Quicke Q-Companion BT User manual

60029456 A1
2018-09
EN SV FR
DE FI
Operator’s Manual Q-Companion BT
Original instructions - Bruksanvisning i original -
Notice originale - Original Betriebsanleitung - Alkuperäiset ohjeet
Caution!
Read through the entire instruction manual before you start to use the product.

x

328816
1
TABLE OF CONTENTS
1. OVERVIEW...............................................4
1.1. Display description......................................................4
1.1.1. USB connector........................................................4
1.2. Home screen................................................................5
1.3. Weighing view.............................................................6
1.4. Position view...............................................................7
1.5. Implement view...........................................................8
1.6. Settings view............................................................... 9
2. SETUP....................................................10
2.1. Initial setup................................................................10
2.2. Implement configuration........................................... 12
2.2.1. Add implement..................................................... 12
2.2.2. Select implement.................................................. 13
2.2.3. Rename implement............................................... 13
2.2.4. Delete implement..................................................14
2.2.5. Calibrate level position.........................................14
2.2.6. Calibrate load weighing........................................15
2.2.7. Select existing load weighing calibration.............17
2.2.8. Rename load weighing calibration....................... 17
2.2.9. Delete load weighing calibration..........................18
2.3. System settings.........................................................19
2.3.1. Loader setup......................................................... 19
2.3.2. Time and date....................................................... 20
2.3.3. Language...............................................................21
2.3.4. Backlight...............................................................21
2.3.5. Units......................................................................21
2.3.6. Factory reset......................................................... 22
2.3.7. Display name........................................................ 22
2.4. User settings.............................................................. 23
2.4.1. Rename user......................................................... 23
2.4.2. Activate user.........................................................23
2.4.3. Add user................................................................24
2.4.4. Delete user............................................................ 24
3. OPERATION...........................................25
3.1. Weighing.................................................................. 25
3.1.1. Machine requirements.......................................... 25
3.1.2. Lifting procedure.................................................. 26
3.1.3. Weighing mode.....................................................27
3.1.4. Weight presentation.............................................. 28
3.1.5. Weight accumulation............................................ 28
3.1.6. Remove last weight.............................................. 29
3.1.7. Target weight........................................................ 29
3.1.8. Tare....................................................................... 31
3.2. Position monitor.......................................................32
3.2.1. Loader height........................................................32
3.2.2. Implement angle................................................... 32
3.2.3. Lift capacity usage................................................32
3.2.4. Setpoints................................................................33
3.3. Diagnostics................................................................ 33
3.4. Maintenance reminder...............................................35
3.5. Activities....................................................................35
3.5.1. Log activities........................................................ 35
3.5.2. Export activities....................................................37
4. TROUBLE SHOOTING.......................... 38
5. ERROR CODE....................................... 40
6. CONNECTION DIAGRAM..................... 41
6.1. Mounting steps.......................................................... 41
7. WARRANTY CONDITIONS................... 42
EU Declaration of Conformity........................................42
INNEHÅLLSFÖRTECKNING
8. ÖVERSIKT..............................................43
8.1. Beskrivning av display..............................................43
8.1.1. USB-kontaktdon................................................... 43
8.2. Startsida..................................................................... 44
8.3. Vy Vägning................................................................45
8.4. Vy Position................................................................ 46
8.5. Vy Redskap................................................................47
8.6. Vy Inställningar......................................................... 48
9. INSTÄLLNING........................................49
9.1. Ursprunglig inställning..............................................49
9.2. Konfigurering av redskap..........................................51
9.2.1. Lägga till redskap................................................. 51
9.2.2. Välj redskap..........................................................52
9.2.3. Byta namn på redskap.......................................... 52
9.2.4. Ta bort redskap..................................................... 53
9.2.5. Kalibrera planläge.................................................53
9.2.6. Kalibrera lastvägning............................................54
9.2.7. Välj befintlig lastvägningskalibrering.................. 56
9.2.8. Byta namn på lastvägningskalibrering..................56
9.2.9. Radera lastvägningskalibrering.............................57
9.3. Systeminställningar.................................................. 58
9.3.1. Konfigurering av lastare.......................................58
9.3.2. Tid och datum.......................................................59
9.3.3. Språk..................................................................... 60
9.3.4. Bakgrundsbelysning..............................................60
9.3.5. Enheter.................................................................. 60
9.3.6. Fabriksåterställning...............................................61
9.3.7. Skärmnamn........................................................... 61
9.4. Användarinställningar............................................... 62
9.4.1. Byta namn på användare...................................... 62
9.4.2. Aktivera användare...............................................62
9.4.3. Lägga till användare............................................. 63
9.4.4. Ta bort användare................................................. 63
10. DRIFT................................................... 64
10.1. Vägning..................................................................64
10.1.1. Maskinkrav......................................................... 64
10.1.2. Lyftprocedur........................................................65
10.1.3. Vägningsläge.......................................................66
10.1.4. Viktvisning..........................................................67
10.1.5. Viktackumulering................................................67
10.1.6. Ta bort den senaste vikten.................................. 68
10.1.7. Målvikt................................................................68
10.1.8. Tara..................................................................... 70
10.2. Positionsmonitor.....................................................71
10.2.1. Lastarhöjd........................................................... 71
10.2.2. Redskapsvinkel................................................... 71
10.2.3. Lyftkapacitetsutnyttjande....................................71
10.2.4. Referenspunkter.................................................. 72
10.3. Diagnostik................................................................72
10.4. Underhållspåminnelse............................................. 74
10.5. Aktiviteter................................................................74
10.5.1. Loggaktiviteter....................................................74
10.5.2. Exportera aktiviteter........................................... 76

