QubicaAMF CenterPunch User manual

OWNER’SMANUAL
CENTERPUNCH
LIGHTING
EFFECTSSERVER
P/N: 400275000 REV. F, 03/22

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22
ALL RIGHTS RESERVED
All rights to this manual, including the diagrams, figures, and technical specifications, are the property of
QubicaAMF. Reproduction or transmission of any of the material contained in this manual without the prior
written permission of QubicaAMF is strictly prohibited. All of the product information in this manual was
carefully prepared based on the latest information available and was believed to be correct at the time of
printing. While every effort has been made to ensure accuracy, this publication may inadvertently contain
typographical errors, inaccuracies, or errors of omission. QubicaAMF cannot be held responsible for any
claims resulting from these errors.
DOCUMENT UPDATES
QubicaAMF reserves the right to revise and/or update this manual at any time without obligation to notify
any person or entity of such revision. The document number, revision level, and date below indicate the
edition of this manual.
TRADEMARK NOTICES
QubicaAMF and the QubicaAMF logo are the trademarks of QubicaAMF.
CONDITIONAL INFORMATION
This manual assumes that the QubicaAMF equipment and/or software has been installed by a QubicaAMF-
authorized technician and is functional in every aspect. Should you encounter problems in operating the
equipment, follow the instructions in this manual before contacting QubicaAMF for service under warranty.
WORLDWIDE HEADQUARTERS
8100 AMF Drive
Mechanicsville, VA 23111 - USA
Phone: [phone]
Fax: [phone]
EUROPEAN HEADQUARTERS
Via della Croce Coperta, 15
40128 Bologna - Italy
Phone: [phone]
Fax: [phone]
For more contact information, go to
https://www.qubicaamf.com/contact/find-your-closest-representatives/

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22
Table of Contents
SUMMARY OF CHANGES..........................................................................................................I
GENERAL INSTALLATION NOTES..............................................................................................II
TEMPERATURE AND HUMIDITY REQUIREMENTS .....................................................................II
1COMPONENTS ..............................................................................................................1
1.1 Effect Server X ............................................................................................................................ 1
1.1.1 Installation notes.............................................................................................................. 1
1.1.2 Label description.............................................................................................................. 1
1.1.3 Connections...................................................................................................................... 1
1.2 4DMX-HUB ................................................................................................................................. 2
1.2.1 Installation notes.............................................................................................................. 2
1.2.2 Label description.............................................................................................................. 2
1.2.3 Connections...................................................................................................................... 2
1.3 5HD-CPU and 4HD-CPU .............................................................................................................. 3
1.3.1 Installation notes.............................................................................................................. 3
1.3.2 5HD-CPU Label description .............................................................................................. 3
1.3.3 4HD-CPU Label description .............................................................................................. 4
1.3.4 Connections...................................................................................................................... 4
1.4 How to install the CenterPunch Lighting Effects Server............................................................. 5
1.4.1 Prepare your CenterPunch Lighting Effects Server (Effect Server X unit ONLY).............. 5
1.4.2 Prepare your CenterPunch Lighting Effects Server (4DMX-HUB unit ONLY)................... 5
1.4.3 Fix the CenterPunch Lighting Effects Server to the wall.................................................. 5
T.90.255 –CenterPunch Lighting Effects Server suggested installation .......................................... 6
1.4.4 Connect the system.......................................................................................................... 7
1.4.4.1 Connection in the case of EDGE String equipped with SYSTEM CONTROLLER, ES
P/N: 051-200-90X-YY ............................................................................................. 7
1.4.4.2 Connection in the case of Effect Server X.............................................................. 8
1.4.4.3 Connection in the case of 4DMX-HUB with 4HD/5HD-CPU................................... 9
2SOFTWARE CONFIGURATION ......................................................................................11
2.1 CenterPunch Lighting Effects Server first startup procedure .................................................. 11
2.2 How to setup a new light effect combination.......................................................................... 12
2.2.1 How to create and setup a new light effect combination –Conqueror X ..................... 12
2.2.2 How to create and setup a new light effect combination –Conqueror Pro.................. 13
2.3 Use the light effect combinations ............................................................................................ 14
2.3.1 How to setup light effect combinations in Bowling modes - Conqueror X.................... 14
2.3.2 How to setup light effect combinations in Bowling modes - Conqueror Pro ................ 15
2.3.3 How to setup light effect combinations in Lane options............................................... 16
2.4 How to perform a light effect from the Special Functions menu ............................................ 17
2.4.1 Conqueror X ................................................................................................................... 17
2.4.2 Conqueror Pro................................................................................................................ 18
3REPLACEMENTS ..........................................................................................................19
3.1 How to replace the Effect Server X or the 4DMX-HUB units.................................................... 19
3.2 How to replace the 4DMX-HUB unit ........................................................................................ 20
4PARTS.........................................................................................................................21

