QUBE LIGHTING BEAM 7R User manual

230W BEAM English

2


Thank you for using our products, is safe and effective use of this product to you, before you use this
product, please read this instruction manual carefully complete. This manual contains: the perfor-
mance of the product is and how to safely install, and use of important information, please properly
keep, in order to use as a reference. When installing and using relevant instructions must be strictly
observed.
Beam 7R 230W light Beam, the new revolution of headlamp! Lighter... The total quality is only
17KG! Faster... The X/Y axis moves faster, smoother and less noisy! The software band corrects
positioning function, makes up the hardware error, the positioning accuracy is quite high! Complete-
ly solve X/Y position! Brighter... 3 in combination with optical lens, the color temperature reaches
8500K, which is higher than 700W, 1500W beam light and higher color temperature! Lower... Light
bulb power only 200W, total power only 290W low power! Stronger... The beam feels stronger, the
parallel light is sharper! Intelligent light bulb switch control to extend bulb life! More... More powerful,
more powerful, 16CH / 20CH channel: 14 colors, 17 designs, rotating 8 prisms, atomization, strobe!
Power supply: AC100V - 240V
Frequency: 50hz - 60hz
Total power: 290W
Fuse: 5A
Ballast: Electronic Ballast
Light source: OSRAM (7R) light bulb
Light bulb power: 230W
Color temperature: 8500 k
Average life span: 2000H (light bulb and reective cup overall package
light efciency and higher service life)
Control signal: International standard DMX512
Appearance: High temperature resistant plastic
Light body color: black
Protection level: IP20
Weight: 17kg
Operation parameters:
Product description:





The lamps and lanterns use DMX512 signal control model, the control signal of lamps and lanterns
is a parallel relationship, the connection is more than one signal lamps and lanterns, it is best to use
double core shielded cables. Connection, all through the lamps and lanterns of lamps and lanterns
DMX signal on jack (context) INPUT (INPUT) and OUTPUT (OUTPUT) are connected, connect the
line of lamps and lanterns 3 core XLRXL plug terminal must correspond to each other, when the con-
nection signal lamps and lanterns, it is recommended to use DMX signal terminal. Can be avoided,
due to electrical noise damage control signal, DMX signal terminal device is a XLR plugs connection
between 2 and 3 feet a 120 ohm resistance of 1 w, and connect it on the last stage of lamps and
lanterns of the OUTPUT (OUTPUT) jack.
1. The international standard control signal: DMX512
2. The number of channels: 16Ch
3. The number of motor: a total of 10 mute motor
4. The X axis rotate for 540°, the Y axis vertical rotation of 270°, with automatic correction
5. The dimming: 0-100% linear adjustment
6. Stroboscopic: Double chip stroboscopic (0.5-9 times/SEC), completely linear dimming and
variable stroboscopic speed
7. Color wheel: With 14 kinds of color + blank (can create sharp air beam effect)
8. Pattern wheel: With a 17 xed pattern piece + blank (lets you quickly change the beam shape)
9. A prism: Rotating eight prism, can be bi-directional rotation, rotation speed is adjustable, making
a richer pattern projection effect
10. Itemization: Soft light effect, the design of soft dream effect
11. Focus: adopting the combination of three groups of optical lens effect is much better than the
beam of light, usually can reects the pattern of hid
12. The beam Angle: Parallel beam Angle 0° - 3.8°
13. Overheating intelligent protection
14. Smart bulb switch control, prolong the service life of the bulb
Function Description:
Connection of DMX512 signal:

4


The starting address code of the current light xture is equal to (the initial address code of the last
light xture) + (the number of channels of the lamp) :
1. The initial address code of the rst lamp is A001.
2. The basic channel number of the controller should be greater than or equal to the total number of
use channels.
3. When using any controller, each lamp should have its own initial address code. If the initial ad-
dress code of the rst light lamp is set A001, the number of the luminaire number is 16CH; The
starting address of the second light xture is set to A017. The starting address code of the third light
xture is set to A033; And so on and so forth, (this setting also needs to be determined by different
control tables)
This luminaire can be placed horizontally, slanting and hanging upside down, and must pay attention
to the installation method when hanging and hanging upside down.
Fixed installation of lamps and lanterns: before the positioning of lamps and lanterns, to ensure the
stability of the installation site, when the reverse hanging installation, must ensure that the lamps
and lanterns is not tumbled down on the supporting frame and handle with a safety rope through the
racks and lamps and lanterns, assist hanging; In order to ensure safety. To prevent fall and slide of
lamps and lanterns, lamps and lanterns in the installation and debugging, the ban pedestrians pass,
regularly check whether the safety rope appear wear away, whether hook screws loosen, if because
hanging installation is not stable, lead to fall all consequences arising from the lamps and lanterns
manufacturer does not assume any responsibility.
1. When replacing the bulb, remove the plastic shell of the lamphead rst.
2. Good quality light bulbs are recommended.
3. Uncharged installation, remove the bulb.
4. Hand untouchable parts of the bulb.
5. Tighten the screws after replacing the bulb.
6. The light bulb work at high temperature, and gas discharge can not continue to supply the physi-
cal characteristics of bubble, must therefore be in every time, when the power is completely cooling
ability to operate in about 10 minutes, otherwise it will lead to high voltage discharge, short circuit
burn out components on the computer console.
The initial address code calculation method of lamps and lanterns:
The initial address code calculation method of lamps and lanterns:
Light bulb installation:

5



1. Non-professional personnel, do not remove the ttings in lamps and lanterns without permission.
2. AC power supply: check whether the local power supply meets the rated voltage requirement.
3. The lamps and lanterns is according to the type of electric shock protection design, lamps and
lanterns should be used with sufcient power supply system grounding, and lamps and lanterns of
the ground wire must be connected to the ground of the power supply system. Do not use insulation
damaged power cord, at the same time, do not use the power cord overlap on the other wire.
4. When the installation location and lamps and lanterns, any point on the surface of lamps and
lanterns and any easy to burn the explosive keep minimum distance of 10 meters, 2.5 meters from
irradiation distance, please do not install the lamps and lanterns is directly in to burn the material
surface.
5. Ambient temperature used in luminaires: (-10 degrees + 40 degrees), the maximum temperature
of the lamp surface is 80 degrees, and the lamps and lanterns should be kept away from the liquid
material and wet environment.
6. Make sure the lamps are well grounded before using the lamps, and do not install and remove
any parts.
7. When installing lamps and lanterns, the xing screws must be fastened, equipped with safety
cables and checked regularly.
8. The continuous working time of the luminaires should not exceed 10 hours, and the interval time
of continuous start of the lamps shall not be less than 10. Otherwise, the bulb should be protected
from overheating and cannot be triggered normally.
9. In the process of use, the lamp should be stopped using lamps in time.
10. When the bulb reaches the rated service life, it should be replaced in time, or there will be a
dangerous explosion.
11. The rotating part of the lamp and the pasting accessories must be checked regularly and loos-
ened, and the shaking should be strengthened in time to prevent accidents.
12. Lamps and lanterns uses strong wind cooling and accumulates dirt easily. Must be cleaned once
a month especially the cooling tuyere otherwise will be in a dust jam, lead to bad heat dissipation.
Safety tips!
To ensure your safe use of lamps, read the following safety tips carefully before
using them to avoid unnecessary breakdowns and injuries.

6


One. Light bulbs
1.1. Due to improper operation, the bulb has not been completely cooled. The lamp should be
cooled for more than 10 minutes, so that the inner bulb of the bulb can be fully restored to normal
state, and the power supply can be started again.
1.2. Check whether the bulb has reached the service life and should replace the new bulb.
1.3. Check whether the bulb and the bubble line are leaking, shedding or not having good contact.
1.4. Replace the new point bubbler.
Two. The beam appears dim
2.1. Check whether the bulb has reached the service life and should replace the new bulb.
2.2. Check that the optical parts or light bulbs are clean, and the light bulbs and other optical devices
are accumulated with dust, and the light bulbs and components should be cleaned and maintained
regularly.
Three. The projected image is blurred
3.1. Check whether the electron focus channel value is suitable for the current projection distance.
Four. Computer lights work intermittently
4.1. Check whether the fan is running normally to make it dirty.
4.2. Check whether the internal temperature control switch is closed.
4.3. Check whether the bulb has reached the service life and should replace the new bulb.
Five. Although it glows, the computer lamp no longer accepts controller control
5.1. Check the initial address code and check the connection of the communication line (1 ground
2 minus 3 positive)
5.2. Add signal amplier
5.3. When the bulb was not completely cooled, there was an abnormal start operation, and the in-
stantaneous ultra-high voltage of the bubbler was leaking and the CPU of the circuit board channel
chip was burned.
Six. Computer light cannot be started
6.1. Check whether the insurance on the power input socket is fused
6.2. Lamps and lanterns are not in contact with the line due to vibration during long distance trans-
portation
6.3. Check the input power, computer board and other connector devices
Difcult method:
The following is a list of troubleshooting and processing methods.
Other maintenance tasks are handled by professional maintenance personne