328816
2
11. FELSÖKNING.......................................77
12. FELKOD............................................... 79
13. KOPPLINGSSCHEMA......................... 80
13.1. Monteringssteg........................................................ 80
14. GARANTIBESTÄMMELSER............... 81
EU-försäkran om överensstämmelse...............................81
SOMMAIRE
15. PRÉSENTATION GÉNÉRALE............. 82
15.1. Description de l’écran............................................. 82
15.1.1. Connecteur USB................................................. 82
15.2. Écran d’accueil........................................................83
15.3. Vue Pesage.............................................................. 84
15.4. Vue Position............................................................ 85
15.5. Vue Outil................................................................. 86
15.6. Vue Paramètres........................................................87
16. INSTALLATION.................................... 88
16.1. Installation initiale...................................................88
16.2. Configuration de l’outil...........................................90
16.2.1. Ajouter un outil.................................................. 90
16.2.2. Sélectionner un outil...........................................91
16.2.3. Renommer l’outil................................................91
16.2.4. Supprimer un outil..............................................92
16.2.5. Calibrer la position horizontale.......................... 92
16.2.6. Calibrer le pesage de charges............................. 93
16.2.7. Sélectionner un calibrage de pesage
existant............................................................................ 95
16.2.8. Renommer un calibrage de pesage.....................95
16.2.9. Supprimer un calibrage de pesage......................96
16.3. Paramètres du système...........................................97
16.3.1. Configuration du chargeur..................................97
16.3.2. Heure et date.......................................................98
16.3.3. Langue................................................................ 99
16.3.4. Rétroéclairage..................................................... 99
16.3.5. Unités.................................................................. 99
16.3.6. Restaurer les paramètres d’usine...................... 100
16.3.7. Nom d’écran..................................................... 100
16.4. Paramètres de l’utilisateur.....................................101
16.4.1. Renommer l’utilisateur..................................... 101
16.4.2. Activer l’utilisateur...........................................101
16.4.3. Ajouter un utilisateur........................................102
16.4.4. Supprimer un utilisateur................................... 102
17. FONCTIONNEMENT..........................103
17.1. Pesage...................................................................103
17.1.1. Exigences requises pour la machine.................103
17.1.2. Procédure de levage..........................................104
17.1.3. Mode de pesage................................................105
17.1.4. Affichage du poids........................................... 106
17.1.5. Cumul des poids............................................... 106
17.1.6. Enlever le dernier poids....................................107
17.1.7. Poids objectif.................................................... 107
17.1.8. Tare................................................................... 109
17.2. Moniteur de position............................................110
17.2.1. Hauteur du chargeur......................................... 110
17.2.2. Angle de l’outil.................................................110
17.2.3. Utilisation de la capacité de levage.................. 110
17.2.4. Consignes..........................................................111
17.3. Diagnostics............................................................ 111
17.4. Rappel de maintenance......................................... 113
17.5. Activités.................................................................113
17.5.1. Enregistrer les activités.....................................113
17.5.2. Exporter des activités....................................... 115
18. RECHERCHE DE PANNES............... 116
19. CODE D'ERREUR..............................119
20. SCHÉMA DE RACCORDEMENT...... 121
20.1. Étapes de montage.................................................121
21. CONDITIONS DE GARANTIE........... 122
Déclaration de conformité UE...................................... 122
INHALT
22. ÜBERSICHT.......................................123
22.1. Beschreibung des Displays....................................123
22.1.1. USB-Anschluss.................................................123
22.2. Startbildschirm.......................................................124
22.3. Lastwiege-Ansicht................................................. 125
22.4. Positionsansicht..................................................... 126
22.5. Geräte-Ansicht.......................................................127
22.6. Ansicht Einstellungen............................................128
23. SETUP................................................129
23.1. Ersteinstellung....................................................... 129
23.2. Anbaugeräte-Konfiguration...................................131
23.2.1. Anbaugerät hinzufügen.....................................131
23.2.2. Anbaugerät auswählen......................................132
23.2.3. Anbaugerät umbenennen.................................. 132
23.2.4. Anbaugerät löschen.......................................... 133
23.2.5. Die horizontale Position kalibrieren................. 133
23.2.6. Lastwiegen kalibrieren......................................134
23.2.7. Eine bestehende Lastwiegekalibrierung
auswählen......................................................................136
23.2.8. Lastwiegekalibrierung umbenennen.................136
23.2.9. Lastwiegekalibrierung löschen......................... 137
23.3. Systemeinstellungen.............................................138
23.3.1. Lader Konfiguration......................................... 138
23.3.2. Uhrzeit und Datum........................................... 139
23.3.3. Sprache..............................................................140
23.3.4. Rücklicht...........................................................140
23.3.5. Einheiten........................................................... 140
23.3.6. Zurücksetzen auf Werkseinstellungen.............. 141
23.3.7. Display-Bezeichnung........................................141
23.4. Benutzereinstellungen........................................... 142
23.4.1. Benutzer umbenennen...................................... 142
23.4.2. Benutzer aktivieren...........................................142
23.4.3. Benutzer hinzufügen.........................................143
23.4.4. Benutzer löschen...............................................143
24. BETRIEB............................................ 144
24.1. Wiegen..................................................................144
24.1.1. Maschinenanforderungen..................................144
24.1.2. Hebevorgang.....................................................145
24.1.3. Wiegemodus......................................................147
24.1.4. Anzeige des Gewichts...................................... 148
24.1.5. Gewichts-Summierung..................................... 148
24.1.6. Letztes Gewicht entfernen................................149

