Questtel L-1SDI-SFE-TX/RX User manual
L-1SDI-SFE-TX/RX
User Manual
HD/SD-SDI Over Fiber Transmitter
and Receiver Extender Kit
1
Table of Contents
Table of Contents---------------------------------------------------------------------------------1
Notes for Safe Use-------------------------------------------------------------------------------2
Product Overview--------------------------------------------------------------------------------4
Product Characteristics--------------------------------------------------------------------------4
Technical Parameters----------------------------------------------------------------------------5
Video Parameters --------------------------------------------------------------------------------5
Optical Parameters -------------------------------------------------------------------------------6
Data Parameters ----------------------------------------------------------------------------------6
General Parameters-------------------------------------------------------------------------------7
ApplicationDrawing-----------------------------------------------------------------------------8
Panel of Optical Transmitter and Receiver ---------------------------------------------------8
LED Indicators of the Transmitter-------------------------------------------------------------9
LED Indicators of the Receiver---------------------------------------------------------------10
Note before Installation------------------------------------------------------------------------11
Installation Steps--------------------------------------------------------------------------------11
Responsibility Note-----------------------------------------------------------------------------12
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
www.questtel.com [email protected]
2
Notes for Safe Use
In order to prevent any damage to your or others’ property, please follow the
manual for safe use, although this equipment is designed reliably and safely.
1. Please read this manual carefully and keep it for your further information.
2. Please place the equipment where it will not be subjected to extreme
temperature or humidity.
3. Do not try to knot the cables of power supply or put anything on them, and
place the equipment where it will not be touched easily.
4. Please make sure the connections between power plug and other devices are
fully valid.
5. Please follow the marks on the equipment when connecting the power supply,
and the power supply should meet the following requirements:
①Input AC: AC100-240V
Input DC: -48V, -24V, -12V
②Output DC: 5V@ 2A/ 3A/ 6A/16A/20A optional
(Remark: this equipment can be used with standard power adaptor only.)
6. Please shut off the power supply immediately and contact us or your
authorized reseller when the below-mentioned happen:
①The equipment is drowned in water or other kind of liquid.
②The equipment or its shell is broken.
③The equipment works improperly.
④The equipment smells or emits noises or smoke.
7. Do not try to maintain the equipment by yourself, unless there are clear
instructions in this manual.
8. Please install special devices to prevent damages caused by lightning when
the equipment is used outdoors.
9. When the equipment is energized, please don't see optical emission port with
the naked eye.
10. While not using the machine, please wear a dust cover to protect optical
interface.
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
www.questtel.com [email protected]
4
Product Overview
QuestTel L-1SDI-SFE-TX/RX is a HD/SD-SDI over singlemode or multimode fiber
transmitter and receiver extender kit. This unit provides optical transmission of one HD/
SD-SDI signal with embedded audio signal and has reversed RS485 data channel for
camera control. The system support signals accord with standards of
SMPTE292M,SMPTE259M,SMPTE297M,SMPTE310, SMPTE305 and support digital
TV signals like DVB-ASI meeting the industrial requirements of audio and video
equipment with high performance and reliability.
The plug-and-play design makes the installation convenient and easy, the LED indicator
design helps the user to know the working status easily, and there is no need for on-site
adjustment. Signal Bit Rate from 270 Mbps to 1.5Gbps. Fiber optical transmission
excludes electromagnetic noise factor, it makes this product a perfect solution for efficient,
reliable and secured HD/SD-SDI signal transport.
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
Product Characteristics
HD/SD-SDI digital code and non-compressed HD video transmission
HD-SDI Input HD/SD-SDI, DVB-ASI - up to 1.5 Gbps Serial Digital Signal
Bandwidth ranges from 270 Mbps to 1.5Gbps
Integrated HD-SDI reclocker and cable equalizer
Embedded Audio channels
Input Signals SMPTE292M, SMPTE259M, SMPTE297M, SMPTE310, SMPTE305, DVB-ASI
LED indicators - POWER, OPTIC, SDI & RS-485 DATA
Network management function (optional)
Reverse RS485 Data (Bidirectional RS485 data and RS232 are optional)
Standalone (19U Standard 3U,4U,5.5U racks are optional)
HD-SDI video signals
In the absence of input signal, automatically shut down the laser head to extend laser life
5V DC power supply
www.questtel.com [email protected]
Technical Parameters:
Serial Video Signal BNC Input
TV Signal Standards
SMPTE292M,SMPTE259M,SMPTE297M,
SMPTE310, SMPTE305(SDTI), DVB-
ASI(EN50083-9)
Input 1 channel
Return Loss >15DB
Connector 75Ω BNC
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
Serial Video Signal BNC Output
Output
Transmitter :1-ch
Receiver: 1-ch (2-ch loop output optional);
Signal level 800mV nominal
Rise/fall time 200ps nominal
Return Loss > 15dB
Shake < 0.2UI
Connector 75Ω BNC
Optical parameters
Optical output -5～-10dBm (more optical power available)
Wave length 1310nm /1550nm
Optical Connector ST (Optional FC / LC)
Optical Receiving Sensitivity Better than -26dBm
Return Loss > 14dB
Shake < 0.2UI
Fiber core number 1 core
www.questtel.com [email protected]
6
Data Parameter
Physical Interface Terminal Block of Industrial Standard
RS485 Transmission rate 0-400 Kbps
Data Rate 0-400Kbps
Bit Error Rate <10－12
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
General Parameter
Operating Temperature -15℃~ +50℃
Storage Temperature -40~85℃
Operating Humidity 5-95%(non-condensing)
Storage Humidity 0-95%(non-condensing)
External size
114mm×60mm×30mm (Standalone)
70mm*100mm*30mm(19” 4U Rack)
Mean TimeBetween Failures ≥100,000 hours
EMI/RFI Accord with FCC Part 15 Class A, EU EMC
standards
Applications
1. Broadcast Applications
2. Connection of Sub-network for Surveillance Center
3. Public Security Surveillance
4. Highway & Toll Station Surveillance
5. Industrial Closed Circuit Television Surveillance
6. Live Events
www.questtel.com [email protected]
8
Panel of Optical Transmitter and Receiver
On the front and back panel there are Led indicators, Fiber Interfaces, Video
Interfaces (BNC), Terminal Block, Power interface.
