Qvis APOIP-MD1.3 User manual

APOIP-MD1.3
APOIP-MD2
1.3 & 2 MEGA PIXEL INTERNAL DOME IP CAMERAS
User’s Manual
V1.0 08 / 2013

i

ii
Welcome
Thank you for purchasing the 1.3 or 2 Mega Pixel Internal Dome IP
Cameras.
This user’s manual is designed to be a reference tool for the installation and
operation of your system.
Here you can find information about the corresponding IP camera’s features
and functions, as well as a detailed installation method.
Before installation and operation please read the following safeguards
and warnings carefully!

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power supply shall conform to the requirement in the SELV (Safety Extra Low Voltage) and
must make sure that the limited power source is rated 12V DC or 24V AC.
Please note: Do not connect two power supplying sources to the device at the same time; it
may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation Security
Please ensure that the product does not endure heavy stresses, violent vibration or contact with
water during transportation, storage and installation.
Please use the original packing material (or the material of the same quality) if you need to return it
to vendor.
3．Installation
Do not apply power to the product before completing installation.
Do not put object(s) on the product.
Please install a proper power cut-off device during the installation connection.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers. We are not
liable for any problems caused by unauthorised modifications or attempted repair.
5. Environment
This product should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from environments that contain electromagnetic radiation or objects that
produce it.
Please keep sound ventilation around the device at all times.
Do not allow the water and other liquid to penetrate into the device if casing has been
compromised. This series product complies with the IP66 standard specified in the Degrees of
Protection Provided by Enclosure.
Ensure lightning surge protection is in place to make sure you fully protect camera circuitry from
electrical overload.

iv
Please make sure the CCD (CMOS) component is away from the radiation of the laser beam
device. Otherwise it may result in CCD (CMOS) optical component damage.
It is recommended that the grounding studs of the product should be grounded, so to further
enhance the reliability of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance
work.
Do not touch the CCD (CMOS) optic component. Please use an air jet to clean the dust off the lens
surface. You can use the dry cloth with some alcohol or mild detergent to clear if necessary.
When the camera is not in use please put the dustproof cap to protect the CCD (CMOS)
component.
Do not use volatile solvent such as the benzene, paint thinner or detergent with the ability to
abrade surfaces. It may result in lens damage or adversely affect the device’s performance.
7. Accessories
Always use all the accessories recommended by manufacturer.
Before installation, please open the package and check that all the components are included. Contact
your local retailer/vendor ASAP if something is missing.
8. Box Contents:
Accessory Name
Amount
Network Camera Unit
1
User’s Manual
1
Installation Accessories Bag
1
CD
1

v
Table of Contents
1General Introduction......................................................................................................1
1.1 Overview...........................................................................................................1
1.2 Features............................................................................................................1
1.3 Specifications....................................................................................................2
1.3.1 Performance...............................................................................................2
1.4 Factory Default Setup .......................................................................................4
2Framework.....................................................................................................................9
2.1 Dimensions.......................................................................................................9
2.2 Structure .........................................................................................................10
3Installation ...................................................................................................................12
3.1 Device Installation...........................................................................................12
3.2 SD Card Installation........................................................................................14
4Quick Configuration Tool.............................................................................................15
4.1 Overview.........................................................................................................15
4.2 Operation........................................................................................................15
5Web Operation ............................................................................................................18
5.1 Network Connection........................................................................................18
5.2 Login and Logout ............................................................................................18
6FAQ.............................................................................................................................21