328816
3
24.1.7. Sollgewicht....................................................... 149
24.1.8. Tara................................................................... 151
24.2. Positionsüberwachung..........................................152
24.2.1. Laderhöhe......................................................... 152
24.2.2. Winkel des Anbaugeräts...................................152
24.2.3. Ausnutzung der Hubkapazität.......................... 152
24.2.4. Sollwerte........................................................... 153
24.3. Diagnose................................................................ 153
24.4. Wartungserinnerung...............................................155
24.5. Aktivitäten............................................................. 155
24.5.1. Aktivitäten protokollieren.................................155
24.5.2. Aktivitäten exportieren..................................... 157
25. STÖRUNGSSUCHE...........................158
26. FEHLERMELDUNG........................... 161
27. ANSCHLUSSDIAGRAMM................. 163
27.1. Vorgehensweise bei der Montage..........................163
28. GARANTIEBEDINGUNGEN.............. 164
EG-Konformitätserklärung............................................164
SISÄLLYSLUETTELO
29. YLEISKUVAUS...................................165
29.1. Näytön kuvaus.......................................................165
29.1.1. USB-liitin..........................................................165
29.2. Aloitussivu.............................................................166
29.3. Punnitusnäkymä.....................................................167
29.4. Asentonäyttö..........................................................168
29.5. Työlaitenäkymä..................................................... 169
29.6. Asetusnäyttö.......................................................... 170
30. ASETUKSET...................................... 171
30.1. Alkuperäisasetus....................................................171
30.2. Työlaitteen konfigurointi.......................................173
30.2.1. Työlaitteen lisääminen...................................... 173
30.2.2. Työlaitteen valinta............................................ 174
30.2.3. Työlaitteen uudelleen nimeäminen................... 174
30.2.4. Työlaitteen poistaminen....................................175
30.2.5. Vaakatason kalibrointi...................................... 175
30.2.6. Kuormanpunnituksen kalibrointi...................... 176
30.2.7. Tämänhetkisen kuorman punnituksen
kalibrointi......................................................................178
30.2.8. Kuorman punnituksen kalibroinnin
uudelleennimeäminen................................................... 178
30.2.9. Kuorman punnituksen kalibroinnin
poistaminen...................................................................179
30.3. Järjestelmäasetukset............................................. 180
30.3.1. Kuormaimen asetukset......................................180
30.3.2. Kellonaika ja päiväys....................................... 181
30.3.3. Kieli.................................................................. 182
30.3.4. Taustavalaistus.................................................. 182
30.3.5. Yksiköt..............................................................182
30.3.6. Tehdasasetusten palauttaminen.........................183
30.3.7. Näytön nimi...................................................... 183
30.4. Käyttäjäasetukset................................................... 184
30.4.1. Käyttäjän nimeäminen uudelleen..................... 184
30.4.2. Käyttäjän aktivointi.......................................... 184
30.4.3. Käyttäjän lisääminen........................................ 185
30.4.4. Käyttäjän poistaminen...................................... 185
31. KÄYTTÖ............................................. 186
31.1. Punnitus................................................................186
31.1.1. Koneen vaatimukset..........................................186
31.1.2. Nostaminen....................................................... 187
31.1.3. Punnitustila....................................................... 188
31.1.4. Painon näyttö.................................................... 189
31.1.5. Kertynyt paino.................................................. 189
31.1.6. Viimeisimmän painon poistaminen.................. 190
31.1.7. Tavoitepaino......................................................190
31.1.8. Taaraus.............................................................. 192
31.2. Asennon valvonta.................................................193
31.2.1. Kuormaimen korkeus........................................193
31.2.2. Työlaitteen kulma............................................. 193
31.2.3. Nostokapasiteetin käyttö...................................193
31.2.4. Asetuspisteet..................................................... 194
31.3. Vianmääritys..........................................................194
31.4. Huoltomuistutus.....................................................196
31.5. Toiminnot...............................................................196
31.5.1. Lokitoiminnot................................................... 196
31.5.2. Toimintojen vienti.............................................198
32. VIANETSINTÄ....................................199
33. VIKAKOODI........................................201
34. KYTKENTÄKAAVIO...........................203
34.1. Asennusvaiheet......................................................203
35. TAKUUMÄÄRÄYKSET...................... 204
EY-vaatimustenmukaisuusvakuutus..............................204

