Quectel BC66-NA-TE-B User manual

BC66-NA-TE-B
User Guide
NB-IoT Module Series
Rev. BC66-NA-TE-B_User_Guide_V1.0
Date: 2019-11-05
Status: Released
www.quectel.com

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 1 / 27
Our aim is to provide customers with timely and comprehensive service. For any
assistance, please contact our company headquarters:
Quectel Wireless Solutions Co., Ltd.
Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai,
China 200233
Tel: [phone]
Email: [e-mail]
Or our local office. For more information, please visit:
http://www.quectel.com/support/sales.htm
For technical support, or to report documentation errors, please visit:
http://www.quectel.com/support/technical.htm
Or email to: [e-mail]
GENERAL NOTES
QUECTEL OFFERS THE INFORMATION AS A SERVICE TO ITS CUSTOMERS. THE INFORMATION
PROVIDED IS BASED UPON CUSTOMERS’ REQUIREMENTS. QUECTEL MAKES EVERY EFFORT
TO ENSURE THE QUALITY OF THE INFORMATION IT MAKES AVAILABLE. QUECTEL DOES NOT
MAKE ANY WARRANTY AS TO THE INFORMATION CONTAINED HEREIN, AND DOES NOT ACCEPT
ANY LIABILITY FOR ANY INJURY, LOSS OR DAMAGE OF ANY KIND INCURRED BY USE OF OR
RELIANCE UPON THE INFORMATION. ALL INFORMATION SUPPLIED HEREIN IS SUBJECT TO
CHANGE WITHOUT PRIOR NOTICE.
COPYRIGHT
THE INFORMATION CONTAINED HERE IS PROPRIETARY TECHNICAL INFORMATION OF
QUECTEL WIRELESS SOLUTIONS CO., LTD. TRANSMITTING, REPRODUCTION, DISSEMINATION
AND EDITING OF THIS DOCUMENT AS WELL AS UTILIZATION OF THE CONTENT ARE
FORBIDDEN WITHOUT PERMISSION. OFFENDERS WILL BE HELD LIABLE FOR PAYMENT OF
DAMAGES. ALL RIGHTS ARE RESERVED IN THE EVENT OF A PATENT GRANT OR
REGISTRATION OF A UTILITY MODEL OR DESIGN.
Copyright © Quectel Wireless Solutions Co., Ltd. 2019. All rights reserved.

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 2 / 27
About the Document
History
Revision
Date
Author
Description
1.0
2019-11-05
Speed SUN
Initial

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 3 / 27
Contents
About the Document...................................................................................................................................2
Contents.......................................................................................................................................................3
Table Index...................................................................................................................................................4
Figure Index.................................................................................................................................................5
1Introduction..........................................................................................................................................6
1.1. Safety Information.......................................................................................................................6
2Product Concept..................................................................................................................................8
2.1. Key Features...............................................................................................................................8
2.2. Functional Diagram...................................................................................................................10
2.3. Interface Distribution Diagram..................................................................................................10
2.4. Arduino Interface Definition.......................................................................................................12
3Operation Procedures.......................................................................................................................14
3.1. Operation Procedure with Single Board...................................................................................14
3.1.1. Interface Diagram of Using BC66-NA-TE-B Alone........................................................15
3.1.2. Operation Procedures of Using BC66-NA-TE-B Alone .................................................16
3.2. Operation Procedure with Multi Boards....................................................................................16
3.2.1. Interface Diagram of Using Multi Boards.......................................................................17
3.2.2. Operation Procedures of Using Multi Boards................................................................19
3.2.3. Description of Pin Connection........................................................................................19
4Electrical and Reliability Characteristics........................................................................................21
4.1. Absolute Maximum Ratings......................................................................................................21
4.2. Operation and Storage Temperatures.......................................................................................21
5Mechanical Dimensions....................................................................................................................23
5.1. Mechanical Dimensions of BC66-NA-TE-B..............................................................................23
5.2. Top/Bottom View of BC66-NA-TE-B.........................................................................................24
6BC66-NA-TE-B Kit and Accessories................................................................................................25
6.1. BC66-NA-TE-B Kit ....................................................................................................................25
6.2. BC66-NA-TE-B Kit Accessories................................................................................................26
7Appendix A References.....................................................................................................................27

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 4 / 27
Table Index
TABLE 1: KEY FEATURES OF BC66-NA-TE-B.................................................................................................. 8
TABLE 2: INTERFACES OF BC66-NA-TE-B.................................................................................................... 12
TABLE 3: PIN CONNECTION BETWEEN BC66-NA-TE-B AND STM32-L476RG MCU ................................. 19
TABLE 4: ABSOLUTE MAXIMUM RATINGS .................................................................................................... 21
TABLE 5: OPERATION AND STORAGE TEMPERATURES OF BC66-NA MODULE ..................................... 21
TABLE 6: ACCESSORIES LIST........................................................................................................................ 26
TABLE 7: RELATED DOCUMENT .................................................................................................................... 27
TABLE 8: TERMS AND ABBREVIATIONS........................................................................................................ 27