© Copyright Qvis ®. All documentation rights reserved.
1
1General Introduction
1.1 Overview
This network camera integrates traditional camera and network video technology. It adopts both audio and
video data collection and transmission simultaneously. Because of inbuilt internal hardware it can connect
to a network directly without any auxiliary device. When you want to access the camera, you can use a web
browser running off the network at the client-end. Due to its multiple functions it allows for various use in
many environments such office, bank, road & traffic monitoring, etc.
This series network camera product uses the latest industry standard H.264 video and G.711a audio
compression technology, which guarantee the best audio and video quality whilst reducing file sizes.
One of the other main features this camera includes is the IR night vision, which aids in video surveillance
when the camera is functioning within a low illumination environment. The LED IRs highlight objects of
interest within the camera’s field of view and is then able to filter out any visual interference so that you can
easily view footage upon a monitor. It supports real-time monitor and listening at the same time via the
inbuilt microphone. If you want to communicate with a person(s) in view of the camera it also supports dual-
way bidirectional talk.
The built-in protection enclosure and waterproof design conforms to the IP 66 level. It has the sound
waterproof function suitable for use in the outdoor environments.
1.2 Features
User
Management
Different user rights for each group, one user belongs to one group.
The user’s right shall not exceed the group right.
Storage
Function
Supports:
Central server backup function in accordance with your configuration and
setup in alarm or schedule setting
Recording via the Web and sending the recorded file to the storage at the
client-end’s PC.
Network storage function such as FTP.
Alarm
Function
Real-time response to external on-off alarm input, and also video detects using
user pre-defined activation setup to generate a corresponding message on
the screen and an audio prompt(the camera allows the user to pre-record the
audio file)
Real-time video detect: motion detect, camera masking.
Network
Monitor
Network camera supports one-channel audio/video data transmission to
network terminal and then decodes signal. Delay is within 270ms (network
bandwidth support needed)
Supports a maximum of 20 connections.
Adopts the following audio and video transmission protocols: HTTP, TCP,
UDP, MULTICAST, RTP/RTCP, RTSP, etc.
Supports web access.
Network
Management
Allows network camera configuration and management via Ethernet.
Supports device management via web or client-end.
Power
External power adapter DC12V.
Supports s PoE supply

© Copyright Qvis ®. All documentation rights reserved.
2
Warning！
Do not connect these two power supplying sources to the device at the same
time; it may result in device damage!
Please note: system cannot support these two types of power supplying at the same
time. As a recommendation, if you wish for your security system to be continue to run
when there is a loss of power or unstable electrical supply coming from the mains, a
UPS system should be installed.
Assistant
Function
Log function
Supports system resource information and running status real-time display.
Day/Night mode auto switch.
Supports picture parameter setup such as electronic shutter and gain setup.
Backlight compensation: screen auto split allows backlight compensation to
adjust the brightness.
Supports video watermark function to avoid vicious video modification.
The enclosure conforms to the IP66 protection testing. It can withstand a
variety of weather conditions and outdoor environments.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification:
Model
Parameter
APOIP-EYE1.3
APOIP-EYE2
System
Main Processor
TI Davinci high performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3-inch CMOS
1/2.-inch CMOS
Pixel
1280(H)x960(V)
1920(H) x 1080(V)
Day/night
Support day/night mode switch.
Gain Control
Fixed/Auto
BLC
On/Off
White Balance
Manual/Auto
Electronic
Shutter
Manual/Auto
PAL: It ranges from 1/3 to 1/10000
NTSC: It ranges from 1/4 to 1/10000
Video
Compression
Standard
H.264/JPEG/MJPEG

© Copyright Qvis ®. All documentation rights reserved.
3
Video Frame
Rate
PAL:
Main stream: (1280x960@15fps)
Extra stream: (704×576) or
(352×288) @ 25fps
PAL:
Main stream(1920*1080@25fps),
extra stream,(704*576@25fps)
NTFC:
Main stream: 1280x960@15fps)
Extra stream: (704×576) or
(352×288) @ 25fps
NTSC:
Main stream(1920*1080@30fps),
extra stream,(704*576@30fps)
Video Bit Rate
48k~8192kbps
Bit rate is adjustable.
Support customised setup.
Video Flip
Support mirror.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, camera masking.
Lens
3.6mm Fixed
3.6mm Fixed
Lens Interface
M12. Default lens
Video
Motion Detect
396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The
6th level has the highest sensitivity)
Activation event: video storage, image snapshot, log, email function
and etc.
Record and Backup
Record Priority
Manual>External alarm >Video detect>Schedule
Storage
Management
Support FTP storage.
Network
Wire Network
1-ch 10/100 M Ethernet, RJ45 port
Network Protocol
HTTP, TCP/IP, ARP, RTSP, RTP,UDP, RTCP, SMTP, FTP, DHCP,
DNS, DDNS, PPPOE, IPv4/6, SNMP, UPNP, NTP
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc
Restore Default
Setup
Built-in Reset button
General Parameter
Power
DC12V power and PoE.
Warning！
Do not connect these two power supplying sources to the device
at the same time; it may result in device damage!
Power
Consumption
4.5W MAX
Working
Temperature
-10oC ~+60oC
Working
Humidify
10%~90%
Dimensions(mm)
Φ110×54
Weight
250g(Excluding box)
400g (Excluding box)
Installation
Fixed on the wall, ceiling, etc.

