QuietCool IT-36003 User manual

DO NOT THROW AWAY!
OWNER’S GUIDE CONTAINS IMPORTANT INFORMATION.
LEAVE WITH HOMEOWNER
OWNER’S GUIDE
Wireless RF Control Kit
IT-36003
!

1-888-QUIETCOOL2
GENERAL SAFETY INSTRUCTIONS
1. Read Instructions - All safety and operation instructions must be read.
2. Retain Instructions - The safety and operating instructions should be kept for future
reference.
3. Heed Warnings - All warnings should be followed.
4. Follow Instructions - All installation and operating instructions should be followed.
5. Water – The QuietCool system should not be used near water. If you live in a very humid
climate, be sure to cover your damper box with insulation to reduce condensation.
6. Heat - The QuietCool system should be situated away from heat sources.
7. Damage Requiring Service - Only qualied service personnel should service the
QuietCool system. The user should not attempt to service the product.
CONTENTS
1. SYSTEM OVERVIEW..........................................3
1.1 Introduction ............................................3
1.2 Features ...............................................3
1.3 Key Specications .......................................3
2. INSTALLATION ..............................................4
2.1 Installing the Hub........................................4
2.2 Wiring the Hub. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Fan Hub LED Indicators ..................................9
2.4 Pairing the Wall Switch ..................................10
2.5 Finding a Location for the Wall Switch .....................10
2.6 Installing the Wall Switch ................................11
3. OPERATION ...............................................11
3.1 Operating the Wall Switch ...............................11
3.2 Frequently Asked Questions .............................12
RF WIRELESS CONTROL WARRANTY............................14
INCLUDED IN THE BOX
- IT-AC-HUB-01 Control Hub
- IT-RFGLSSWITCH-01 RF Switch
- QuietCool Owner’s Guide
- (2) AAA batteries
- Mounting screws and drywall
anchors
STOP! READ ALL INSTRUCTIONS IN THIS GUIDE BEFORE INSTALLING YOUR
QUIETCOOL SYSTEM
Read this guide before proceeding! The manufacturer is NOT responsible for faulty
installation or product damages caused through failure to fully read this guide BEFORE
attempting installation.
QC MANUFACTURING, INC.
26040 YNEZ ROAD
TEMECULA, CA 92591
!!
PHONE
1-888-QUIETCOOL
EMAIL
[email protected]
WEBSITE
www.QuietCoolSystems.com

QUIETCOOLSYSTEMS.COM 3
1. SYSTEM OVERVIEW
1.1 Introduction
Congratulations on the purchase of your new QuietCool RF Wireless Control!
The QuietCool Whole House Fan RF Wireless Control is the simplest way to control your
QuietCool Advanced Whole House Fan from anywhere in your home!
The QuietCool RF Wireless Control allows users to set the length of time that the fan will run
and set the desired speed level.
1.2 Features
• Control your QuietCool from anywhere in your home
• Set countdown time for each QuietCool in your home (up to 12 hours)
• Adjust speed setting for each multi-speed QuietCool
• Pair up to 20 switches to each Hub
• Surface mount wall switch that can be removed and used from anywhere in the home
1.3 KeySpecications
IT-RFGLSSWITCH-01 (Switch):
Voltage: 3VDC (2 AAA batteries)
Battery Standby Current: ≤10uA
RF working distance: 100ft (no obstructions)
IT-AC-HUB-01 (Hub)
Voltage: 120V
Frequency: 60Hz
Motor load: 1HP, 735W (Max)
UL Rated Operating Temp 14°F - 149°F
The listing of this product allows it to be installed in conned spaces with temperatures that exceed 120 degrees.

1-888-QUIETCOOL4
2. INSTALLATION
2.1 Installing the Hub
IMPORTANT: If you are installing the Hub onto an existing QuietCool fan, be sure to
shut off the power before attempting installation. If you are installing the Hub onto a
new fan, perform all installation steps before plugging in the fan.
Install the Hub directly to the motorhead:
1. Remove the handy box cover on your QuietCool fan. Remove the wire nuts from the
power cord and motor wires inside the handy box. Remove the ground screw.
2. Remove the power cord bushing and power cord. Keep both the bushing and power
cord as you will be using it for the installation of the hub.
3. Remove the four screws that are used to mount the handy box to the QuietCool
motorhead. Retain the four screws as you will be using them to attach the Hub to the
QuietCool motorhead.
4. Using your philips screwdriver, open up the Hub and install the powercord bushing
through the hole at the back of the hub.
5. Run the motor wire leads through the large knockout in the bottom of the hub.
6. Using the four screws from the handybox, mount the Hub to your QuietCool
motorhead.
2.2 Wiring the Hub
NOTE: Wiring Diagrams are for examples only. Wiring should be done by a licensed
electrician following local building and electrical codes and/or NEC guidelines. 12 or
14-gauge romex is common. Check your local building code before choosing the wire
type.
NOTE: Ensure the power is disconnected before performing any wiring connections.
NOTE: The wiring diagrams and instructions are shown using the power cord included
with your QuietCool. The installation can also be performed with 2-wire romex and
hard wired.
NOTE:IfyouareretrottingtheRFControl,youwillhavetoun-wiretheexistingwall
switch. You will reuse the power that was run to the switch to go directly into the RF
Control Hub.
Single Speed Wiring (for all 1500/1.5 models) (see Figure A)
1. Using a wire nut, connect the black wire from the power cord to the black wire
from the Hub.
!!
Installation Video:
Watch the video by scanning the
QR code or visit
www.QuietCoolSystems.com/support
!!
!!
!!
!!