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 5 / 27
Figure Index
FIGURE 1: FUNCTIONAL DIAGRAM OF BC66-NA-TE-B ............................................................................... 10
FIGURE 2: INTERFACE DISTRIBUTION DIAGRAM OF BC66-NA-TE-B.........................................................11
FIGURE 3: ARDUINO INTERFACE DEFINITION............................................................................................. 13
FIGURE 4: INTERFACE DIAGRAM OF USING BC66-NA-TE-B ALONE......................................................... 15
FIGURE 5: UART PORTS DISPLAYED ON PC................................................................................................ 16
FIGURE 6: INTERFACE DIAGRAM OF USING MULTI BOARDS.................................................................... 17
FIGURE 7: STM32 NUCLEO-64 BOARD INTERFACE DIAGRAM (TOP VIEW)............................................. 18
FIGURE 8: STM32 NUCLEO-64 BOARD MODIFICATION DIAGRAM (BOTTOM VIEW)............................... 18
FIGURE 9: ST-LINK INTERFACE DISPLAYED ON PC.................................................................................... 19
FIGURE 10: PIN CONNECTION BETWEEN BC66-NA-TE-B AND STM32-L476RG MCU............................. 20
FIGURE 11: DIMENSIONS OF BC66-NA-TE-B (TOP VIEW)........................................................................... 23
FIGURE 12: TOP VIEW OF THE BC66-NA-TE-B............................................................................................. 24
FIGURE 13: BOTTOM VIEW OF THE BC66-NA-TE-B..................................................................................... 24
FIGURE 14: BC66-NA-TE-B KIT ASSEMBLY................................................................................................... 25
FIGURE 15: BC66-NA-TE-B AND THE ACCESSORIES.................................................................................. 26

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 6 / 27
1Introduction
In order to facilitate application development with Quectel BC66-NA module, Quectel supplies
corresponding development board (BC66-NA-TE-B) to test the module. This document helps customers
to quickly understand BC66-NA-TE-B interface specifications, electrical and mechanical details and know
how to use it.
1.1. Safety Information
The following safety precautions must be observed during all phases of operation, such as usage, service
or repair of any cellular terminal or mobile incorporating BC66-NA module. Manufacturers of the cellular
terminal should notify users and operating personnel of the following safety information by incorporating
these guidelines into all manuals supplied with the product. If not so, Quectel assumes no liability for any
user’s failure to observe these precautions.
Full attention must be paid to driving at all times in order to reduce the risk of an
accident. Using a mobile while driving (even with a handsfree kit) causes
distraction and can lead to an accident. Please comply with laws and regulations
restricting the use of wireless devices while driving.
Switch off the cellular terminal or mobile before boarding an aircraft. The operation
of wireless appliances in an aircraft is forbidden to prevent interference with
communication systems. If there is an Airplane Mode, it should be enabled prior to
boarding an aircraft. Please consult the airline staff for more restrictions on the use
of wireless devices on an aircraft.
Wireless devices may cause interference on sensitive medical equipment, so
please be aware of the restrictions on the use of wireless devices when in
hospitals, clinics or other healthcare facilities.
Cellular terminals or mobiles operating over radio signals and cellular network
cannot be guaranteed to connect in all possible conditions (for example, with
unpaid bills or with an invalid (U)SIM card). When emergent help is needed in such
conditions, please remember using emergency call. In order to make or receive a
call, the cellular terminal or mobile must be switched on in a service area with
adequate cellular signal strength.

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 7 / 27
The cellular terminal or mobile contains a transmitter and receiver. When it is ON, it
receives and transmits radio frequency signals. RF interference can occur if it is
used close to TV set, radio, computer or other electric equipment.
In locations with potentially explosive atmospheres, obey all posted signs to turn
off wireless devices such as mobile phone or other cellular terminals. Areas with
potentially explosive atmospheres include fuelling areas, below decks on boats,
fuel or chemical transfer or storage facilities, areas where the air contains
chemicals or particles such as grain, dust or metal powders, etc.

