Qvis APOIP-BL User manual

APOIP-BL
1080P WDR BULLET IP CAMERA
User’s Manual
V1.0 08 / 2013

i

ii
Welcome
Thank you for purchasing the APOIP-BL 1080P WDR BULLET.
This user’s manual is designed to be a reference tool for the installation and
operation of your system.
Here you can find information about the corresponding IP camera’s features
and functions, as well as a detailed installation method.
Before installation and operation please read the following safeguards
and warnings carefully!

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power supply shall conform to the requirement in the SELV (Safety Extra Low Voltage) and
must make sure that the limited power source is rated 12V DC or 24V AC.
Please note: Do not connect two power supplying sources to the device at the same time; it
may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation Security
Please ensure that the product does not endure heavy stresses, violent vibration or contact with
water during transportation, storage and installation.
Please use the original packing material (or the material of the same quality) if you need to return it
to vendor.
3．Installation
Do not apply power to the product before completing installation.
Do not put object(s) on the product.
Please install a proper power cut-off device during the installation connection.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers. We are not
liable for any problems caused by unauthorised modifications or attempted repair.
5. Environment
This product should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from environments that contain electromagnetic radiation or objects that
produce it.
Please keep sound ventilation around the device at all times.
Do not allow the water and other liquid to penetrate into the device if casing has been
compromised. This series product complies with the IP66 standard specified in the Degrees of
Protection Provided by Enclosure.
Ensure lightning surge protection is in place to make sure you fully protect camera circuitry from
electrical overload.

iv
Please make sure the CCD (CMOS) component is away from the radiation of the laser beam
device. Otherwise it may result in CCD (CMOS) optical component damage.
It is recommended that the grounding studs of the product should be grounded, so to further
enhance the reliability of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance
work.
Do not touch the CCD (CMOS) optic component. Please use an air jet to clean the dust off the lens
surface. You can use the dry cloth with some alcohol or mild detergent to clear if necessary.
When the camera is not in use please put the dustproof cap to protect the CCD (CMOS)
component.
Do not use volatile solvent such as the benzene, paint thinner or detergent with the ability to
abrade surfaces. It may result in lens damage or adversely affect the device’s performance.
7. Accessories
Always use all the accessories recommended by manufacturer.
Before installation, please open the package and check that all the components are included. Contact
your local retailer/vendor ASAP if something is missing.
8. Box Contents:
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
12V to 24V Conversion Cable
(For AC 24V series product only)
1
CD
1

v
Table of Contents
1General Introduction......................................................................................................1
1.1 Overview...........................................................................................................1
1.2 Features............................................................................................................1
1.3 Specifications....................................................................................................2
1.3.1 Performance...............................................................................................2
1.3.2 Factory Default Setup.................................................................................4
2Structure......................................................................................................................19
2.1 Multiple-function Combination Cable...............................................................19
2.2 Framework and Dimension.............................................................................20
2.3 Bidirectional talk..............................................................................................21
2.3.1 Device-end to PC-end...............................................................................21
2.3.2 PC-end to the Device-end.........................................................................22
2.4 Alarm Setup....................................................................................................22
3Installation ...................................................................................................................24
3.1 Device Installation...........................................................................................24
3.2 Micro SD Card Installation ..............................................................................25
3.3 Lens Adjustment .............................................................................................27
3.4 Bracket Adjustment.........................................................................................27
3.5 OSD Buttons...................................................................................................30
4Quick Configuration Tool.............................................................................................31
4.1 Overview.........................................................................................................31
4.2 Operation........................................................................................................31
5Web Operation ............................................................................................................34
5.1 Network Connection........................................................................................34
5.2 Login and Logout ............................................................................................34
6FAQ.............................................................................................................................37

© Copyright Qvis ®. All documentation rights reserved.
1
1General Introduction
1.1 Overview
This network camera integrates traditional camera and network video technology. It adopts both audio and
video data collection and transmission simultaneously. Because of inbuilt internal hardware it can connect
to a network directly without any auxiliary device. When you want to access the camera, you can use a web
browser running off the network at the client-end. Due to its multiple functions it allows for various use in
many environments such office, bank, road & traffic monitoring, etc.
This series network camera product uses the latest industry standard H.264 video and G.711a audio
compression technology, which guarantee the best audio and video quality whilst reducing file sizes.
One of the other main features this camera includes is the IR night vision, which aids in video surveillance
when the camera is functioning within a low illumination environment. The LED IRs highlight objects of
interest within the camera’s field of view and is then able to filter out any visual interference so that you can
easily view footage upon a monitor. It supports real-time monitor and listening at the same time via the
inbuilt microphone. If you want to communicate with a person(s) in view of the camera it also supports dual-
way bidirectional talk.
The built-in protection enclosure and waterproof design conforms to the IP 66 level. It has the sound
waterproof function suitable for use in the outdoor environments.
1.2 Features
User
Management
Different user rights for each group, one user belongs to one group.
The user’s right shall not exceed the group right.
Storage
Function
Supports:
Central server backup function in accordance with your configuration and
setup in alarm or schedule setting
Recording via the Web and sending the recorded file to the storage at the
client-end’s PC.
Built-in Micro SD card.
Network storage function such as FTP.
Do not support:
Local Micro SD card hot swap storage function. Only supports short-time
storage when it encounters a network disconnection.
Alarm
Function
Real-time response to external on-off alarm input, and also video detects using
user pre-defined activation setup to generate a corresponding message on
the screen and an audio prompt(the camera allows the user to pre-record the
audio file)
Real-time video detect: motion detect, camera masking.
Network
Monitor
Network camera supports one-channel audio/video data transmission to
network terminal and then decodes signal. Delay is within 270ms (network
bandwidth support needed)
Supports a maximum of 20 connections.
Adopts the following audio and video transmission protocols: HTTP, TCP,
UDP, MULTICAST, RTP/RTCP, RTSP, etc.
Supports web access.

