Quoizel Inglenook TFIK8407VA Mounting instructions

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-TFIK8407VA
For Style TFIK8407VA
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
ACrossbar Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBasebulb100WMaximum,Alternatebulb(1)23WCFL.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
CFixture Body
x1
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
B
Alternate
Mounting
screw
x2
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box A
Figure 1
Mounting Screw
or Alternate Short
Mounting Screw
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
STEP 2 Test Fitting Backplate to Crossbar Assembly-
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate on Fixture Body (C) to the Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate on Fixture Body (C)
(Step 2 Continued)
should be snug against the wall and the mounting balls. If not, adjust
the length of the mounting screw or alternate short mounting screw
C
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 2
Mounting Screw
or Alternate Short
Mounting Screw
on the Crossbar Assembly
(A) by unscrewing the
preassembled hex nut and
lock washer and then
screwing the mounting
screws or alternate short
mounting screws in or out
of the crossbar until the
correct length is achieved.
Once the backplate on
Fixture Body (C) is secure,
remove the mounting ball
and Fixture Body (C) and
proceed to Step 3.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
ReleasedDate:2016-07-29

2of2
2016 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into
the outlet box and position
the backplate of Fixture Body
(C) over the outlet box. Align
the holes in the backplate
with the mounting screws or
alternate short mounting
screws. Place caulk (not
supplied) into the previously
removed mounting balls and
then attach Fixture Body (C)
using the mounting balls.
Hand tighten until snug.
C
Mounting Ball
A
Backplate
Figure 4
Mounting Screw
or Alternate Short
Mounting Screw
STEP 5 -Install Bulb and Apply Silicone Sealer
A. This fixture uses a standard bulb with medium base. Maximum 100
watts. Insert bulb and screw snugly into place.
B. Make sure exterior wall surface and fixture backplate are free of dirt
Socket
Bulb (not
Supplied)
Figure 5
Backplate
Exterior
Grade
Caulk
before applying caulk. Using
exterior grade caulk, caulk
over top of backplate and
down other side. Do not
caulk bottom of fixture
backplate to ensure proper
moisture drainage.
Your fixture is now
assembled and ready to
use. Enjoy!
TFIK8407VA
FINISH: VALIANT BRONZE
4.75” SQ.
10.5"
(1) 100W
Bulb
(Not Supplied)
Medium
Base PART NUMBER
1
NO. PART NUMBER REPLACEMENT PART QTY.
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
Fixture can
only be
mounted in
the direction
indicated
6.5"
7” SQ.
9”
1
G12946PA GLASS PANEL 3
ReleasedDate:2016-07-29