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 8 / 27
2Product Concept
BC66-NA-TE-B is a NB-IoT development board which supports Arduino interface. Designed in 70.0mm ×
74.0mm form factor, BC66-NA-TE-B can be used either alone or in conjunction with STM32 Nucleo-64
development board, to develop and debug applications which communicate with infrastructures of mobile
network operators through NB-IoT radio protocols in 3GPP Rel. 14.
2.1. Key Features
The following table describes the detailed features of BC66-NA-TE-B.
Table 1: Key Features of BC66-NA-TE-B
Feature
Details
Power Supply
USB interface:
Supply voltage range: 4.75V~5.25V
Typical supply voltage: 5.0V
Arduino interface:
Supply voltage range: 4.75V~5.25V
Typical supply voltage: 5.0V
External power supply interface:
Supply voltage range: 4.75V~5.25V
Typical supply voltage: 5.0V
Transmitting Power
23dBm±2dB
Temperature Range
Operation temperature range: -35°C ~ +75°C 1)
Extended temperature range: -40°C ~ +85°C 2)
Storage temperature range: -40°C ~ +90°C
USIM Interface
Support 1.8V external USIM card
UART Switch
Used to switch the communication object of BC66-NA main UART port
USB Interface
Support three UART ports:
Main UART (Interface0):
Used forAT command communication and data transmission.
By default, the module is in auto-baud mode, and it supports

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 9 / 27
1. 1) Within operation temperature range, the module is 3GPP compliant.
2. 2) Within extended temperature range, the module remains the ability to establish and maintain
functions such as SMS*, data transmission, etc., without any unrecoverable malfunction. Radio
spectrum and radio network will not be influenced, while one or more specifications, such as Pout,
may exceed the specified tolerances of 3GPP. When the temperature returns to the normal operation
temperature levels, the module will meet 3GPP specifications again.
3. “*” means under development.
automatic baud rates not exceeding 115200bps. When powering on
the module, the MCU has to send AT command consecutively to
synchronize baud rate with the module. When OK is returned, it
indicates the baud rate has been synchronized successfully. When
the module is woken up from light or deep mode, the baud rate
synchronized during start-up will be used directly.
Also can be used for firmware upgrade, and in such case, the baud
rate is 921600bps by default.
Auxiliary UART (Interface1):
Used for firmware debugging
Default baud rate: 115200bps
Debug UART (Interface2):
Used for firmware debugging
Default baud rate: 115200bps
Reserved UART (Interface3)
Arduino Interface
Used for connection with STM32 Nucleo-64 development board
RESET Button
Used to reset BC66-NAmodule
PWRKEY Button
Used to turn on BC66-NA module
Physical Characteristics
Size: (70.0±0.15)mm ×(74.0±0.15)mm
Firmware Upgrade
Firmware upgrade via main UART port or DFOTA
Antenna Interface
50Ω characteristic impedance
NOTES

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 10 / 27
2.2. Functional Diagram
The following figure shows a block diagram of BC66-NA-TE-B.
BC66-NA
U101
Micro USB
J301
USB-UART
Bridge
U301
Switch
J302
J308
DC-DC
U201
(U204-NM)
USIM
J401
RF
J304
J306
Arduino
LDO U203
U302/U303
Voltage-level
Translator
Micro USB Debug
J111
LDO U202
Figure 1: Functional Diagram of BC66-NA-TE-B
2.3. Interface Distribution Diagram
The following figure shows the interface distribution diagram of BC66-NA-TE-B.

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 11 / 27
J309
J305
S103
J201
J301
J302
J308
J106
J105
S102
J303
J307
S101
J104
J306D203
J202
J304
Figure 2: Interface Distribution Diagram of BC66-NA-TE-B

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 12 / 27
Table 2: Interfaces of BC66-NA-TE-B
2.4. Arduino Interface Definition
The following figure shows the Arduino interface definition of BC66-NA-TE-B.
Interface
Designator
Description
Power Supply Interfaces
J301
USB power supply interface
J202
External power supply interface
J306
Arduino power supply interface
USB-UART Interface
J301
Support 3 UART ports: Interface0/1/2
USIM Interface
J303
Micro-SIM card connector
USB Interface
J104
Used to output BC66-NA USB log
Arduino Interfaces
J305, J306,
J307, J308
Standard Arduino interfaces
RFAntenna Interface
J304
RF SMA connector
UART Switch
J302
Used to select the communication object of BC66-NA’s
main UART: “MAIN UART TO USB” or “MAIN UART TO
MCU”
PWRKEY Button
S101
Used to turn on BC66-NA module
RESET Button
S102
Used to reset BC66-NAmodule
Sleep Wakeup Button
S103
Used to wake up BC66-NA from Deep Sleep mode
Power Indicator
D203
Used to indicate the power on/off status
JTAG Interface
J309
Used to debug firmware

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 13 / 27
RI GND GND 3.3V 3.3V 5V
PSM_EINT_N PWRKEY_N RESET_N GND
UART_MCU_RX UART_MCU_TX
Figure 3: Arduino Interface Definition
hy

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 14 / 27
3Operation Procedures
This chapter mainly illustrates the operation procedures of BC66-NA-TE-B. BC66-NA-TE-B can be used
alone to upgrade firmware and debug applications based on BC66-NA module. Also, it can be used in
conjunction with an STM32 Nucleo-64 development board via Arduino interface to develop NB-IoT
applications based on STM32. The following describes the operation procedures of BC66-NA-TE-B in
different operation modes.
3.1. Operation Procedure with Single Board
This chapter elaborates the operation procedure of using the BC66-NA-TE-B alone.