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22
This page intentionally left blank

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22 I
SUMMARY OF CHANGES
REV. F (03/22, ECR 22-0074):
-Added Temperature and Humidity requirements paragraph, on page II;
Chapter 1:
-Updated Connections paragraph, on page 1.
-Added Connection in the case of EDGE String equipped with SYSTEM CONTROLLER, ES P/N: 051-
200-90X-YY paragraph, on page 7.
Chapter 2:
-Updated CenterPunch Lighting Effects Server first startup procedure paragraph, on page 11.
-Updated How to setup a new light effect combination paragraph, on page 12.
-Added How to create and setup a new light effect combination –Conqueror X paragraph, on page
12.
-Updated Use the light effect combinations paragraph, on page 14.
-Added How to setup light effect combinations in Bowling modes - Conqueror X paragraph, on page
14.
-Updated How to setup light effect combinations in Lane options paragraph, on page 16.
-Updated How to perform a light effect from the Special Functions menu paragraph, on page 17.
Chapter 3:
-Updated How to replace the Effect Server X or the 4DMX-HUB units paragraph, on page 19.
REV 5(02/19)
REV 4(12/18)
REV 3(06/17)
REV 2(03/17)

CenterPunch Lighting Effects Server Owner's Manual
II P/N: 400275000; Rev. F, 03/22
General installation notes
For devices directly connected to the power, it is necessary to check that the electrical capacity of the system
is suitable for the maximum power requirements of the equipment (as indicated on the labels of the
equipment).
Always open the circuit breaker and disconnect the power plug from the powered units before looking for,
and clearing, any problem.
To reduce the risk of fire or electrical shock, do not expose this equipment to moisture.
This appliance must be positioned such that the mains supply cord connector is accessible after installation.
Be aware of the voltage being supplied to the equipment (i.e. from 100V to 240V) and that the equipment is
set for the correct voltage (when applicable).
Failure to set the equipment for the correct voltage will result in damage to the equipment.
The electrical safety of the equipment is obtained only when the equipment is connected to an effective
GROUNDING SYSTEM (in accordance with the existing electrical codes and safety regulations).
It is necessary to have the power and grounding inspected by a licensed and certified electrician.
The manufacturer cannot be responsible for possible injury, damages or malfunctioning of the equipment
due to the absence of or improper grounding of the equipment.
Temperature and Humidity requirements
All QubicaAMF ELECTRONIC products are specifically designed and engineered to be used inside a bowling
center environment.
QubicaAMF ELECTRONIC equipment has an OPERATING temperature range of 15° to 35° C (59° to 95° F) and
an OPERATING humidity range of 10% to 80%.
Temperatures and humidity levels outside the listed ranges will negatively affect the operation and lifespan
of the QubicaAMF ELECTRONIC equipment.
QubicaAMF strongly suggests not to use or store any of the supplied electronic equipment where the
temperature and humidity level cannot stay within the specified ranges.
Restrictive temperature and humidity requirements are specified by the producer of the lanes that will not
be listed inside this manual.

