Race Face VAULT 30 User manual

1
605-00-239 REV A
SEATPOST OWNER’S GUIDE
RACEFACE.COM
PARTS LIST
*Bearings are sold in single (1) qty. Purchase 2 to replace both bearings.
NOTE: Some Race Face and Easton spare parts can be interchanged as necessary, see Parts List Appendix A
TOOL AND SUPPLIES LIST FOR ALL SERVICE STEPS
Small flat head screwdriver or pick
Small plastic mallet
Bearing press
VAULT 34 (or Park Tool Drift 2262-2 / 2272-2)
VAULT 35 (or Park Tool Drift 2262-2 / 2272-2)
VAULT 33
VAULT 32 (x2)
Rubber gloves
Clean, lint-free rags
15 mm or 12 mm blind bearing puller or vise with soft jaws (optional)
APPROVED GREASES AND OIL FOR ALL SERVICE STEPS
Easton Cassette Body Grease
Buzzy’s Slick Honey Grease
Slickoleum Light Grease
Dumonde Tech Classic Freehub Grease
Dumonde Tech Advanced Freehub Grease
Superlube Silicone Lubricating Grease
Triflow Clear Synthetic Grease
WATERPROOF GREASE
Any thick waterproof, marine grease
OIL
Super Lube Multi Purpose Synthetic Oil With Syncolon (PTFE)
Park Tool CL-1 Synthetic Blend Lube With PTFE
Similar light PTFE oil
TRACE HUB SERVICE MANUAL
The instructions in this service manual can be used with the parts listed below. If you do not see your parts listed here, please
contact your dealer for instructions and information.
RACE FACE TRACE FRONT HUBS RACE FACE TRACE REAR HUBS
HUB MODEL FRONT HUBS: J615
Aeect R Front wheels, Aftermarket Hub F60199
REAR HUBS: J624/J622
Aeect R and Aeect R eMTB Rear wheels, Aftermarket Hubs F60190,
F60191, F60192, F60193, F60194, F60195
BEARINGS (REQUIRED) * 2x - F60123, BEARING, 18X30, CN, AM * 2x - F60078, BEARING, 6902 CM
AXLE (OPTIONAL) F60202, AXLE, TRACE, J-BEND, FRONT, 15x110
(J615)
F60200, AXLE, TRACE, J-BEND, REAR, 12x148 (J624)
F60201, AXLE, TRACE, J-BEND, REAR, 12x157 (J622)
OTHER PARTS TO REVIEW FOR
REPLACING (OPTIONAL)
F60199, ENDCAP, SET, TRACE, J-BEND, FRONT,
15X110
F60196, ENDCAP, SET, TRACE, J-BEND, REAR, 12X148/157
F60203, SPACER, TRACE, J-BEND, CASSETTE BODY
F60204, SEAL, TRACE, J-BEND, CASSETTE BODY, NDS
PART DESCRIPTION QTY SUPPLIED IN KIT TRACE HUB COMPATIBILITY
VAULT 30 Bearing removal tool, 6805 1 *N/A
VAULT 31 Bearing installation drift, 6805 2 *N/A
VAULT 32 Bearing installation drift, 18x30 2 J615
VAULT 33 Bearing removal tool, 18x30 1 J615
VAULT 34 Bearing installation drift, 6902 drive side 1 J624/J622
VAULT 35 Bearing installation drift, 6902 non-drive side 1 J624/J622
*For use in VAULT hubs only
Kit parts are laser etched to help you identify them easily. Visit raceface.com for more information on how to use this kit to service
Trace hubs and VAULT hubs.
Race Face products should be installed by a professional bicycle service technician, in
accordance with Race Face installation specifications. Improperly installed products
can fail, causing the rider to lose control resulting in SEVERE INJURY OR DEATH.
Modification or alteration of a Race Face product can cause product failure resulting
in SEVERE INJURY OR DEATH.
Improper service, or use of non-Race Face replacement parts with Race Face products
may cause the product to malfunction, resulting in SEVERE INJURY OR DEATH.
Never use a power washer to clean your Race Face product.
