Qudo TYPHOON GUARD TYGUARDBK User manual

TYPHOON GUARD GAMING CHAIR
1/10
TYGUARDBK
ASSEMBLY INSTRUCTIONS
Weight capacity: 1 0kgs
This design and instruction booklet is subject to copyright.
www.officeworks.com.au
For spare parts or hardware call [phone] or email [email protected]
1CTN

2/10
[phone]
15
Officeworks Ltd. | 236-262 East Boundary Road | Bentleigh East VIC 3165 | AUSTRALIA
• Please check you have all hardware before assembly.
• If you are missing any hardware, please contact Kyvas on [phone] or email
[email protected]
• Please ensure you have the name of the item, required hardware part and quantity.
• Please retain your receipt as proof of purchase to validate your warranty.
.
NOTE
• Do not tighten screws before all screws are in the right place.
• Do not use this product unless all bolts, screws and knobs are firmly secured.
• Check that all bolts, screws and knobs are securely tightened at least every 4 months.
CAUTION
• If parts are missing, broken, damaged or worn stop using the product until all repairs
are made using manufacturer authorised parts.
• Failure to follow these warnings could result in serious injury
WARNING
• CHILDREN MUST BE SUPERVISED.
DANGER
Assembly Video
• To view an assembly video, go to https://www.officeworks.com.au
• Search the product by item code or name:
• Click on the icon to watch the video.

I(1/4" x 1-1/8") K(5/16" x 7/8")
(1/4" x 5/8")
L
M
(1/4" x 1-1/2")
x 1x 6
x 3 x 6x 2
N
O
3/10
x1
x1 x1x5
x1 x1
A B
E F G H
C-L/C-R D
x2
x1
J(1/4" x 7/8")
x 2
(already attached)

E
F
F
G
4/10
Note: Turn over the Star Base (F) and insert Gas Lift (E) into the centre hole of Star Base (F).
Note: Push the castors (G) firmly into hole at the end of each leg.

M
6 Pcs
used to complete
this step.
L
6 Pcs
1/4" x 1-1/2" Bolt
used to complete
this step.
J
2 Pcs
1/4" x 7/8" Bolt
used to complete
this step.
I
2 Pcs
1/4" x 1-1/8" Bolt
used to complete
this step.
5/10
L
N
N
M
B
C-R
C-L
J
I
D

N
E
K
3 Pcs
5/16" x 7/8" Bolt
used to complete
this step.
Note: Place assembled seat on the Gas Lift (E). Push down firmly until connection is secure.
6/10
6
K
A

O
Your Typhoon Guard Gaming Chair is now complete and ready for use.
IMPORTANT NOTE: Periodically check and re-tighten screws
7/10
7
O
2 Pcs
1/4" x 5/8" Bolt
used to complete
this step.
Note: Remove the pre-installed screws “O”of the backrest with Allen Key then install the headrest

8/10
Thank you for your purchase. Please retain your receipt to validate warranty.
If you would like to know more about our furniture products, please visit www.officeworks.com.au
• Vacuum regularly
• Wipe PU upholstery and non-upholstered parts with a clean damp cloth and mild soap.
Wipe PU upholstery dry immediately with an absorbent dry cloth.
• Spot clean mesh with upholstery shampoo or dry powdered cleaner only. Test on a
concealed area before proceeding. Apply proprietary cleaning products strictly according
to instructions.
• Do not saturate upholstery with water or other cleaning products.
• Treat spills immediately with an absorbent cloth by blotting the spill.
• Do not use detergents, solvents or abrasive cleaners.
• Keep away and protect from direct sunlight and heat.
• Avoid contact with skin, in particular during high temperatures and humidity.
• Clean, check and tighten parts regularly.
Care Instructions

9/10
TYPHOON GUARD GAMING CHAIR
Functionality
- Sitting in the chair pull lever up.
Move your body to a comfortable
position. Lock the position by
- Adjust the headrest height up and
down by holding back and lifting the
headrest up to raise and push down
to lower.
pushing the lever down.
- To adjust chair height, pull
lever upward while lifting body
weight slightly off the seat.
- Release lever at desired height.
- To lower chair height sit fully into
the chair and pull lever upward.
- Release lever at desired height.
Your feet should be resting flat on
the floor.
Pull lever up whilst moving the
arm up or down. Release lever
at desired height.
- Hold the headrest and rotatd forward
or back to desired angle.
- Slide the lumber support up or down
to the desired location.
HEADREST
HEIGHT
HEADREST
ANGLE
LUMBER
SUPPORT
HEIGHT
Gas-Li� Tilt
Chair Tilt
Headrest Height
Headrest Angle
Lumber support Height
Arm height

10/10
Thank you for your purchase. Please retain your receipt to validate warranty.
If you would like to know more about our furniture products, please visit www.officeworks.com.au
Warranty years
Product Warranty – valid for Australian customers only
Officeworks Ltd warrants that this product will be free from defects and work as
intended for 8 years from the date of purchase by the original customer.
If the product has any defects or does not work as intended during the Warranty Period,
Officeworks will, at its election and at its expense, repair or replace the product.
This warranty does not apply:
to cosmetic damage;
to damage caused by consumables used in connection with the product (such as
cleaning products);
where the product has not been used in accordance with all provided instructions;
to damage arising from fair wear and tear;
where the product has not been subject to reasonable use;
where the product has been intentionally or negligently damaged; and/or
if the customer has attempted to repair the product.
To make a claim under this warranty, please return your product with your receipt or
proof of purchase to your nearest Officeworks store or contact 1300 633 423.
This warranty is provided in addition to any rights you may be entitled to under the
Competitions & Consumer Act 2010.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.