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22 1
1Components
The CenterPunch Lighting Effects Server is the interface used to control the lights from a Conqueror X/Pro
front desk terminal. It could have different configurations:
-Effect Server X;
-composed by 2 units: the 4DMX-HUB unit and a 5HD-CPU unit;
-composed by 2 units: the 4DMX-HUB unit and a 4HD-CPU unit.
1.1 Effect Server X
The Effect Server X is the interface between each QAMF lighting system with the Conqueror X/Pro front desk
computer. The main functionalities of this unit is to permit the communication between the front desk PC
and the lights.
1.1.1 Installation notes
The Effect Server X communicates with the front desk via a standard network by the N1 connector, located
on the upper side of the unit.
WARNING: NEVER connect, for any reason, a standard network device (such as a network switch) to a port
different than the N1 port. Connecting a standard network device to a port different than N1 may result in
major damages for the device or for the Effect Server X unit itself.
1.1.2 Label description
The image above displays the label located on the side of the 4DMX-HUB unit.
1. Manufacturer (QubicaAMF Europe S.p.A.).
2. Part number (P/N: 275002032).
3. List of certifications (CE certification).
4. Name of the unit (Effect Server X).
5. Electrical notes (100-220 V; 3.8-1.9 A; 50/60 Hz).
6. Serial number with bar code.
1.1.3 Connections
Power Specifications for the Effect Server X are: 100 - 220 V; 3.8 - 1.9 A; 50 - 60 Hz.
On the Effect Server X the following connections are available:
Connectors on the left side of the 4DMX-HUB unit:
•D1 DMX COM LINE:
oWhen EDGE String pinspotter equipped with a “SYSTEM CONTROLLER, ES”
P/N: 051-200-90X-YY is present: connect here the “DMX 1 IN/OUT” port of the SYSTEM
CONTROLLER, ES unit installed on the first lane for the DECK LIGHTING.

CenterPunch Lighting Effects Server Owner's Manual
2 P/N: 400275000; Rev. F, 03/22
oWhen EDGE String pinspotter equipped with a “SYSTEM CONTROLLER, ES”
P/N: 051-200-90X-YY is NOT present: connect here the first DMX Dimmer 2 unit for the DECK
LIGHTING.
•D2 DMX COM LINE: Connect here the first DMX Dimmer 2 unit for the CAPPING LIGHTING.
•D3 DMX COM LINE: Currently NOT used.
•D4 DMX COM LINE: Currently NOT used.
•POWER INPUT: Connect here the power line (range: 100 - 240 V; 50/60 Hz).
Connectors on the upper side of the CenterPunch Lighting Effects Server unit:
•N1 Network: Standard network connection to the scoring network.
•U1: Currently NOT used.
1.2 4DMX-HUB
The 4DMX-HUB is the interface between the 4HD/5HD-CPU with the Conqueror X/Pro front desk computer.
The main functionalities of this unit is to permit the communication between the front desk PC and the DMX
pit lights.
1.2.1 Installation notes
The 4DMX-HUB communicates with the front desk via a standard network by the N1 connector, located on
the upper side of the unit. It is connected to the 4HD/5HD-CPU (that should be mounted on the front panel
of the 4DMX-HUB) connecting the L1 CPU COM LINE connector on the unit to the L1 connector on the upper
side of the 4HD/5HD-CPU.
WARNING: NEVER connect, for any reason, a standard network device (such as a network switch) to a port
different than the N1 port. Connecting a standard network device to a port different than N1 may result in
major damages for the device or for the 4DMX-HUB unit itself.
1.2.2 Label description
The image above displays the label located on the side of the 4DMX-HUB unit.
7. Manufacturer (QubicaAMF Europe S.p.A.);
8. Part number (P/N: 275002011);
9. List of certifications (CE certification);
10. Name of the unit (4DMX-HUB);
11. Electrical notes (100-240 V; 1.3 - 0.6 A; 50/60 Hz);
12. Serial number with bar code.
1.2.3 Connections
Power Specifications for the 4DMX-HUB are: 100 - 240 V; 1.3 - 0.6 A; 50 / 60 Hz.
On the 4DMX-HUB the following connections are available:

