
2. Inorderfor each receiver toknowwhat Zone itbelongto,
youwill needto "pair"ittothezoneyouwishtouse. In
ordertodothis, youneedtopoweruptheunitwiththe
LED lights hooked toit.
3. Resetthe receiver bypressing and holdingthe "Learning"
button untilthe lights blink 2times.
4. To "pair" you needtoquickly andfirmly pressand release
the "Learning" button onthe receiver and immediately after
that,youwillneedtoquicklypressandreleasethe ON and
OFF buttonontheRAZ-Q4RFcontrolforthezoneyouwant
to use.
Watch the Video
5. Once you dothat,the lightswill blinkonce.
Nowyour Remote and Receiver are paired.
www.veraled.com
3
4
1
Option1
All receivers in
Option 2 each receiver i n different zones
2
5