Overview
4
1. OVERVIEW
Note. The load weighing functionality shall not be used for commercial transactions.
Q-companion is a driver support system for front loaders that helps to increase your efficiency. It features load weighing,
implement position monitoring and maintenance reminders. Q-companion BT also comes with a mobile app and web interface
for easy documentation. Download the Q-companion app free-of-charge to your mobile phone and use Bluetooth to transfer
your work results into the cloud. Q-companion can weigh the load as you lift it with the loader. The weight of the lift as well
as the accumulated results will be shown on the screen. Here you will also see the height and position of the implement, which
is useful in case you cannot see it yourself. Based on your usage of the loader, Q-companion will remind you to perform
maintenance so that your loader is kept in good condition. Taking the Q-companion system into use is straightforward.
Calibration is performed once per implement that you will use. The calibrations are stored in memory and are easily activated
when you switch implement on the loader.
Warning!
Q-Companion is an information system, NOT
a safety system. This system is designed to be a
supplementary aid when controlling the loader. It
is not, however, intended to replace the operator's
attention and judgement.
1.1. Display description
The Q-Companion is operated via the display unit. There are 4 buttons (A, B, C and D) on the display that are used for
navigation and operating functions.
When you power up Q-companion, you will be reminded of the Q-companion mobile app that is available free of charge for
iOS and Android. This startup screen will no longer appear after you have paired the Q-companion display with a mobile
phone over Bluetooth, or until the screen has been shown a certain number of times.
Fig.1 Display unit
1.1.1. USB connector
The USB connector can be used to charge your mobile phone or to update the display software.

