RACING COCKPITS SPORT TRIPLE User manual

SPORT Series - TRIPLE Monitor Mount
Manual (v.05/2021.1)
If you need any assistance building, please let us know. We are here to help!
T[email protected] +1(833)RACING2
©2021 Racing Cockpits Operating Company, LLC

SPORT - TRIPLE Monitor Mount:Parts Guide
Vesa Mounts
Pivot Plates (Right Hand & Left Hand)
1-Slot Profile
4-Hole Joiner Bracket
Page 2
Sport Series - TRIPLE Monitor Mount Manual (v.05/2021.1)

SPORT - TRIPLE Monitor Mount:Parts Guide
(Cont.)
2-Hole 90° Corner Bracket
1-Hole End Cap
Standard Spring T-Nut
16mm Standard Bolt 12mm SHORT Bolt
Page 3
Sport Series - TRIPLE Monitor Mount Manual (v.05/2021.1)

How to Use T-Nuts: A Quick Guide
Method 1: Simply slide T-Nut into T-Slot from the side.
Method 2: Push T-Nut into T-Slot at an angle then snap into place so it ends up flat. You can
lever the allen wrench in the screw hole to help with this. This method is what you will use
once the ends are blocked.
Page 4
Sport Series - TRIPLE Monitor Mount Manual (v.05/2021.1)

How to Use T-Nuts: A Quick Guide (Cont.)
Once T-Nut is in place, simply secure bracket etc. with the correct length bolt.
PRO TIP: If you are installing vertically and need to hold the T-Nut in place, you can put
the long end of the allen wrench into the T-Slot channel to hold it from below while hand
tightening the bolt to secure it from sliding. Then do final tightening with the allen
wrench.
Page 5
Sport Series - TRIPLE Monitor Mount Manual (v.05/2021.1)

Build Guide
Step 1: Connect Monitor Mount Uprights
Profile:
● 2 x 19” 1-Slot Profiles
Hardware:
● 2 x 4-Hole Joiner Brackets
● 8 x 16mm Standard Bolts
● 8 x Standard Spring T-Nuts
Connect 19” monitor uprights to the back of cockpit uprights. TIGHTEN well. These will
hold a lot of weight.
Page 6
Sport Series - TRIPLE Monitor Mount Manual (v.05/2021.1)

Step 2: Add Lower Extender Arm Brackets
● 2 x 2-Hole 90° Corner Brackets
● 2 x 16mm Standard Bolts
● 2 x Standard Spring T-Nuts
Both need to be level with each other. Use a tape measure to ensure they are at the same
height. You will fine tune the height for your monitors in a later step.
Page 7
Sport Series - TRIPLE Monitor Mount Manual (v.05/2021.1)

Step 3: Add Extender Arms
Profile:
● 2 x 10” 1-Slot Profiles
Hardware:
● 2 x 16mm Standard Bolts
● 2 x Standard Spring T-Nuts
Both need to be even front to back with each other. Use a tape measure to ensure they
are mounted at the same distance. You will fine tune the distance to your monitors in a
later step.
Page 8
Sport Series - TRIPLE Monitor Mount Manual (v.05/2021.1)

Step 4: Add Upper Extender Arm Brackets
● 2 x 2-Hole 90° Corner Brackets
● 4 x 16mm Standard Bolts
● 4 x Standard Spring T-Nuts
Page 9
Sport Series - TRIPLE Monitor Mount Manual (v.05/2021.1)

Step 5: Add Horizontal Rail
Profile:
● 1 x 40.5” 1-Slot Profile
Hardware:
● 2 x 2-Hole 90° Corner Brackets
● 4 x 16mm Standard Bolts
● 4 x Standard Spring T-Nuts
Horizontal rail needs to be resting ON TOP of extender arms, flush with the ends of the
extender arms.
Horizontal rail needs to be centered. Use a tape measure to ensure the connections to
the extender rails on each are the same distance side to side.
Page 10
Sport Series - TRIPLE Monitor Mount Manual (v.05/2021.1)