QUIETCOOLSYSTEMS.COM 5
2. Connect the white wire from the power cord and the white wire on the fan to the
white wire from the Hub. Cap the yellow and red wires from the Hub.
3. FOR TRIDENT AND CLASSIC MODELS: Connect the red wire from the fan to the
blue wire on the Hub
FOR STEALTH AND ENERGY SAVER MODELS: Connect the black wire from the
fan to the blue wire on the Hub
4. Ground the green wire from the fan and the green wire from the power cord to
the ground screw in the Hub.
5. Set the dip switch positions inside the Hub as shown in the diagram below.
6. Power-on the Hub. The Power LED indicator will be lit.
7. Press the Test button to make sure the fan works. The Test LED indicator will blink
once every two seconds indicating 1-speed and the fan will be on. Press the Test
button again and the fan should shut off and the LED will be off. If the fan doesn’t
operate as described in step 6, please check the dip switch postion.
Two Speed Wiring (for CL-2250 to 7000 and TRI PRO-2.5 to 7.0) (see Figure B)
1. Using a wire nut, connect the black wire from the power cord to the black wire
from the Hub.
2. Connect the white wire from the power cord and the white wire on the fan to the
white wire from the Hub.
3. Connect the black wire from the fan to the blue wire on the Hub. Connect the red
wire from the fan to the red wire on the Hub. Cap the yellow wire from the Hub.
4. Ground the green wire from the fan and the green wire from the power cord to
the ground screw in the Hub.
Power
Cord
Attach green ground wires to ground screw
All White Common Wires Together
POWER TIMER PAIRTEST
Set dip switches:
1 - ON
2 - OFF
3 - OFF
ON
1 2 3
Whole House Fan
Figure A

1-888-QUIETCOOL6
5. Set the dip switch positions inside the Hub as shown in the diagram below.
6. Power-on the Hub. The Power LED indicator will be lit.
7. Press the Test button to make sure the fan works. The Test LED indicator will blink
twice every two seconds indicating 2-speed and the fan will be on high. Press the
Test button again and the fan will switch to low speed. Press the Test button again
and the fan should shut off and the LED will be off.
8. If the fan doesn’t operate as described in step 8, please check the dip switch
postion.
Two Speed Wiring (for ES-2250 and STL PRO-2.5) (see Figure C)
1. Using a wire nut, connect the black wire from the power cord and the black wire
from the fan to the black wire from the Hub.
2. Connect the white wire from the power cord and the white wire on the fan to the
white wire from the Hub.
3. Connect the red wire from the fan to the red wire on the Hub. Connect the yellow
wire from the fan to the blue wire on the Hub. Cap the yellow wire from the Hub.
4. Ground the green wire from the fan and the green wire from the power cord to the
ground screw in the Hub.
5. Set the dip switch positions inside the Hub as shown in the diagram.
6. Power-on the Hub. The Power LED indicator will be lit.
7. Press the Test button to make sure the fan works. The Test LED indicator will blink
twice every two seconds indicating 2-speed and the fan will be on high. Press the
Test button again and the fan will switch to low speed. Press the Test button again
and the fan should shut off and the LED will be off.
8. If the fan doesn’t operate as described in step 7, please check the dip switch
postion.
Power
Cord
Attach green ground wires to ground screw
All White Common Wires Together
POWER TIMER PAIRTEST
Set dip switches:
1 - OFF
2 - ON
3 - OFF
Whole House Fan
ON
1 2 3
Figure B

QUIETCOOLSYSTEMS.COM 7
Two Speed Wiring (for ES-3100, 4700, 5400, 6000, 7000, and STL PRO-3.3) (see Figure D)
1. Using a wire nut, connect the black wire from the power cord and the black wire
from the fan to the black wire from the Hub.
2. Connect the white wire from the power cord and the white wire on the fan to the
white wire from the Hub.
3. Connect the red wire from the fan to the red wire on the Hub. Connect the blue
wire from the fan to the blue wire on the Hub. Cap the yellow wire from the Hub.
4. Ground the green wire from the fan and the green wire from the power cord to the
ground screw in the Hub.
5. Set the dip switch positions inside the Hub as shown in the diagram below.
6. Power-on the Hub. The Power LED indicator will be lit.
7. Press the Test button to make sure the fan works. The Test LED indicator will blink
twice every two seconds indicating 2-speed and the fan will be on high. Press the
Test button again and the fan will switch to low speed. Press the Test button again
and the fan should shut off and the LED will be off.
8. If the fan doesn’t operate as described in step 7, please check the dip switch
postion
Attach green ground wires to ground screw
POWER TIMER PAIRTEST
Set dip switches:
1 - OFF
2 - ON
3 - OFF
Power
Cord
All White Common Wires Together
Whole House Fan
ON
1 2 3
Figure C
Attach green ground wires to ground screw
POWER TIMER PAIRTEST
Set dip switches:
1 - OFF
2 - ON
3 - OFF
Power
Cord
All White Common Wires Together
Whole House Fan
ON
1 2 3
Figure D