Overview
5
1.2. Home screen
There are four main views in the user interface:
A. Weighing
B. Position
C. Implement
D. Settings
The different views can be reached from the Home screen.
Settings
Maintenance
Loader setup
Display settings
User settings
Diagnostics
Factory reset
Implements
bucket / gravel
balegrip / cal.b
fork / cal.a
New implement
79000
13
51625
kg
1575
Auto
magnus 14:56
bucket/ gravel
043
00:56:34
bucket / gravel
magnus 14:56
26
043
00:56:34
2017-09-14
bucket / gravel
magnus 14:56
00:56:34
q-c 612e
123 4 5 6
9
8 7
A
B
C
D
C
ABD
Fig.2 User interface
1.
Maintenance indicator
6.
Clock
2.
Error message indicator
7.
Active weighing calibration
3.
Loader light indicator
8.
Active implement
4.
Active user
9.
Display name
5.
Activity timer

Overview
6
1.3. Weighing view
In the Weighing view you can perform load weighing. To be able to enter the Weighing view, the selected implement has to be
calibrated for load weighing, see 2.2.6. Calibrate load weighing, as well as having its level position set, see 2.2.5. Calibrate
level position.
The weight of the load is estimated by continuously measuring the hydraulic pressure in the cylinders while inside the
weighing range during a lift cycle.
Each weighing calibration consists of two reference lifts, one with a known reference weight and the other with the implement
empty. By using two lifts, the weight can be estimated by interpolating between the two reference lifts.
00:56:34
79000
13
51625
kg
1575
Auto
magnus 14:56
bucket / gravel
031
17 16 15
1
2
3
4
5
6 7
8
9
10
11
12
13
14
Fig.3 Load weighing view
1.
Setpoints
10.
Number of added lifts
2.
Weighing range (grey filled)
11.
Target weight
3.
Loader height (0-100%)
12.
Select weighing mode
4.
Implement angle
13.
Sum
5.
Implement angle deviation
14.
Activity recording
6.
Activity timer
15.
Tare indicator
7.
Weighing mode indicator
16.
Weight
8.
Home screen
17.
Lower loader indication
9.
Setup weighing