© Copyright Qvis ®. All documentation rights reserved.
4
1.4 Factory Default Setup
Please refer to the following sheet for factory default setup information:
Setup
Item
Default Setup
APOIP-EYE1.3
APOIP-EYE2
Camera
Conditions
Brightness
50
Contrast
50
Sharpness
50
Saturation
50
Exposure mode
Auto
Gain Mode
Auto
Gain Limit
80
Scene Mode
Auto
Day/night Mode
Auto
BLC
Off
Mirror
Disabled
Flip
Disabled
Video
Video bit stream
Main
Stream
Bit stream type
General
Encode mode
H.264
Resolution
720P (1280x96)
1080P(1920x1080)
Frame
Rate(FPS)
PAL: 25
NTSC:30
Bit Rate Type
CBR
Recommende
d Bit
3584-8192 Kb/S
Bit Rate
8192
I Frame
interval
50
Watermark
Enable
Watermark
character
DigitalCCTV
Sub
Stream
Enable
Enable
Bit stream
type
General
Encode mode
H.264B
Resolution
CIF(352*288)
Frame
Rate(FPS)
PAL: 25
NTSC:30
Bit Rate Type
CBR
Recommende
d Bit
192-1024Kb/S
Bit Rate
1024

© Copyright Qvis ®. All documentation rights reserved.
5
Setup
Item
Default Setup
APOIP-EYE1.3
APOIP-EYE2
I Frame
interval
50
Snapshot
Snapshot
Type
General
Image Size
720P (1280x96)
1080P(1920x1080)
Quality
Better
Interval
1s
Video Overlay
Privacy Mask
Disable
Channel Title
Enable
Time Title
Enable
Path
Snapshot Path
C:\PictureDownload
Record Path
C:\RecordDownload
Network
TCP/IP
Host Name
IPC
Ethernet Card
Wire(Default)
Mode
Static
Mac Address
Default
IP Version
IPV4
IP Address
192.168.1.108
Subnet Mask
255.255.255.0
Default
Gateway
192.168.1.1
Preferred DNS
8.8.8.8
Alternate DNS
8.8.8.8
Enable
ARP/Ping set
device IP
address
service
Enable
Connection
Max
Connection
10
TCP Port
37777
UDP Port
37778
HTTP Port
80
RTSP Port
554
Enable HTTP
Disable
HTTPs Port
443
PPPoE
Enable
Disable
Username
none
Password
N/A
DDNS
Server Type
Disable，CN99 DDNS
Server IP
none

© Copyright Qvis ®. All documentation rights reserved.
6
Setup
Item
Default Setup
APOIP-EYE1.3
APOIP-EYE2
Server Port
80
Domain Name
none
User
none
Password
N/A
Update Period
5 minutes
IP Filter
Trusted sites
Disable
SMTP(Email)
SMTP Server
none
Port
25
Anonymity
Disable
User Name
anonymity
Password
N/A
Sender
none
Authentication
(Encryption
mode)
N/A
Title (Subject)
IPC Message
Attachment
N/A
Mail Receiver
0 seconds
Email Test
Disable，interval=60 seconds
UPnP
Enable UPnP
Disable
SNMP
SNMP Port
161
Read
Community
public
Write
Community
private
Trap Address
N/A
Trap Port
162
SNMP Version
‘Device name+SN’. Depends on the device.
Bonjour
Enable
Enable
Server Name
Device factory SN
Multicast
Multicast
Address
239.255.42.42
Port
36666
Auto Register
Enable
Disable
SN
1
Server IP
0.0.0.0
Port
7000
Sub-device ID
None

© Copyright Qvis ®. All documentation rights reserved.
7
Setup
Item
Default Setup
APOIP-EYE1.3
APOIP-EYE2
WIFI
ON(Enable)
Enable
QoS
Real-time
Monitor
0
Command
0
Event
Video detect
Motion Detect
Enable
Disabled
Anti-dither
5 seconds
Sensitivity
3
Record
Channel
Enable
Record Delay
10 seconds
Send Email
Disable
Snapshot
Disabled
Video
Masking
Enable
Disabled
Record
Channel
Enable
Record Delay
10 seconds
Send Email
Disable
Snapshot
Disabled
Abnormity
Disconnection
Enable
Disabled
Record
Enable
Record Delay
10s
IP Conflict
Enable
Disabled
Record
Enabled
Record Delay
10s
Storage
Storage
FTP
Enable FTP
Disable
Server IP
N/A
Port
21
Username
anonymity
Password
N/A
Remote path
share
Emergency
(Local)
Disable
Record Control
Pack Duration
8 minutes
Pre-record
5 seconds
Disk Full
Overwrite
Record Mode
Auto
System
General
Local Host
Device No
Device MAC address
Language
English
Video
Standard
PAL/NTSC
Date and time
Date Format
Y-M-D

