QwikSwitch QS-R-DOPTO User manual

Features
• QS-R-DOPTO is the most popular unit in the QwikSwitch Range, having the
ability to change to a dimmer or a relay receiver.
• Default Mode: ON/OFF - Mode needs to be set at installation.
• Please consult the QwikSwitch Website for a list of tested compatible LED’s.
• This device is controllable from the WiFi Bridge (QS-WIFI-BRIDGE) remotely
- Set schedules - Turn on / off devices - Device Status
• Not to be used for CFL Dimming - Can switch CFL ON/OFF (Relay Mode)
Specifications
• Input - 230 Vac, 50Hz
• Max Output - 1A (Relay Mode) / 200W (Dimmer Mode)
• Form Factor - Moulded casing - 86mm (L) x 36mm (W) x 29mm (H)
• Radio Frequency - 868 Mhz
• Range - 30m through walls and floors, 100m line of sight.
• Repeaters (QS-T-REP) available if needed.
Relay
MAX 1A
(Switched Output)
1A
Dimmer
Note: Neutral to the load may be
supplied from the receiver or
from the neutral run in the ceiling
1A
200W/1A Multi Function Receiver
QS-R-DOPTO
QS-R-DOPTO
DIMMER
RECEIVER
LED/
HALOGEN LEADING
EDGE
10W
x20 SWITCH
1A
Dimming or ON/OFF in
one unit!
230V AC 50Hz
(Mains supply)
www.qwikswitch.co.za

Test/Link Button
LED
Note: Always install
so that the
TEST/LINK BUTTON
is accessible
Mode 1: Linking to a transmiter.
Hold the ”Link” button for approximately 3 seconds or unl the LED starts flashing (medium rate),
then press the desired transmiter buon to be linked.
Confirmaon of linking will be indicated with 3 flashes.
Mode 2: Set OFF level (LED dimming stop/off level)
Note 1: Mode 2 seng is only equired when using the unit to dim an LED load, this allows you
to stop and switch off the LED dimming at a level higher than 0.
Note 2: Before changing Mode 2, first ensure that you have set the unit to be a dimmer (as per
Mode 3 explanaon)
Note 3: Before changing Mode 2, first link the unit to a trransmier (as per Mode 1 explananaon)
Acon:
1: Set the light level that you require the LED to switch o ffat, using the linked trransmier.
2: Hold the ”Link” buton for approximately 5 seconds or unl the LED flashes at a fast rate, then
release the buton.
3: To clear this level and reset it to “0”, repeat step 2.
Mode 3: Choose between Relay (ON/OFF) and DIM mode.
1: Hold the buton for approximately 8 seconds or unnl the LED flashes at slow rate, then
release the buton. The unit will now change mode from ON/OFF to DIM mode or visa-versa.
2: Repeat step 1 to revert to the alternate mode. (DIM changes to ON/OFF & ON/OFF changes to
DIM)
Mode 4: Clear all sengs and reset to default mode.
Default (ON/OFF)
Hold the button for approximately 10 seconds or unl the LED is permantly on, then release the
button. All seng will now be closed and returned to default.
Please note: If the mode is changed between DIM and ON/OFF, the device will need to be deleted
and then re-added to the app or online interface.
QS-R-DOPTO
DIMMER
RECEIVER
LED/
HALOGEN LEADING
EDGE
10W
x20 SWITCH
1A
200W/1A Multi Function Receiver
QS-R-DOPTO
200W/1A Multi Function Receiver
QS-R-DOPTO
www.qwikswitch.co.za