Overview
7
1.4. Position view
In the Position view you can monitor the loader height and implement angle, as well as the capacity-usage, with regards to the
maximum system pressure.
You can also activate setpoints, to be used as position references, for both loader height and implement angle. In this view, the
loader lights (if available) can be turned on/off.
bucket / gravel
magnus 14:56
26
043
00:56:34
3
2
1
9
5
6
7
8
4
Fig.4 Position view
1.
Setpoints
6.
Configure setpoints
2.
Loader height (0-100%)
7.
Loader lights
3.
Implement angle
8.
Activity recording
4.
Activity timer
9.
Lift capacity usage (0-100 %)
5.
Home screen

Overview
8
1.5. Implement view
In the Implement view, you can configure and select which implement and weighing calibration to use while operating the
loader.
For each implement, you can configure:
- The name of the implement
- The level position for the implement
- Load weighing
Implements
bucket / gravel
balegrip / cal.b
fork / cal.a
New implement
1
2
3
4
Fig.5 Implement view
1.
Home screen
3.
Navigate down
2.
Navigate up
4.
Select

Overview
9
1.6. Settings view
In the Settings view your can view and configure different aspects of the loader and the system.
- User settings
- View errors and warnings
- View and reset maintenance reminders
- Set up the loader's basic configuration. It is
normally done at the first start-up through the
setup-wizard.
- Change the system date/time and the backlight
for the display.
- Restore the system to factory default settings
Settings
Maintenance
Loader setup
Display settings
User settings
Diagnostics
Factory reset
Settings
Maintenance
Loader setup
Display settings
User settings
Diagnostics
Factory reset
1
2
3
4
Fig.6 Settings view
1.
Home screen
3.
Navigate down
2.
Navigate up
4.
Select

Setup
10
2. SETUP
2.1. Initial setup
To be able to use the system, it needs to be properly setup. When the system is started for the first time, you are presented with
a product setup wizard that will guide you through the setup-process.
Note. Your dealer may already have performed this setup when installing the loader. In that case, the setup wizard described
here will not appear when you start the system.

Setup
11
__
Product setup
Self levelling
Non self levelling
Set loader type
Product setup
Metric (kg)
Imperial (lb)
Set units
Product setup
Set time format
24 h
12 h
Product setup
Set time
14 : 52
HH : MM
Product setup
Set date
2017 - 12 -11
YYYY - MM - DD
14:56 Product setup
Set loader to lowest position and
hold until round indicator turns green
min
14:56 Product setup
Set loader to highest position and
hold until round indicator turns green
max
14:56
Product setup
Set tool carrier to max dump position
and confirm to proceed
14:56 Product setup
Setup ready!
14:56
Product setup
Set date format
YYYY-MM-DD
MM-DD-YYYY
DD-MM-YYYY
Deutsch
Svenska
English
Français
Product setup
2. Select loader type. Confirm
with check mark.
1. Select language. Confirm with
check mark.
3. Select unit. Confirm with
check mark.
5. Adjust time. Confirm with
check mark.
4. Select time format. Confirm
with check mark.
7. Adjust date. Confirm with
check mark.
8. Hold the loader against the
mechanical stop with full joystick
deflection until indicator turns green
(3 - 4 s). Confirm with check mark.
9. Hold the loader against the
mechanical stop with full joystick
deflection until indicator turns
green (3 - 4 s). Confirm with check
mark.
6. Select date format. Confirm
with check mark.
10. Control the tool carrier to
mechanical stop and confirm with
check mark.
11. Press check mark to confirm
Fig.7 Setup

