Quoizel RO9018AC User manual

Package Contents
Warnings and Cautions
1of2
For Style RO9018AC
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
markingpen,1/16”
drillbit,centerpunch,hammer,drillandwrench.
(1)A21MediumBaseBulb150WMaximum,MediumBaseVintageBulbisrecommended,bulbnotincluded.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses,
Arm
x1
C
Installation Guide #IS-RO9018AC
2018 QuoizelInc. ReleasedDate:2018-09-13
visit us on-line at www.quoizel.com
Lock Ball
x4
B
AMounting Screw
x3
D
Side Rod
x2
Fixture Body
x1
E
STEP 1 Remove Papers Inside of the Cage-
A. Rotate the bolt and remove it from the bolt holder to open the door.
B. Remove papers inside of the cage.
C. Close the door and place the bolt back onto the bolt holder.
Figure 1
STEP 2 Install Arm and Side Rods-
A. Place tabs on the ends of the Arm (D) over bolts on the Fixture
Body (E) and secure with Lock Balls (C). Hand tighten until snug.
B. Thread Side Rods (B) onto the Fixture Body (E) and hand tighten
until snug.
D
C
B
E
Tab
Bolt
Figure 2
Door
Bolt
Bolt Holder
Paper
(Remove)
STEP 3 -Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Fixture
Fitter Marking Pen
Mounting
Hole
Post
Lighting
Post
Post
Fixture
Fitter
Figure 3

2of2
2018 QuoizelInc. ReleasedDate:2018-09-13
visit us on-line at www.quoizel.com
RO9018AC
FINISH: AGED COPPER
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
17.75”
9.25”
22.75”
STEP 6 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
STEP 7 Attach the fixture to the Post Mount-
A. Place the fixture on the post lining up the mounting holes on the
fixture fitter with the holes on the post. Use the Mounting Screws (A)
to attach the fixture to the post.
Post
Hole
Fixture Fitter
Mounting Hole
Post Lighting
A
Figure 5
Figure 6
STEP 8 Install Bulb-
A. Rotate the bolt and remove it from the bolt holder to open the door.
B. Insert the bulb onto the socket and screw snugly into place.
C. Close the door and place the bolt back onto the bolt holder.
Your fixture is now assembled and ready to use. Enjoy!
Vintage Bulb
(recommended
but not included)
Socket
Door
Bolt
Bolt Holder
Figure 8
11.75”
9.25”
11.75”
STEP 4 M C
EM H
-arking the enter of
ach ounting ole
A. Remove the light fixture. Using
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
Center Punch
Hammer
Marking
Post
STEP 5 Drill Holes-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
post at each (3) locations marked in step 4 above.
1/16” bit and drill
Post
Figure 4
Figure 7