VAULT KIT (F60185) CONTENTS:
WARNING AND SAFETY INFORMATION

2
TRACE FRONT HUB BEARING REPLACEMENT (J615)
PART LIST
F60123, BEARING, 18X30, CN, AM (1 PC) - 2 REQUIRED FOR SERVICE
F60202, AXLE, TRACE, J-BEND, FRONT, 15x110 (J615)
TOOL LIST
Plastic mallet
Pick or small flat head screwdriver
Bearing press
VAULT 33
VAULT 32 (x2)
15 mm blind bearing puller or vise with soft jaws (optional)
Rubber gloves
FRONT BEARING REMOVAL
1. Remove the end caps.
NOTICE: All Race Face end caps are designed to be removed by hand. Clamping end caps with vise jaws or pliers can damage
them. A rubber glove can help improve grip. A 15 mm blind bearing puller tool can be used for dicult to remove end caps.
2. Insert the VAULT 33 removal drift into the rotor side of the axle.
3. Use the mallet to tap the removal drift until the non-rotor side bearing is ejected. Remove the drift and discard the bearing.
4. Keep the axle inserted into the rotor-side bearing. Insert the VAULT 33 removal drift into the non-rotor side and use the mallet
to tap the drift until the rotor-side bearing and seal are ejected. Remove all tools, set the seal aside, and discard the bearing.
5. Clean and inspect all parts for signs of damage and wear, including the hub shell, axle, end caps, and seals. Check the seal for
tears or worn edges. Use a flathead screwdriver or pick to remove and replace the seal if it is damaged.
FRONT BEARING INSTALLATION
IMPORTANT: Always fully install the rotor-side bearing first for front hubs.
1. Apply a light coat of WATERPROOF GREASE to the axle bearing surfaces.
2. Install the new 18x30 bearing onto the end of the axle, making sure the red seal is facing out. Insert the VAULT 32 onto the
axle with the flat side contacting the bearing. Install the bearing/axle/drift assembly into the rotor-side bearing bore.
IMPORTANT: Never press a bearing using the stepped side of a bearing drift. Only press bearings with the flat side of the drift
contacting the bearings.
IMPORTANT: Do not apply grease or Loctite to the bearing bores.
3. Insert the second VAULT 32 into the non-rotor side bearing bore. Make sure the counter-bore side is facing in toward the axle
flange.
4. Insert the bearing press through the drifts and tighten until the rotor-side bearing is firmly seated.
IMPORTANT: Use a moderate force on the handles of bearing press. Forces too low or too high can result in excessive drag
and premature wear.
5. Remove the press from the non-rotor side and leave all other parts in place.
6. Position the bearing on the axle of the non-rotor side and make sure the red seal is facing out.
7. Install the VAULT 32 onto the axle against the non-rotor side bearings. Make sure the flat side of the VAULT 32 is facing
inward. Both VAULT 32 tools must now be contacting the bearings on both the rotor and non-rotor side.
NOTE: Original bearings have black bearing seals on both sides. Replacement bearings are VAULT bearings used in Trace hubs
and the red seals should face out.
8. Insert the bearing press and tighten until low force bottom out.
9. Make sure the axle rotates smoothly. If the axle has resistance or roughness, review the bearing press alignment and
determine if this force is too high or too low. Consult your dealer for any questions or assistance in troubleshooting.
10. Apply an even coat of WATERPROOF GREASE to the outsides of both bearings.
11. Reinstall the end caps by hand.
NOTE: The front end caps are symmetrical.

3
TRACE REAR HUB BEARING REPLACEMENT (J624/J622)
PART LIST
2x F60078: BEARING, 6902 CM
F60201, AXLE, TRACE, J-BEND, REAR, 12x148 (J624) or F60200, AXLE, TRACE, J-BEND, REAR, 12x157 (J622)
F60204, SEAL, TRACE, J-BEND, CASSETTE BODY, NDS
TOOL LIST
Plastic mallet
Small flat head screwdriver or pick
Bearing press
VAULT 34 (or Park Tool Drift 2262-2 / 2272-2)
VAULT 35 (or Park Tool Drift 2262-2 / 2272-2)
12 mm blind bearing puller or vise with soft jaws (optional)
Lint-free rag
Rubber gloves
REAR BEARING REMOVAL
1. Remove the drive side end cap and cassette body by firmly gripping and pulling the
cassette body
NOTICE: All Race Face end caps are designed to be removed by hand. Clamping end caps with vise jaws or pliers can damage them. A
rubber glove can help improve grip. A 12 mm blind bearing puller tool can be used for dicult to remove end caps.