Setup
12
2.2. Implement configuration
Some configurations are specific to the active implement.Each implement needs to be calibrated, because the weight, geometry
and level position of implements vary. Also the weight lifted with different implements can vary. By having you calibrate each
implement separately, the accuracy of results produced by Q-companion is improved.
Configuration of implements is done in the Implements view. From that menu you can:
- Add an implement
- Select an implement
- Configure an implements level position
- Calibrate implement for load weighing
- Rename implement
- Delete an implement
bucket
Weighing calibrations
Calibrate level position
Select
Edit name
Delete
Implements
bucket / gravel
balegrip / cal.b
fork / cal.a
New implement
Fig.8 Implement configuration
2.2.1. Add implement
To add a new implement, go to Implement view, select New implement and press confirm. The new implement will be added to
the list.
Implements
bucket / gravel
balegrip / cal.b
fork / cal.a
New implement
Implements
bucket / gravel
balegrip / cal.b
fork / cal.a
implement1
New implement
Fig.9 Add implement

Setup
13
2.2.2. Select implement
Active implement is changed in the Implement view.
When working with Q-companion, it is important to switch the active implement (in the display) when you are changing the
implement fitted on the front loader. Selecting the implement in the display activates the correct calibrations, allowing the
implement position view and weighing view to show correct information.
Implements
bucket / gravel
balegrip / cal.b
fork / cal.a
New implement
bucket
Weighing calibrations
Calibrate level position
Select
Edit name
Delete
2. Select Select and press confirm.
1. Select which implement to activate.
Fig.10 Select implement
2.2.3. Rename implement
The name of an implement can be changed to make it easier to distinguish between different implements and their intended
usage.
Implements
bucket / gravel
balegrip / cal.b
fork / cal.a
New implement
bucket
Edit name
bucket
Weighing calibrations
Calibrate level position
Select
Edit name
Delete
bucket 2
_
3. Change name by pressing up or
down and right or left. Confirm
name by pressing right when on
the last character.
1. Select which implement to
configure.
2. Select Edit name and confirm
by pressing the check mark.
Fig.11 Rename implement

Setup
14
2.2.4. Delete implement
To delete an implement, enter Implement view and select the implement you want to delete.
Note. All the load weighing calibrations for the implement will be deleted. All the activities, as well as all the activities that
were recorded while using the implement will also be deleted, unless they are exported to the mobile app.
Implements
bucket / gravel
balegrip / cal.b
fork / cal.a
New implement
bucket
Weighing calibrations
Calibrate level position
Select
Edit name
Delete
1. Select which implement to delete and press
confirm.
2. Select Delete and press confirm.
Fig.12 Delete implement
2.2.5. Calibrate level position
The Position view and the Weighing view are depending on a correctly calibrated implement, with regards to its calibrated level
position.
To use the implement position monitoring function in the Position view and Weighing view, it is necessary to calibrate the level
position of the implement.
The level position for an implement is calibrated in the Implement view, by selecting the desired implement and then Calibrate
level position.
bucket
Set implement to level position
and confirm
Implements
bucket / gravel
balegrip / cal.b
fork / cal.a
New implement
bucket
Weighing calibrations
Calibrate level position
Select
Edit name
Delete
1. Select which implement to
configure.
3. Control the implement to its
horizontal level. Confirm by
pressing the check mark.
2. Select Calibrate level position
and confirm by pressing the
check mark.
Fig.13 Calibrate level position