© Copyright Qvis ®. All documentation rights reserved.
8
Setup
Item
Default Setup
APOIP-EYE1.3
APOIP-EYE2
Time Format
24H
Time Zone
GMT+08:00
System Time
Sync
DST
Disable
DST Type
Week
Start Time
00:00:00 of the first Sunday of the month
End Time
00:00:00 of the second Monday of the month
NTP
Disable
NTP Server
clock.isc.org
Port
37
Update Period
10 minutes
Auto Maintenance
Auto Reboot
Enable
Auto Delete
Old Files
Disable

© Copyright Qvis ®. All documentation rights reserved.
9
2Framework
2.1 Dimensions
Please refer to the following figure for the dimension information. The unit is mm. See
Figure 2-1 and Figure 2-3.
Figure 2-1
Figure 2-2

© Copyright Qvis ®. All documentation rights reserved.
10
Figure 2-3
2.2 Structure
Please refer to the following figure for detailed information (see Figure 2-4).
Figure 2-4

© Copyright Qvis ®. All documentation rights reserved.
11
Please refer to the following sheet for detailed information.
SN
Name
1
X-Y-Z rotation module
2
Device lens
3
Dome camera enclosure
SN
Name
Function
4
Power input port
Connect to the DC 12+ power to
input the power.
5
Network port
Network data input, output and
PoE.

© Copyright Qvis ®. All documentation rights reserved.
12
3Installation
3.1 Device Installation
This series network camera can be put on the table to install for surveillance. You can also use the bracket
or the in-ceiling installation if you require the hang function. Please refer to the steps listed below.
Figure 3-1
Figure 3-2
Step1
Use the inner hexagonal wrench (provided) to loosen the three inner hexagon screws in the dome cover
and then open the cover.
Step 2
Please take out the installation position map in the accessories bag, and then paste it on the ceiling or the
wall according to your monitor area requirements. Draw and then dig three plastic expansion bolts holes in
the installation surface and then insert three expansion bolts in the holes. Secure these three bolts firmly.
Please dig a ‘cable exit hole’in the surface according to the installation position map if you want to draw out
the cable from the top of the installation surface. You need to use the proper tool to open up the side port of
the U-cable channel of the dome camera pedestal if you want to draw out the cable from the side port of

© Copyright Qvis ®. All documentation rights reserved.
13
the cable channel when you are installing the device cable. And then you can draw out the cable from the
cable channel of the pedestal.
Step 3
Adjust the device installation pedestal to the proper position and then draw the cable through the cable exit
you just dug in the ceiling (wall). Line up the TOP direction of the device to the installation position map and
then line up the three screw holes in the device pedestal to the three plastic expansion bolt holes in the
installation position. Put the three self-tapping screws in the three plastic expansion bolts firmly. Now the
dome camera is secure in the installation surface.
Step 4
Loosen the two M3 secure screws of the lens rotation structure (Do not remove; it will be OK to loosen a
little bit). Use the inner hexagonal wrench to insert them to the inner hexagonal holes and then use the
wrench to turn the lens. Adjust the lens to the proper monitor angle and then secure the screws of the lens
rotation structure. The lens adjust angle ranges are: flip (0°~+75°), video pan rotation (-15°~+15°) ,
video rotation angle(-15°~+15°).
Step 5
Line up the dome camera cover to the cable exits and put the cover back. Use the inner hexagonal wrench
to secure the three inner hexagonal screws firmly. Now the installation completed.
Note:
The device GND cable can effectively enhance the device reliability. The GND hole is near the cable exit of
the back of the enclosure. The GND screw specification is M3 (see Figure 3-3).
Figure 3-3

© Copyright Qvis ®. All documentation rights reserved.
14
3.2 SD Card Installation
Important
Some series product do not support the SD card storage function.
Please shut down the power and then turn off the device before you install the SD card.
Step 1
Please refer to the Step 1 in Chapter 2.1 to open the device.
Step 2
Find the ‘SD CARD’indicator in the enclosure. Adjust the SD card to the proper direction and then install
(see Figure 3-4).
Step 3
Please refer to the Step 5 in Chapter 2.1 to complete the installation.
Figure 3-4