Standard Transmission Distance: Single mode=20km; Multi mode=2km
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
Warning!
Active fiber-optic cables emit radiation invisible to the human eye.
Do not look directly at the end of an active fiber-optic cable or the
fiber connector!
www.questtel.com [email protected]
9
LED Indicators:
The difference between Optical Transmitter and Receiver is that the LED
indicators of Transmitter with Red Lights, and the LED indicators of
Receiver with Green Lights.
1) HD/SD-SDI Transmitter (Red Led Lights)
Name No light Light on Light flashes
POWER
Power is off, or
in short circuit Power is on _
OPTIC Normal working Optical barrier _
ASYNC
(Normal Optical
condition)
Effective video
signals detected Invalid video
signals _
DATA
(Normal Optical
condition)
No data
detected, or data
signal in high
electrical level
_ Effective data detected
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
www.questtel.com [email protected]
10
2) HD/SD-SDI Receiver (Green Led Lights)
Name No light Light on Light flashes
POWER
Power is off,
or in short
circuit Power is on _
OPTIC __ _
ASYNC
(Normal Optical
condition)
Effective
video signals
detected
Invalid video
signals _
DATA
(Normal Optical
condition)
No data
detected, or
data signal in
high electrical
level
_ Effective data detected
LED indicators will carry different meanings for DATA/EXT while for
customized configurations. In that case, please follow the Led Indicator
Instructions.
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
www.questtel.com [email protected]
11
Installation Instructions
1. Notes before Installation
①Five items in package, including: 1 Transmitter, 1 Receiver, Users’ Manual, 2
power Adaptors (without power adaptors when the Users self-provide Power
Supply). Please contact your seller if any one of them is missed.
②Please read this manual carefully for safe use before installation.
③Do not dismantle the device without authorization from us.
④Please check the labels on the outside of devices (Transmitter or Receiver).
⑤The optical transmitter is used to change video signals, data signals etc. into
optical signals and transmit them with optical fiber. This device can be connected
to PTZ camera.
⑥The receiver is used to receive optical signals and change them into video
signals, data signals etc..This equipment should be connected to monitors, DVRs
or matrix.
⑦The video signals out from the transmitter and into the receiver should be in
correspondence with each other, so the interfaces on the transmitter and the
receiver should be connected correspondingly.
2. Installation Procedure
①Connect the video source (camera) to the video input BNC connector on
Transmitter using coaxial cable.
②Connect the video output BNC connector on Receiver to the video monitor
using coaxial cable.
③Connect Transmitter and Receiver with the optic fiber and apply power supply
both to Transmitter and Receiver.
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
www.questtel.com [email protected]
12
Responsibility Note:
①The manufacturer will not be responsible for the damage caused to the devices
in transportation when they are returned for repair.
②Please contact the authorized seller if damages are caused to the functions or
appearances of the devices in transportation.
③If the Power Supply is self-provided, please make sure it can meet the
requirements stated in this manual, or the manufacturer will not be responsible for
the damages caused by User’s using unqualified power supply.
④Users must follow this manual in using the Power Supply.
⑤This manual or any part of it shall not be reproduced or transmitted in any form
or by any means without the manufacturer’s authorization.
⑥The manufacturer will not be responsible for any malfunction caused to the
devices or other devices or for any effect caused to human health by modifying
the devices or the User’s Manual by any means.
⑦All the packaging materials comply with the environment protection laws and
should be recycled.
SDI over Fiber User Manual
L-1SDI-SFE-TX/RX
www.questtel.com [email protected]
Read before operating equipment.
1. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
2. Power Sources - Use supplied or equivalent UL/CSA approved low voltage DC plug-in transformer.
3. Outdoor Antenna Grounding - If you connect an outside antenna or cable system to the product, be sure the antenna or cable
system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the
National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
4. Lightning - Avoid installation or reconfiguration of wiring during lightning activity.
5. Power Lines - Do not locate an outside antenna system near overhead power lines or other electric light or power circuits or where
it can fall into such power lines or circuits. When installing an outside antenna system, refrain from touching such power lines or
circuits, as contact with them might be fatal.
6. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
7. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage
points or short out parts, resulting in a fire or electric shock. Never spill liquid of any kind on the product.
8. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
9. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
When the power supply cord or plug is damaged.
If liquid spills or objects fall into the product.
If the product is exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only those controls that are
covered by the operating instructions. An improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to its normal operation.
If the video product is dropped or the cabinet is damaged.
When the video product exhibits a distinct change in performance, this indicates a need for service.
Safety Instructions
Table of contents
Other Questtel Receiver manuals