© Copyright Qvis ®. All documentation rights reserved.
2
Network
Management
Allows network camera configuration and management via Ethernet.
Supports device management via web or client-end.
Power
External power adapter DC12V/AC 24V. You can select which power adapter
according to your actual electrical environments. Please note system cannot
support these two types of power supplying at the same time. As a
recommendation, if you wish for your security system to be continue to run
when there is a loss of power or unstable electrical supply coming from the
mains, a UPS system should be installed.
Assistant
Function
Log function
Supports system resource information and running status real-time display.
Day/Night mode auto switch.
Built-in IR light. Supports IR night vision.
Supports picture parameter setup such as electronic shutter and gain setup.
Backlight compensation: screen auto split allows backlight compensation to
adjust the brightness.
Supports video watermark function to avoid vicious video modification.
The enclosure conforms to the IP66 protection testing. It can withstand a
variety of weather conditions and outdoor environments.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification:
Parameter
System
Main Processor
TI DaVinci high performance DSP
OS
Embedded LINUX
System
Resources
Supports real-time network, local record, and remote operation at the same
time.
User Interface
Remote operation interface such as WEB & PSS
System Status
Micro SD card status, bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/2.8-inch CMOS
1/3-inch CMOS
Pixel
2080(H)*15
53(V)
1920(H)*1080(V)
2080(H)*1
553(V)
1280(H)*960(V)
Day/Night Mode
Support day/night mode switch and IR-CUT at the same time. (The lens has
built-in IR-CUT mechanical component.).
Auto Aperture
DC drive
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
On/Off
Exposure Mode
Manual/Auto
PAL: It ranges from 1/3 to 1/10000
NTSC: It ranges from 1/4 to 1/10000
Video
Compression
Standard
H.264/ H.264B/MJPEG
Video Frame
Rate
PAL: Main stream (1080P@25fps, SXGA@25fps, 1.3M@25fps,
720P@25fps, D1@25fps)
Extra stream (D1@25fps, CIF@25fps).

© Copyright Qvis ®. All documentation rights reserved.
3
NTSC: Main stream (1080P@30fps, SXGA@30fps,1.3M@30fps,
720P@30fps, 704*480@30fps)
Extra stream (704*480@30fps,352*240@30fps)
Video Bit Rate
H.264: 56Kbps-8192Kbps.
MJPEG is adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, camera masking.
Lens
Manual zoom 3.3-12
[email protected]
Motorize
d zoom
3-9
mm@F1.
2
Manual zoom 3.3-
[email protected]
Motorized
zoom 2.8-
12
[email protected]
Lens Interface
Φ14 interface. Lens is the default accessories
Audio
Audio Input
1-channel. RCA
Audio Output
1-channel. RCA
Bidirectional
Talk Input
Reuse the first audio input channel
Audio Bit Rate
16kbps 16BIT
Audio
Compression
Standard
G.711a/G.711u/PCM
Video
Motion Detect
396 (18*22) detection zones: sensitivity level ranges from 1 to 6 (The 6th
level has the highest sensitivity)
Activation event: alarm device, audio/video storage, image snapshot, log,
email function and etc.
Alarm Input
2-channel input，1-channel output
Record and Backup
Record Priority
Manual>External alarm >Video detect>Schedule
Local Storage
Support Micro SD card storage
Storage
Management
Support display local storage status
Network
Wire Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol
Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP, SMTP,
FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP.
Remote
Operation
Monitor, PTZ control, system setup, file download, log information,
maintenance , upgrade, etc.
AUX
Interface
Video Output
1-channel analog video output，BNC port.
Restore Default
Setup
Reset button
Power
Support AC24V/DC12V power. (Cannot support these two modes at the same
time.)
Genera l Parame ter
Power
Consumption
8W MAX (10W MAX when ICR switch)
Working
Temperature
-10oC~+60oC

© Copyright Qvis ®. All documentation rights reserved.
4
Working
Humidify
10%~90%
Dimensions(m
m)
φ104*306.7
Weight
1250g(Excluding box)
Installation
Bracket is included in the accessories bag.
IR Distance
20~30m
Protection
Level
IP66
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information:
Setup
Item
Default Setup
Camera
Conditions
Brightness
50
Contrast
50
Saturation
50
Sharpness
50
Anti-flicker
Outdoor
Gain Adjust
0-50
Exposure
Mode
Auto
Auto Iris
On
Scene Mode
Auto
Day/night
Mode
Auto
BLC
Off
Mirror
Off
Flip
Off
3D NR
N/A
Off
N/A
Video
Video bit stream
Main Stream
Bit stream type
General
Encode mode
H.264
Resolutio n
1080P(1920*1080)
720P(1280*720)
Frame Rate(FP S)
PAL:25
NTSC:30