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 15 / 27
3.1.1. Interface Diagram of Using BC66-NA-TE-B Alone
J301
J302 J303
J104
J304
Figure 4: Interface Diagram of Using BC66-NA-TE-B Alone

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 16 / 27
3.1.2. Operation Procedures of Using BC66-NA-TE-B Alone
1. Install USB-UART driver which can be downloaded from the following URL:
https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers.
2. Insert a Micro-SIM card into J303, and please note that a NB-IoT USIM card should be selected.
3. Connect the rod antenna with SMAconnector on J304 (RF antenna connector).
4. Switch J302 (UART Switch) to “MAIN UART TO USB” state.
5. Connect the J301 (USB power supply interface) with PC via Micro USB cable. After turning on
BC66-NA-TE-B, UART port information will be shown on “Device Manager” of PC. Interface0 is the
main UART port and can be used for AT command communication, data transmission and firmware
upgrading. Interface1/2 are auxiliary UART and debug UART respectively, both of which can be
used to output log for firmware debugging. For details of UART configuration, please refer to
Quectel_BC66-NA_Hardware_Design.
Figure 5: UART Ports Displayed on PC
In the procedure, S101 can be used to turn on BC66-NA module, S102 can be used to reset the module,
and S103 can be used to wake up the module from Deep Sleep.
3.2. Operation Procedure with Multi Boards
This chapter elaborates the operation procedure of using the BC66-NA-TE-B in conjunction with an
STM32 Nucleo-64 development board.
NOTE

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 17 / 27
3.2.1. Interface Diagram of Using Multi Boards
J309
J305
S103
J201
J301
J302
J308
J106
J105
S102
J303
J307
S101
J104
J306D203
J202
J304
Figure 6: Interface Diagram of Using Multi Boards

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 18 / 27
Figure 7: STM32 Nucleo-64 Board Interface Diagram (Top View)
Figure 8: STM32 Nucleo-64 Board Modification Diagram (Bottom View)
SB62
SB13 SB14
SB63
CN6
CN
5
CN8
CN
9
CN1
CN
22J
203
JP6
JP5

NB-IoT Module Series
BC66-NA-TE-B User Guide
BC66-NA-TE-B_User_Guide 19 / 27
3.2.2. Operation Procedures of Using Multi Boards
1. Install driver for STM32 Nucleo-64 board, which can be downloaded from the following URL:
http://www.st.com/content/st_com/en/products/evaluation-tools/product-evaluation-tools/mcu-eval-to
ols/stm32-mcu-eval-tools/stm32-mcu-nucleo/nucleo-l476rg.html.
2. Install USB-UART driver which can be downloaded from the following URL:
https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers.
3. Remove the two 0Ω resistors (SB13 and SB14) with a soldering iron, and then solder them onto
SB62 and SB63 respectively.
4. Short-circuit pin 1 & 2 of CN2, pin 3 & 4 of CN2, pin 1 & 2 of JP5 and pin 1 & 2 of JP6.
5. Insert a Micro-SIM card into J303, and please note that a NB-IoT USIM card should be selected.
6. Connect the rod antenna with SMAconnector on J304 (RF antenna connector).
7. Switch J302 (UART Switch) to “MAIN UART TO MCU” state.
8. Connect BC66-NA-TE-B with STM32 Nucleo-64 board via Arduino interface, and please connect
J305, J306, J307 and J308 of BC66-NA-TE-B to CN5, CN6, CN8 and CN9, respectively.
9. Connect CN1 of STM32 Nucleo-64 board with PC via Mini USB cable. After powering on BC66-NA
module, device information will be shown on the “Device Manager” of PC.
Figure 9: ST-LINK Interface Displayed on PC
3.2.3. Description of Pin Connection
The table below shows the pin connection between BC66-NA-TE-B and STM32-L476RG MCU, one kind
of STM32 Nucleo-64 board.
Table 3: Pin Connection between BC66-NA-TE-B and STM32-L476RG MCU
No.
MCU (Morpho)
Arduino
BC66-NA-TE-B
Remark
1
PA2
D1
CN9-2
UART_MCU_TX
Main UART port RX
2
PA3
D0
CN9-1
UART_MCU_RX
Main UART port TX