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22 3
Connectors on the left side of the 4DMX-HUB unit:
•L1 CPU COM LINE: Network connection with POE for the 4HD/5HD-CPU.
•ANET1: Currently not used.
•ANET2: Currently not used.
•ANET3: Currently not used.
•P1 AUX: Currently not used.
•D1 DMX COM LINE: Connect here the first DMX Dimmer 2 unit.
•POWER INPUT: Connect here the power line (range: 100 - 240 V –50 / 60 Hz).
Connectors on the upper side of the CenterPunch Lighting Effects Server unit:
•N1 Network: Standard network connection to the scoring network.
1.3 5HD-CPU and 4HD-CPU
IMPORTANT NOTE: the 5HD-CPU unit, P/N: 288250023, is supported by Conqueror Pro version 12 or higher.
The 4HD-CPU and the 5HD-CPU are the core unit for the CenterPunch Lighting Effects Server. Their
functionality is to control the DMX pit lights. They are connected to the 4DMX-HUB unit with a single network
cable and must be installed on the front panel of the 4DMX-HUB unit.
1.3.1 Installation notes
The 4HD/5HD-CPU unit communicates with the 4DMX-HUB via a standard network with POE. The connection
between the 4HD/5HD-CPU and the 4DMX-HUB is between the L1 port of the 4HD/5HD-CPU unit and the L1
port of the 4DMX-HUB, as explained in this manual.
1.3.2 5HD-CPU Label description
The image above displays the label located on the side of the 5HD-CPU unit.
1. Manufacturer (QubicaAMF Europe S.p.A.);
2. Name of the unit (5HD-CPU);
3. Part number with bar code (P/N: 288250023);
4. List of certifications (CE certification);
5. Serial number with bar code;
6. Electrical specifications (12 VDC Max 30W Ext. Pow. Plug).

CenterPunch Lighting Effects Server Owner's Manual
4 P/N: 400275000; Rev. F, 03/22
1.3.3 4HD-CPU Label description
The image above displays the label located on the side of the 4HD-CPU unit.
1. Manufacturer (QubicaAMF Europe S.p.A.);
2. Name of the unit (4HD-CPU);
3. Part number with bar code (P/N: 288250020);
4. List of certifications (CE certification);
5. Serial number with bar code;
6. Electrical specifications (12 VDC Max 33W Ext. Pow. Plug).
1.3.4 Connections
On the 4HD/5HD-CPU the following connections are available (NOTE: we will describe here only the
connections used for the CenterPunch Lighting Effects Server):
Connectors on the upper side of the 4HD/5HD-CPU unit:
•L1: Network connection to the 4DMX-HUB unit.

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22 5
1.4 How to install the CenterPunch Lighting Effects Server
IMPORTANT: Prior to the installation of your new lighting system, please contact the QubicaAMF Tech
Support service to schedule an appointment to update your software before integrating the lighting system
with Conqueror Pro. You will need Tech Support assistance before you will be able to use your new lights.
1.4.1 Prepare your CenterPunch Lighting Effects Server (Effect Server X unit ONLY)
Take note of the serial number of the Effect Server X, written on its label. Loose the black nut and remove
the wall support from the rear of the Effect Server X.
1.4.2 Prepare your CenterPunch Lighting Effects Server (4DMX-HUB unit ONLY)
Fix the 4HD/5HD-CPU to the front side of the 4DMX-HUB, using the two screws present on the 4DMX-HUB
and take note of the serial number of the 4HD/5HD-CPU, written on its label. Loose the black nut and remove
the wall support from the rear of the 4DMX-HUB.
1.4.3 Fix the CenterPunch Lighting Effects Server to the wall
Choose the position where you want to install the CenterPunch Lighting Effects Server. We strongly suggest
to install the unit on the rear of the curtain wall, near the first DMX dimmer unit. Then fix the wall support
to that position using four screws. Be sure to fix it with the side with the N1 connector facing upwards. Finally
fix the CenterPunch Lighting Effects Server to the wall support and tight the black nut.

CenterPunch Lighting Effects Server Owner's Manual
6 P/N: 400275000; Rev. F, 03/22
T.90.255 –CenterPunch Lighting Effects Server suggested installation
CENTERPUNCH
LIGHTING
EFFECTS SERVER
DMX DIMMER 2
UNITS
HOME RUN
CABLE
MAIN
SCORING NET
SWITCH