2. Remove the cassette body 12.55 mm spacer.
TIP: This spacer can be located on the axle against the drive side hub shell bearing OR it can stick to the inner cassette body bearing
inner race.
3. Use a mallet to tap the drive-side end of the axle to eject the bearing and axle from the non-drive side.
4. Remove the non-drive side end cap, if it is not already removed. Remove the non-drive side seal and bearing from the axle. Set the seal
aside and discard the bearing.
5. Turn the axle around and insert the non-drive end of the axle into the drive side bearing. Use a mallet to tap the axle and eject the
bearing from the drive side. Remove the axle and discard the bearing.
6. Clean and inspect all parts for signs of damage and wear, including the hub shell, axle, cassette body, and seals. Check the cassette body
seal lip and non-drive side seal for tears or worn edges. Use a flathead screwdriver or pick to remove and replace the seals if they are
damaged.
REAR BEARING REPLACEMENT
IMPORTANT: Always fully install the rear drive-side bearing first for rear hubs.
1. Apply a light coat of WATERPROOF GREASE to the axle bearing surfaces.
2. Slide the bearing onto the drive side of the axle with the red seal facing out. Add the VAULT 34 onto the axle/bearing assembly. Insert
the axle/bearing/drift assembly into the drive side bearing bore.
IMPORTANT: Install/press only one bearing at a time.
3. Insert the VAULT 35 into the non-drive side bearing bore with the stepped side facing in.
4. Insert the bearing press through the hub, all drifts, axle, and bearing. Tighten the press until the bearing is fully installed.
IMPORTANT: Use a moderate force on the handles of the bearing press. Forces too low or too high can result in excessive drag and
premature wear.
5. Remove the press from the non-drive side.
6. Slide the non-drive side bearing onto the axle with the red seal facing out.
7. Place the flat side of the VAULT 35 against the bearing.
8. Assemble the press, ensure all drifts are aligned, and tighten with low force until the non-drive side bearing is fully installed.
9. Remove the press and drifts.
10. Make sure the axle rotates smoothly. If the axle has resistance or roughness, review the bearing press alignment and determine if this
force is too high or too low. Consult your dealer for any questions or assistance in troubleshooting.
REAR HUB FINAL ASSEMBLY
1. Apply a small and even coat of LIGHT CASSETTE BODY GREASE to the non-drive side bearing face.
2. Apply LIGHT CASSETTE BODY GREASE to the inner lip of the non-drive side end cap seal. Install the seal into the non-drive side hub
shell bore with the sealing lip edge facing out. Use VAULT 34 or VAULT 35 to fully seat the non-drive side end cap seal.
3. Install the non-drive side end cap.
4. Install the cassette body 12.55 mm spacer onto the axle.
5. Grease the hub shell drive ring with a moderate layer of LIGHT CASSETTE BODY GREASE.
6. Apply OIL inside the cassette body seal lip.
7. For Shimano HG and XD cassette bodies only: Apply a thin coat of LIGHT CASSETTE BODY GREASE to inside of seal lip at the outer
cassette body bearing.
8. Slide the cassette body onto the axle. Make sure to rotate the cassette body counter-clockwise to disengage the pawls and allow the
cassette body to fully seat.
9. For Micro Spline cassette bodies only: Apply a thin coat of WATERPROOF GREASE to the outer cassette body bearing, then install the
thin steel washer.
10. Install the correct end cap onto the axle, according to your cassette body specification:
Shimano HG and XD: Install the 17.5mm long end cap, which has no logo.
Micro Spline: Install the 19.3mm long end cap, which has the Micro Spline logo.