7. After self-examination, some functions do not accept controller control
7.1. Check that the function has no power at work, or whether the chip is burned by other high pres-
sure shocks.
8. The X and Y axis in the other data have been restored to 0 in the other data,
and abnormal noises have occurred
8.1. At the time of abnormal qi, the high point bubble voltage leakage caused the burning of X and
Y axis photoelectric induction circuit board (light lotus root).
8.2. Restart the computer light according to normal procedures
8.3. Push all the channel values of the controller to 0, remote reset computer lamp.
Maintenance and insurance:
Shutdown operation: before each off, the bulb rst closed 10 minutes ahead of time. Let the cooling
fan inside heat when using the lamps and lanterns, fast discharge, it can prolong the lamps and lan-
terns of accessories, especially the service life of the bulb! In order to ensure the lamps and lanterns
can steadily run, should keep it clean, open lamps and lanterns for repair or before maintenance
work that make sure the power is disconnected, it is important to keep the lamps and lanterns is
clean, clean, clean, please regularly not only keep the maximum brightness output, but also can pro-
long the service life of lamps and lanterns, it is recommended to use high quality glass cleaner and
use a clean soft cloth to clean, use the vacuum cleaner at least half an year is clean inside the lamp.
After-sales service
Attention! When the lamps and lanterns are out of the factory, they are strictly inspected and the
packing is in good condition. Please follow the instructions.
The fault of the machine is not covered by the machine.
1. The company will provide technical advice to customers throughout the lifetime.
2. If the product failure, need to repair, please show me your product warranty card, and ll in related
content. At the same time also hope to customers in a timely manner the problems in the products
back to us, convenient for our rst time to improve the product.
3. Besides the luminaires, the following accessories can also be selected:
Attachment: power line: 1, signal line: 1, instruction: 1 copy
The choose and buy a
Light bulb (customer request)
Light hook safety cable (customer selection)

8


Software features:
1. LCD 650,000 color touch TFT interface, easy to operate and beautiful interface.
2. Physical buttons and touch are both completely independent and can be used in
combination
3. Complete all operations independently with the physical keys
4. Complete all operations independently with touch
5. Use the physical buttons and touch mode to complete all operations
6. Intelligent height
7. For example: check all, the decoupling error in the reset, and give hints.
8. Reset calibration (zero calibration)
9. X axis, Y axis, color wheel, pattern disk
1. Display instructions:
Main interface specication
The knob of the display is used as a selection key. Rotate the buttons left and right to
change the selected function. Press to indicate OK
How to check the lamp time
Press the menu mark (as the frist picture)
OTHER INDORM--LAMP TIME--check the time
2.How to reset the lamp
Press the reset mark(as the second picture)--ADV--USE MANG-- PASSWAORD1 :3
PASSWAORD2 :4---KEY--nd RST LAMP -- TRUN IT ON--SAVE--ESC





9



3. How to make change for the language
4. How to change the run model
Press button as the rst picture,then you can see run mode, there have three modes
to show different effects. Such as AUTO, WIRE,DMX, choose the mode you want
here,and remermber press save.
5. How to make color /gobo/ xy/calibration

Press this button







Press button as the frist picture--ADV--Zero Set--- PASS-
WORD 1---Key--Then you can change what you want to
change

 


6.How to make reset on the display
7.How to set sound mode
Press button as the frist picture--TEST RUN--SOUND
8. How to check beam info


Press button as the frist picture--OTHER INFO






Press button as the rst
picture--RESET