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22 7
1.4.4 Connect the system
FOR BOWLAND / BOWLAND-X CENTERS ONLY: Install the supplied network switch on the rear of the curtain
wall, in the middle of the lanes (for example between lanes 4 and 5 in an eight lanes center). We will call it
MAIN Scoring Network switch. Connect the second network card of the Conqueror X/Pro Server computer to
the MAIN Scoring Network switch, using the 250 ft. (75 m) network cable.
1.4.4.1 Connection in the case of EDGE String equipped with SYSTEM CONTROLLER, ES
P/N: 051-200-90X-YY
Connect the “N1 NETWORK” plug of the Effect Server X to the MAIN Scoring Network switch.
Connect the “D1 DMX COM LINE” to the “DMX 1 IN/OUT” of the first SYSTEM CONTROLLER, ES unit for the
DECK LIGHTING.
Connect the “D2 DMX COM LINE” to the first DMX Dimmer unit of the CAPPING LIGHTING.
Connect the DMX 120 Ohm terminator to the “D2 DMX IN/OUT” connector of the last SYSTEM CONTROLLER,
ES unit and/or the last DMX Dimmer 2 unit.
Power on the CenterPunch Lighting Effects Server: connect the power cable to the Effect Server X and plug
it into an electrical outlet.

CenterPunch Lighting Effects Server Owner's Manual
8 P/N: 400275000; Rev. F, 03/22
1.4.4.2 Connection in the case of Effect Server X
Connect the “N1 NETWORK” plug of the Effect Server X to the MAIN Scoring Network switch.
Connect the “D1 DMX COM LINE” to the first DMX Dimmer unit of the DECK LIGHTING.
Connect the “D2 DMX COM LINE” to the first DMX Dimmer unit of the CAPPING LIGHTING.
Connect the DMX 120 Ohm terminator to the “D2 DMX IN/OUT” connector of the LAST DMX Dimmer 2 unit.
Power on the CenterPunch Lighting Effects Server: connect the power cable to the Effect Server X and plug
it to an electrical outlet.

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22 9
1.4.4.3 Connection in the case of 4DMX-HUB with 4HD/5HD-CPU
Use the shortest supplied network cable to connect the “L1 CPU COM LINE” plug of the 4DMX-HUB to the
“L1” plug of the 4HD/5HD-CPU.
Connect the “N1 NETWORK” plug of the 4DMX-HUB to the MAIN Scoring Network switch.
Connect the “D1 DMX COM LINE” to the first DMX Dimmer unit.
Connect the DMX 120 Ohm terminator to the “D2 DMX IN/OUT” connector of the LAST DMX Dimmer 2 unit.
Power on the CenterPunch Lighting Effects Server: connect the power cable to the 4DMX-HUB and plug it to
an electrical outlet.

CenterPunch Lighting Effects Server Owner's Manual
10 P/N: 400275000; Rev. F, 03/22
This page intentionally left blank

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22 11
2Software configuration
IMPORTANT: Prior to the installation of your new lighting system, please contact the QubicaAMF Tech
Support service to schedule an appointment to update your software before integrating the light system with
Conqueror Pro. You will need Tech Support assistance before you will be able to use your new lights.
2.1 CenterPunch Lighting Effects Server first startup procedure
1
On a front desk computer, navigate through the Conqueror X main menu and select:
SETUP / Modules & Options Setup / Upload to Lighting.
OR
On a Conqueror Pro terminal select: SETUP / TECHNICAL SETUP / CENTERPUNCH DECK LIGHTING
2
Once in the “Lane Lighting Server Setup” screen, check the “Enabled” option, enter the Serial number of the Effect Server X
(or 4HD/5HD-CPU) that has been previously taken (in this example the serial number of the 4HD/5HD-CPU is 05355). Then
press the “Save” button
3
When the CenterPunch Lighting Effects Server has completely booted up, the circle near the serial number
changes color from red to green.
4
Reinitialize the Effects Server.
5
Click on “Yes” in the confirmation window.
6
When the message “Upload terminated: UPLOAD COMPLETED” appears in the “Upload status” text box and the circle near
the serial number turns green, the reinitialization process has been completed and the CenterPunch Lighting Effects Server is
ready.

