Quoizel QF5118C User manual

For Style QF5118C
Installation Guide #IS-QF5118C
1of2
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBase100WbulbMaximum,bulbnotincluded.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
Tools Required: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
A
Crossbar
Assembly
x1
B
Fixture
Body
x1
2018 QuoizelInc.
visit us on-line at www.quoizel.com
STEP 1 -Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
AFigure 1
STEP 2 Test Fitting Ceiling Canopy to
Crossbar Assembly
-
A.
Ceiling Canopy to
the
Ceiling Canopy
ceiling
Remove mounting balls from the Crossbar
Assembly (A). Fit the (D)
Crossbar Assembly (A) and secure with
mounting balls. Note: The
(D) should be snug against the and
the mounting balls. If not, adjust the length
of the nipple on the Crossbar Assembly (A)
by unscrewing the preassembled hex nut
and lock washer and then screwing the
mounting screws in or out of the crossbar
until the correct length is achieved. Once the
Ceiling Canopy (D) is secure, remove the
mounting ball and Ceiling Canopy (D) and
proceed to Step 3.
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
D
Figure 2
STEP 4 Install the Fixture-
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy (D) over the outlet box. Align the holes in the Ceiling Canopy
(D) with the mounting screws, then attach the Ceiling Canopy (D)
using the previously removed mounting balls. Hand tighten until
snug.
Figure 4
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Mounting Screw
Mounting Ball
A
D
ReleasedDate:2018-12-27

2of2
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
2018 QuoizelInc.
visit us on-line at www.quoizel.com
QF5118C
FINISH: Polished Chrome
STEP 5 - Install the Bulb
a. One of the spring clip can be opened. Find the operative sping clip to open the bottom of the cage.
b. Insert the bulb onto the socket and screw snugly into place.
c. Close the bottom of the cage and secure with the operative spring clip.
Your fixture is now assembled and ready to use. Enjoy!
Figure 5
Vintage Bulb
(recommended
but not included)
Cage
Spring clip
5” Dia.
10.5”
5.5”
5”
ReleasedDate:2018-12-27