4
CASSETTE BODY REPLACEMENT (J624/J622)
This cassette body replacement procedure is only for the cassette bodies listed in the parts list below.
PART LIST
F60190: CASSETTE BODY, TRACE. J-BEND, MTN-HG, ALLOY
F60191: CASSETTE BODY, TRACE. J-BEND, MTN-HG, STEEL
F60192: CASSETTE BODY, TRACE. J-BEND, XD, ALLOY
F60193: CASSETTE BODY, TRACE. J-BEND, XD, STEEL
F60194: CASSETTE BODY, TRACE. J-BEND, MS, ALLOY
F60195: CASSETTE BODY, TRACE. J-BEND, MS, STEEL
TOOL LIST
Plastic mallet
12 mm blind bearing puller or vise with soft jaws (optional)
Rubber gloves
REMOVAL
1. Firmly pull the end cap and cassette body by hand to remove them.
NOTICE: All Race Face end caps are designed to be removed by hand. Clamping end caps with vise jaws or
pliers can damage them. A rubber glove can help improve grip. A 15 mm or 12 mm blind bearing puller tool
can be used for dicult to remove end caps.
2. Remove the cassette body 12.55 mm spacer.
TIP: This spacer can be located on the axle against the drive side hub shell bearing OR it can stick to the inner
cassette body bearing inner race.
INSTALLATION
1. Apply LIGHT OIL to the cassette body seal inner lip.
2. Install the cassette body 12.55 mm spacer onto the axle.
3. Grease the hub shell drive ring with a moderate layer of LIGHT CASSETTE BODY GREASE.
Shimano HG and XD cassette bodies only: Apply a thin coat of LIGHT CASSETTE BODY GREASE to inside of
seal lip at the outer cassette body bearing.
4. Slide the cassette body onto the axle. Make sure to rotate the cassette body counter-clockwise to disengage
the pawls and allow the cassette body to fully seat.
5. Micro Spline cassette bodies only: Apply a thin coat of WATERPROOF GREASE to the outer cassette body
bearing, then install the thin steel washer.
6. Install the correct end cap onto the axle, according to your cassette body specification:
Shimano HG and XD: Install the 17.5 mm long end cap, which has no logo.
Micro Spline: Install the 19.3 mm long end cap, which has the Micro Spline logo.

5
REAR HUB CLEANING AND LUBRICATION
This procedure should be completed once per riding season or more frequently during severe wet conditions.
TOOL LIST
Light degreaser or solvent such as Simple Green
Small flat head screwdriver or pick
Pawl and spring kit, hub seal, end cap seal kit (optional)
12 mm blind bearing puller or vise with soft jaws (optional)
Lint-free rag
Rubber gloves
HUB REMOVAL
1. Firmly pull the drive side end cap and cassette body by hand to remove them.
NOTICE: All Race Face end caps are designed to be removed by hand. Clamping end caps with vise jaws or
pliers can damage them. A rubber glove can help improve grip. A 12 mm blind bearing puller tool can be used for
dicult to remove end caps.
2. Remove the cassette body 12.55 mm spacer.
TIP: This spacer can be located on the axle against the drive side hub shell bearing OR it can stick to the inner
cassette body bearing inner race.
3. Inspect the cassette body seal lip for tears or worn edge. Use a flathead screwdriver or pick to remove and replace
the seal if it is damaged.
4. Remove the non-drive side end cap by hand.
NOTICE: All Race Face end caps are designed to be removed by hand. Clamping end caps with vise jaws or
pliers can damage them. A rubber glove can help improve grip. A 12 mm blind bearing puller tool can be used for
dicult to remove end caps.
5. Use a small flat head screwdriver or pick to remove the non-drive side end cap seal.
6. Inspect the non-drive side end cap seal lip for tears or worn edge. Use a flathead screwdriver or pick to remove
and replace the seal if it is damaged.
CLEAN AND INSPECT
1. Thoroughly inspect all parts for damage and wear. Replace the cassette body if excessive wear or corrosion are
present.