1-888-QUIETCOOL8
Three Speed Wiring (for STL PRO-4.8, 5.5, 6.0, & 7.0) (see Figure E)
1. Using a wire nut, connect the black wire from the power cord and the black wire
from the fan to the black wire from the Hub.
2. Connect the white wire from the power cord and the white wire on the fan to the
white wire from the Hub.
3. Connect the red wire from the fan to the red wire on the Hub
4. Connect the yellow wire from the fan to the yellow wire on the Hub
5. Connect the blue wire from the fan to the blue wire on the Hub
6. Ground the green wire from the fan and the green wire from the power cord to the
ground screw in the Hub.
7. Set the dip switch positions inside the Hub as shown in the diagram below.
8. Power-on the Hub. The Power LED indicator will be lit.
9. Press the Test button to make sure the fan works. The Test LED indicator will blink
three times every two seconds indicating 3-speed and the fan will be on high.
Press the Test button again and the fan will switch to medium speed. Press the Test
button again and the fan will switch to low speed. Press the Test button again and
the fan should shut off and the LED will be off.
10. If the fan doesn’t operate as described in step 9, please check the dip switch
postion.
Attach green ground wires to ground screw
POWER TIMER PAIRTEST
Set dip switches:
1 - OFF
2 - OFF
3 - ON
Power
Cord
All White Common Wires Together
Whole House Fan
ON
1 2 3
Figure E

QUIETCOOLSYSTEMS.COM 9
2.3 Fan Hub LED Indicators
Power Indicator
• The Power LED indicator will
always be lit when the Hub is
connected to Power.
• If this LED is not lit, check the
power source
Timer Indicator
• The Timer LED indicator will light
up as shown below:
1. 1 Hour: 1 Blink
2. 2 Hours: 2 Blinks
3. 4 Hours: 4 Blinks
4. 8 Hours: 8 Blinks
5. 12 Hours: 12 Blinks
6. Continuous On: Off
Test Indicator
• The Test LED indicator will light up as shown below when the Test button is pressed
and when the fan is turned on via the Wall Switch:
1. One Speed Fan: blink once every 2 seconds
2. Two Speed Fan: blink twice every 2 seconds
3. Three Speed Fan: blink three times every 2 seconds
Pair Indicator
• The Pair LED indicator will light up when making pair operations. Please see page 12
for details on pairing.
Notes on Operation
• If the Dip Switch is not congured correctly, all the indicators on the Hub will stay
solid when the Hub is powered on. Please switch off power and re-congure the Dip
Switch as shown in the wiring diagrams.
POWER TIMER PAIRTEST

1-888-QUIETCOOL10
2.4 Pairing the Wall Switch
1. Remove the mounting plate from the back of the switch and install the included AAA
batteries into the switch by removing the plastic covers. All the LED indicators will
light up indicating that the switch has power. Replace the plastic covers.
3. Press and hold the Pair button on the Hub. The Pair LED indicator will be on for three
seconds then turn off. This clears all previous pairings out of the Hub,
4. Press the Pair button on the Hub twice. The Pair LED indicator will blink once every
second indicating the Hub is in pairing mode.
5. Press any of the buttons on the Wall Switch to wake it up. Now hold one of the
buttons on the switch. The Pair LED indicator on the Hub will go out and the Wall
Switch speed indicators will be blinking indicating successful pairing. Press one of
the Wall Switch buttons again, the speed indicators will go out, and it will display the
current fan status.
6. Press the Timer button to test the Wall Switch to make sure it is communicating with
the Hub.
NOTE: If a button on the Wall Switch is not pressed within three minutes of
pressing the Pair button on the Hub, the LED indicator on the Hub will go out,
indicating unsuccessful pairing. You will need to go back and repeat steps 4 and
5.
2.5 Finding a Location for the Wall Switch
1. It is very important to nd the correct location to install the Wall Switch that will allow
the Wall Switch to communicate with the Hub.
2. Find the location you would like to install the Wall Switch and test that it properly
communicates with the fan to turn the fan on and off.
3. If the fan comes on, this is a good location.
4. If all the LED indicators turn on, the Wall Switch is not communicating with the Hub and you
will need to nd a location closer to the fan.
!!