Setup
15
2.2.6. Calibrate load weighing
To use the load weighing function, it is necessary to do a weighing calibration with the selected implement. The calibration
procedure is done by performing two calibration lifts. The first lift is done with a known weight in the implement and the
second lift is done with the implement empty.
Each implement used for weighing must be separately calibrated. The calibrations are stored in permanent memory.
For best accuracy, perform the calibration lifts in a similar manner as you will later work with the loader. Also consider the
following circumstances which may affect accuracy:
•Operating temperature
- Always allow the machine and
the hydraulics to warm up to the
normal operating temperature
before commencing load weighing.
•Weighing on level ground
- The tractor angle will affect the
center of gravity, hence also the
load weighing result. To achieve
the best accuracy, perform the load
weighing on level ground.
•Vehicle movement
- Weighing while the vehicle is
moving on uneven ground may
affect accuracy negatively.
•Loader arm motion
-Always use full deflection on
joystick when weighing and
make sure the lifting motion is
smooth, to avoid oscillations in the
measured pressures.
- For best accuracy, the same
engine speed should be used for
the calibration- and the actual
load weighing lifts.
•Implement angle
- It is important that the same
implement angle is used for both
the calibration lifts, as well as the
actual load weighing lifts.
The implement is calibrated for load weighing in the Implement view, by selecting the desired implement, Weighing
calibrations and then New calibration. You are guided through the calibration process. A new load weighing calibration will be
created for the selected implement.
For best accuracy, it is recommended that the known weight is equivalent to, or heavier than, the typical load that will be
weighed later.
An alternative is to use a known weight of >50% of the maximum capacity of the implement.
The minimum allowable known weight is 300 kg.
If the intent of a specific implement is to weigh the same kind of loads, with approximately the same weight, the accuracy may
increase if the known load, used during calibration, weighs as the intended loads.
Tip! If the same implement is used together with different materials, which require different handling, you can create separate
weighing calibrations for that implement.

Setup
16
New calibration
Select weighing range suitable for
the implement and confirm
STANDARD
Buckets
Silage
Forks
Bale grabs
New calibration
Successfully calibrated.
Confirm to save.
New calibration
Lift until the round indicator turns green
New calibration
Lift until the round indicator turns green
Weighing calibrations
gravel
New calibration
New calibration
Position empty implement so that
the round indicator turns green
New calibration
Enter known weight to continue
700kg
New calibration
Add a known weight and position
the implement so that the round
indicator turns green
bucket
Weighing calibrations
Calibrate level position
Select
Edit name
Delete
1. Select Weighing calibrations
and confirm with check mark.
2. Select New calibration and
confirm with check mark.
3. Select weighing range suitable
for the implement and confirm.
4. Add a known weight and
position the implement so that
the round indicator turns green.
Confirm with check mark.
5. Do a smooth lift with full
joystick deflection until the round
indicator turns green. Press check
mark when done.
6. Enter the weight of the
calibration weight. Confirm by
pressing right when on the last
digit.
8. Do a smooth lift with full
joystick deflection until the round
indicator turns green. Press check
mark when done.
9. Press check mark to confirm.
7. Empty and position the
implement so that the round
indicator turns green. Confirm
with check mark.
Fig.14 Calibrate load weighing

Setup
17
2.2.7. Select existing load weighing
calibration
To change to another load weighing calibration for the active implement, enter Implement view, select the active implement and
then Weighing calibrations. The list of available calibration is shown.
Weighing calibrations
gravel
cal.2
cal.1
New calibration
gravel
Edit name
Select
Delete
Calibrate
1. Select which calibration you want to activate.
2. Select Select and press confirm.
Fig.15 Select existing load weighing calibration
2.2.8. Rename load weighing calibration
The name of a load weighing calibration can be changed to make it easier to distinguish between the different calibrations and
their purposes.
gravel
Edit name
Weighing calibrations
gravel
cal.2
cal.1
New calibration
gravel
Edit name
Select
Delete
Calibrate
grave l
_
1. Select which calibration you
want to rename.
3. Change name by pressing up or
down and right or left. Confirm name
by pressing right when on the last
character.
2. Select Edit name and press
confirm.
Fig.16 Rename load weighing calibration

Setup
18
2.2.9. Delete load weighing calibration
To delete a load weighing calibration, enter Implement view, select the active implement and then Weighing calibrations. The
list of available calibration is shown.
Note. All the activities that were recorded while using the calibration will be deleted unless the activities are exported to the
mobile app
Weighing calibrations
gravel
cal.2
cal.1
New calibration
gravel
Edit name
Select
Delete
Calibrate
1. Select which calibration you want to delete.
2. Select Delete and press confirm.
Fig.17 Delete load weighing calibration