2. Thoroughly clean all parts. Clean the drive ring in the hub with degreaser and a lint-free rag. Clean the cassette
body and pawls with degreaser. Be sure to use an evaporating degreaser and wait until areas are free from
degreaser before applying fresh grease. When using degreaser be sure to keep it away from the bearings.
IMPORTANT: Do NOT apply grease or Loctite to the bearing bores.
3. Use a dry, lint-free rag to clean the non-drive side outer bearing surface and cassette body outer bearing/seal.
4. Clean all the end caps and end cap seals using a light degreaser or solvent such as Simple Green. Do not use harsh
cleaners, brake cleaner, or acetone.
REAR HUB INSTALLATION
1. Apply a small and even coat of LIGHT CASSETTE BODY GREASE to the non-drive side bearing face.
IMPORTANT: Do NOT apply grease or Loctite to the bearing bores.
2. Apply LIGHT CASSETTE BODY GREASE to the inner lip of the non-drive side end cap seal. Install the seal into
the non-drive side hub shell bore. Make sure the sealing lip edge faces out. Push the seal in until it is fully seated
against the bearing. Press the VAULT 34 or VAULT 35 by hand to fully seat the non-drive side end cap seal.
3. Install the cassette body 12.55 mm spacer onto the axle.
4. Grease the hub shell drive ring with a moderate layer of LIGHT CASSETTE BODY GREASE.
5. Apply OIL inside the cassette body seal lip.
6. Shimano HG and XD cassette bodies only: Apply a thin coat of LIGHT CASSETTE BODY GREASE to inside of seal
lip at the outer cassette body bearing.
7. Slide the cassette body onto the axle. Make sure to rotate the cassette body counter-clockwise to disengage the
pawls and allow the cassette body to fully seat.
8. Micro Spline cassette bodies only: Apply a thin coat of WATERPROOF GREASE to the outer cassette body
bearing, then install the thin steel washer.
9. Install the correct end cap onto the axle, according to your cassette body specification:
NOTE: The rear longer end cap installs on the non-drive side. The front end caps are symmetrical.
Shimano HG and XD: Install the 17.5mm long end cap, which has no logo.
Micro Spline: Install the 19.3mm long end cap, which has the Micro Spline logo.

6
END CAP REPLACEMENT
PART LIST
F60199, ENDCAP,SET,TRACE,J-BEND,FRONT,15x110 (J615)
F60196, ENDCAP,SET,TRACE,J-BEND,REAR,12x148/157 (J624/J622)
TOOL LIST
15 mm or 12 mm blind bearing puller or vise with soft jaws (optional)
Lint-free rag
Rubber gloves
REMOVAL
1. Remove the end caps by hand.
NOTICE: All Race Face end caps are designed to be removed by hand. Clamping end caps with vise jaws or pliers
can damage them. A rubber glove can help improve grip. A 15 mm or 12 mm blind bearing puller tool can be used for
dicult to remove end caps.
INSTALLATION
If the wheel is NOT new, clean the bearings with a lint-free rag and apply new grease as recommended below:
Front J615: Apply WATERPROOF GREASE to cover the outer seals of the bearing.
Rear J624/J622: Apply thin cassette body grease on the insides of the end cap seals.
For Shimano HG and XD cassette bodies only: Apply a thin coat of LIGHT CASSETTE BODY GREASE to the inside of
the seal lip at the outer cassette body bearing.
For Micro Spline cassette bodies only: Apply a thin coat of WATERPROOF GREASE to the outer cassette body
bearing, then install the thin steel washer.
2. Install the correct end cap onto the axle, according to your cassette body specification:
NOTE: The rear longer end cap installs on the non-drive side. The front end caps are symmetrical.
Shimano HG and XD: Install the 17.5mm long end cap, which has no logo.
Micro Spline: Install the 19.3mm long end cap, which has the Micro Spline logo.