CenterPunch Lighting Effects Server Owner's Manual
12 P/N: 400275000; Rev. F, 03/22
2.2 How to setup a new light effect combination
2.2.1 How to create and setup a new light effect combination –Conqueror X
Follow this procedure to setup a new light effect combination. In this example we will setup a light effect for a strike event:
1
On a front desk computer, navigate through the Conqueror X main menu and select:
SETUP / Modules & Options Setup / Lights –Lane effects.
2
The “Lights –Lane effects” screen will open, there are two (2) preset Lane effect combinations, selectable by clicking on the
drop down menu: COMPETITION and OPEN PLAY. Otherwise click on:
Create a new lane effects combination.
Copy the selected lane effects combination.
Rename the selected lane effects combination.
Delete the selected lane effects combination.
3
Double click on the event that you want to modify to access the “Lane effect” modification screen.
4
Click on OK when finished to modify the selected lane effect.
5
Click on Test effect to test the current lane effect on to the selected lanes.
6
Click on Save once finished.

CenterPunch Lighting Effects Server Owner's Manual
P/N: 400275000; Rev. F, 03/22 13
2.2.2 How to create and setup a new light effect combination –Conqueror Pro
1
On a Conqueror Pro terminal select: SETUP / BOWLING SETUP / CENTERPUNCH DECK LIGHTING
2
The “CenterPunch Deck Lighting” screen will open, the preset light effect combination is named “DEFAULT”.
3
Click on the “ADD” button to create a new light effect combination.
4
Enter the new light effect combination name and click on the “OK” button.
5
Click on the Events tab and select the “Strike” event.
6
Click on the “Edit effect” button (or double click on the event description).
7
The edit effect screen will open:
a) Select in the Effect list, the light effect that you want to
be performed on the lane during the selected
state/event.
b) Select the color combination to be performed by the pit
lights for the selected effect:
•From color, To color: most pit light effects are
designed to change between two colors: the one
specified in “From color” and the one specified as
“To color”.
c) For some pit light effects the option “Velocity” will be
enabled: select between the options
•Slow: to set the effect speed to slow;
•Medium: to set the effect speed to medium;
•Fast: to set the effect speed to fast.
d) For some pit light effects the option “Direction” will be
enabled: select between the options
•Left to right: to see the light effect changing from
left to right.
•Right to left: to see the light effect changing from
right to left
e) Duration (Sec): This value set the time, expressed in
seconds, for the duration for the current light effect.
f) Click on the “OK” button when finished.
8
Click on the “Test effect” button to test on the lane the currently selected Pit light effect.
NOTE: when a “State” effect is tested, it will be displayed on the lanes for almost 20 seconds. When a “Event” effect is tested,
it will be displayed for a period of time equal to the “Duration” value.
9
Repeat steps from 6 to 8 for each state or event that you want to modify.
10
Once finished click on the “Save” button.
11
Repeat from step 3 if you want to create a new Light effect combination.

CenterPunch Lighting Effects Server Owner's Manual
14 P/N: 400275000; Rev. F, 03/22
2.3 Use the light effect combinations
Once the different light effect combinations have been setup, there is the need to set them up in Conqueror X / Pro in order to utilize
them in different situations.
There are two main conditions where it is possible to change the light effect combination: Bowling modes and Lane options.
2.3.1 How to setup light effect combinations in Bowling modes - Conqueror X
In this example we have a bowling center with 6 lanes, where we set the Lights combination “OPEN PLAY” from lane 1 to lane 2 and
the Lights combination “COMPETITION” from lane 3 to lane 6.
1
On a front desk computer, navigate through the Conqueror X main menu and select:
SETUP / General / Bowling Modes.
2
In the “Lane lighting” area of the Bowling modes screen
click on the “+” button.
3
A row will appear. In this row there are the number of the
selected lanes (1-6 means from lane 1 to lane 6) and the
name of the assigned Lane Effects and Global Mood lights
combinations.
4
Double-click on the lane numbers to open the “Select lanes” screen, to change the lane selection where the assigned Lights
combination will be displayed.
5
Click on the Lane Effects and Global Moods drop-down menus to select the desired light combination to be displayed on the
selected range of lanes.
6
In the “Lane lighting” area of the Bowling modes screen click on the “+” button.
7
A new row will appear with the number of the remaining
lanes (3-6 means from lane 3 to lane 6) and the name of
the assigned Lane Effects and Global Mood lights
combinations.
9
Click on Save once finished.