© Copyright Qvis ®. All documentation rights reserved.
5
Setup
Item
Default Setup
Bit Rate Type
CBR
Recomm ended Bit
3584-8192 Kb/S
Bit Rate
8192
I Frame
50
Waterma rk
Enable
Waterma rk character
Digital CCTV
Sub Stream
Enable
Enable
Bit stream type
General
Encode mode
H.264B
Resolutio n
PAL:CIF(352*288)
NTSC:CIF(352*240)
Frame Rate(FPS )
PAL:25
NTSC:30
Bit Rate Type
CBR

© Copyright Qvis ®. All documentation rights reserved.
6
Setup
Item
Default Setup
Recomme nded Bit
192-1024Kb/S
Bit Rate
1024
I Frame
50
Snapshot
Snapshot Type
General
Image Size
1080P(1920*1080)
720P(1280*720)
Quality
Better
Interval
1s
Video Overlay
Privacy Mask
Disable
Channel Title
Enable
Time Title
Enable
Path
Snapshot Path
C:\PictureDownload
Record Path
C:\RecordDownload

© Copyright Qvis ®. All documentation rights reserved.
7
Setup
Item
Default Setup
Audio
Main Stream
Enable
Enable
Encode Mode
G.711A
Sub Stream
Enable
Disable
Encode Mode
G.711A
Network
TCP/IP
Host Name
IPC
Ethernet Card
Wire(Default)
Mode
Static
Mac Address
Device MAC address when it is shipped out of the factory
IP Version
IPV4
IP Address
192.168.1.108
Subnet Mask
255.255.255.0
Default Gateway
192.168.1.1

© Copyright Qvis ®. All documentation rights reserved.
8
Setup
Item
Default Setup
Preferred DNS
8.8.8.8
Alternate DNS
8.8.8.8
Ena
ble
ARP
/Pin
g
set
devi
ce
IP
addr
ess
serv
ice
Enable
Connection
Max Connecti on
10
TCP Port
37777
UDP Port
37778
HTTP Port
80
RTSP Port
554
HTTPS Port
443
PPPoE
Enable
Disable

© Copyright Qvis ®. All documentation rights reserved.
9
Setup
Item
Default Setup
Usernam e
none
Passwor d
N/A
DDNS
Server Type
Disable，CN99 DDNS
Server IP
none
Server Port
80
Domain Name
none
User
none
Passwor d
****
Update Period
10 minutes
IP Filter
Trusted sites
Disable
SMTP(Email)
SMTP Server
none
Port
25

© Copyright Qvis ®. All documentation rights reserved.
10
Setup
Item
Default Setup
Anonymit y
Disable
User Name
anonymity
Passwor d
****
Sender
none
Authentic ation (Encrypti on mode)
N/A
Title (Subject)
IPC Message
Attachme nt
On
Mail Receiver
N/A
Interval
0 second
Email Test
Disable，interval=60 seconds
UPnP
Enable UPnP
Disable
SNMP
SNMP v1
Disable

© Copyright Qvis ®. All documentation rights reserved.
11
Setup
Item
Default Setup
SNMP v2
Disable
SNMP v3
Disable
SNMP Port
161
Read Communi ty
public
Write Communi ty
private
Trap Address
N/A
Trap Port
162
Bonjour
Enable
Enable
Server Name
MAC
Multicast
Multicast Address
239.255.42.42
Port
36666
QoS
Real-time Monitor
0

© Copyright Qvis ®. All documentation rights reserved.
12
Setup
Item
Default Setup
Comman d
0
Event
Video detect
Motion Detect
Enable
Disable
Anti- dither
5 seconds
Sensitivit y
3
Record
Enable
Record Delay
10 seconds
Relay out
Enable
Alarm Delay
10 seconds
Send Email
Disable
Snapshot
Disable
Video Masking
Enable
Disable
Record
Enable

© Copyright Qvis ®. All documentation rights reserved.
13
Setup
Item
Default Setup
Record Delay
10 seconds
Relay out
Enable
Record Delay
10 seconds
Send Email
Disable
Snapshot
Disable
Alarm
Alarm Activation
Enable
Disable
Relay in
Alarm 1
Anti- dither
0 second
Sensor Type
NO
Record
Enable
Record Delay
10 seconds
Relay out
Enable

© Copyright Qvis ®. All documentation rights reserved.
14
Setup
Item
Default Setup
Alarm Delay
10 seconds
Send Email
Disable
Snapshot
Disable
Relay
output
1
Abnormity
No SD Card
Enable
Disable
Relay out
Enable
Relay out Delay
10 seconds
Send email
Disable
Capacity Warning
Enable
Disable
Capacity Limit
10%
Relay out
Enable
Relay out Delay
10 seconds