7
PART NUMBER DESCRIPTION AEFFECT R
FRONT
AEFFECT R
REAR
AEFFECT R
EMTB REAR
F60190 CASSETTE BODY,TRACE.J-BEND,MTN-HG,ALLOY ●
F60191 CASSETTE BODY,TRACE.J-BEND,MTN-HG,STEEL ● ●
F60192 CASSETTE BODY,TRACE.J-BEND,XD,ALLOY ●
F60193 CASSETTE BODY,TRACE.J-BEND,XD,STEEL ● ●
F60194 CASSETTE BODY,TRACE.J-BEND,MS,ALLOY ●
F60195 CASSETTE BODY,TRACE.J-BEND,MS,STEEL ● ●
F60202 AXLE,TRACE,J-BEND,FRONT,15x110 ●
F60200 AXLE,TRACE,J-BEND,REAR,12x148 ● ●
F60201 AXLE,TRACE,J-BEND,REAR,12x157 ● ●
F60123 BEARING,18X30,CN,AM ●
8022803 BEARING 18X30 CN AM o
F60078 BEARING,6902 CM ● ●
8022798 BEARING 6902 CM AM o o
F60079 BEARING,15267 CM ● ●
8022799 BEARING 15267 CM AM o o
F60146 BEARING,6802,2PCS ● ●
F60185 BEARING,DRIFT,KIT,VAULT,F+R, AM ●●●
F60199 ENDCAP,SET,TRACE,J-BEND,FRONT,15x110 ●
F60196 ENDCAP,SET,TRACE,J-BEND,REAR,12x148/157 ● ●
F60204 SEAL,TRACE,J-BEND,CASSETTE BODY,NDS ● ●
F60203 SPACER,TRACE,J-BEND,CASSETTE BODY ● ●
F60021 MTN TUBELESS KIT,VALVE X2 /TAPE 10MX29MM ●●●
ORM20AER302928H RIM,AEFFECT-R,30,29",28H,BLK ● ●
ORM20AER3027.528H RIM,AEFFECT-R,30,27.5",28H,BLK ● ●
ORM20AEREMTB302932H RIM,AEFFECT-R,EMTB,30,29",32H,BLK ●
ORM20AEREMTB3027.532H RIM,AEFFECT-R,EMTB,30,27.5",32H,BLK ●
B60061 DECAL SHEET,MY21 AEFFECT R,29,GRY ● ●
B60062 DECAL SHEET,MY21 AEFFECT R,27.5,GRY ● ●
B60063 DECAL SHEET,MY21 AEFFECT R EMTB,29,GRY ●
B60064 DECAL SHEET,MY21 AEFFECT R EMTB,27.5,GRY ●
F60118LP185 DECAL KIT LARGE 185C RED ●●●
F60118LP389 DECAL KIT LARGE 389C NEON YELLOW ●●●
F60118LP802 DECAL KIT LARGE 802C NEON GREEN ●●●
F60118LP801 DECAL KIT LARGE 801C NEON BLUE ●●●
F60118LP021 DECAL KIT LARGE 021C ORANGE ●●●
F60118LPBLK DECAL KIT LARGE BLACK ●●●
F60118LP2597 DECAL KIT LARGE 2597C PURPLE ●●●
F60118LP10392 DECAL KIT LARGE 10392 GREY ●●●
D60125 SPOKE,J-BEND 2.0/1.7 TCS,296MM,BLK ● ●
D60124 SPOKE,J-BEND 2.0/1.7,TCS,278MM,BLK ● ●
D60127 SPOKE,J-BEND 2.0/1.8 TCS,290MM,BLK ●
D60126 SPOKE,J-BEND 2.0/1.8 TCS,271MM,BLK ●
F60128 NIPPLE,BRASS,DOUBLE SQUARE,2.0x16,SL,BLK,32PAK ●●●
D60046 TUBELESS VALVE,W/R CORE 46MM ●●●
8022218 TUBELESS VALVE w/ removable core 46mm ooo
● Compatible part.
o Alternate option. Avoid mixing dierent spoke types when possible.
APPENDIX A - TRACE SPARE PARTS LIST (J615/J624/J622)

8
APPENDIX B - TRACE HUB CODES
605-00-239 REV A
SEATPOST OWNER’S GUIDE
RACEFACE.COM
©RaceFace 2022 605-00-003 Rev A