Radiant Slim RBA CS 100 E User manual

CE 0694 RBA CS 100 - RAD - ING - MAN.UT - 0807B - DIGITECH
Documentazione Tecnica RADIANT BRUCIATORI S.p.A. Montelabbate (PU) ITALY ITALIANO
User Manual
for model
RBA CS 100 E
Floor standing
storage combi cylinder
room sealed chamber

USER INSTRUCTIONS
1
BOILER OPERATING INSTRUCTIONS
Make sure that the authorised technician who tested the boiler has stamped the guarantee booklet.
The installation, first start-up, regulation and maintenance operations must be carried out exclusively by qualified
personnel (e.g. Radiant authorised Service Centres). Incorrect installation can cause damage to property and
injury to persons or animals, for which the manufacturer will not be held responsible.
During the installation, the technician must carry out the following checks:
■The data on the data plate must correspond to that of the mains supply networks (gas, electricity, water);
■The boiler must be regulated according to its designed use and performance;
■The flue gas exhaust and combustion air intake system must be correctly installed and operational;
■The exhaust gas discharge and ventilation systems must comply with the requirements of national and local
standards regardless of whether the boiler is installed indoors, outdoors or in its own cabinet (see section
“Reference standards”.
General warnings
If there is any doubt as to whether the appliance has been tested by an authorised technician, do not attempt
to start it. All maintenance and gas conversion operations must be carried out by professionally qualified
personnel, registered in accordance with current legislation and according to UNI-CIG 7129/01 and
subsequent updates.
Make sure that the requirements relating to the air intake and ventilation of the room in which the
boiler is to be installed have been complied with.
The boilers can be installed outdoors in a partially protected location, in accordance with current
standards and where the minimum external temperature does not fall below –10°C. The manufacturer
will not be held responsible for installation in locations where the temperature falls to below –10°C.
The boiler is fitted with an antifreeze system. If the boiler is installed in a location where there is a risk of
freezing, the anti-freeze system will only come into operation if the appliance is switched on (i.e. with the
boiler switch in the ON position) and the gas supply valve is open. The manufacturer will not be held
responsible for damage to the boiler caused by non-compliance with this instruction.
Should any part of the boiler freeze-up, do not attempt to light it under any circumstances, but instead call the
Service Centre immediately.
The appliance’s combustion system must be checked every two years. This check includes testing the
efficiency of the boiler and must be carried out by authorised personnel possessing the qualifications as
required by current law.
Do not obstruct the ventilation openings in rooms where there are gas-burning appliances installed (boiler,
cooker, etc.).

USER INSTRUCTIONS
2
If you smell gas …
DO NOT ACTIVATE ANY ELECTRIC SWITCHES, TELEPHONES OR ANY OTHER DEVICE THAT MAY
GENERATE ELECTRICAL DISCHARGES OR SPARKS.
OPEN DOORS AND WINDOWS IMMEDIATELY TO CREATE A CURRENT OF AIR THAT WILL RAPIDLY
CLEAR THE ROOM.
CLOSE ALL GAS TAPS AND VALVES.
CALL FOR PROFESSIONALLY QUALIFIED PERSONNEL.
Boiler controls - Control panel
LEGEND
1. ON/OFF SWITCH
2. HEATING TEMPERATURE CONTROL KNOB
3. D.H.W TEMPERATURE CONTROL KNOB.
4. D.H.W TEMPERATURE DISPLAY BUTTON. (KEEP PRESSED FOR 5 SECONDS TO DISPLAY OUTSIDE
TEMPERATURE -ONLY WITH OPTIONAL OUTDOOR SENSOR)
5. SERVICE BUTTON.
6. SUMMER, WINTER OR SUMMER/WINTER MODE SELECTION BUTTON.
7. TERMINAL BOARD FOR EXTERNAL WIRING.
8. TEMPERATURE, ERROR CODE AND OPERATING STATUS DISPLAY.
Fig. 1 6754321
8

USER INSTRUCTIONS
3
Starting - up the boiler
Open the gas Isolation valve located under
the boiler.
Switch on the boiler by placing the ON/OFF
switch (1)in the ON position (see “Control
panel”).
The boiler will light automatically (with the
WINTER mode selected and room
thermostat connected).
Check that there are no flashing numbers
on the display 8(see error codes). If code
H2O appears on the display 8this denotes
that there is no water in the boiler.
Consequently, fill the system as described
in section “Filling the system”.
■“SUMMER” mode
To switch boiler operation to “SUMMER” mode, press button 6(see fig. 1). The boiler will only work for the D.H.W
system. The “SUMMER” mode setting of the boiler is signalled by the symbol lit continuously on the control
panel.
The automatic ignition system will light the burner every time there is a demand for domestic hot water. In this
case, the symbol on the control panel will flash.
■“WINTER” mode
To switch boiler operation to “WINTER” mode, press button 6(see fig. 1). The boiler will only work for the central
heating system. The “WINTER” mode setting of the boiler is signalled by the symbol lit continuously on the
control panel.
The automatic ignition system will light the burner every time there is a demand for room heating. In this case, the
symbol on the control panel will flash.
■“SUMMER-WINTER” mode
To switch boiler operation to “SUMMER/WINTER” mode, press button 6(see fig. 1). The boiler will work for both
central heating/D.H.W systems. The “SUMMER/WINTER” mode setting of the boiler is signalled by the symbols
lit continuously on the control panel.
The automatic ignition system will light the burner every time there is a demand for room heating or domestic hot
water, the functioning is signalled by the symbols flashing continuously on the control panel.
■Regulating the heating temperature
The heating temperature is regulated by knob 2 (see fig.1).
Rotating the knob anticlockwise reduces the temperature.
Rotating the knob clockwise increases the temperature.
The range of temperature settings for the central heating runs from a minimum of 30°C to a maximum of 80°C,
or, in the case of low temperature operation, from a minimum of 25°C to a maximum of 59°C.
6754321
8
Fig. 1

USER INSTRUCTIONS
4
■D.H.W. temperature control
The domestic hot water temperature is regulated by knob
3 (see “Control panel”).
Rotating the knob anticlockwise reduces the
temperature.
Rotating the knob clockwise increases the
temperature.
The range of temperature settings for the domestic
hot water runs from a minimum of 35°C to a maximum
of 60°C.
■Topping-up the system with water
The water pressure in the central heating circuit must be checked during the entire period of operation of the boiler.
In this respect, the reading on the pressure gauge M(fig. 2), located on the lower part of the boiler, must not be
less than 1 bar.
If there is insufficient water in the boiler, the code H2O will flash on the display (see fig 2).
To bring the system back up to pressure, open the external filling tap R (fig. 2) and use the pressure gauge M(fig.
2) to check that the system pressure reaches 1 bar and that the code H2O lights up.
Diagnostics – Error codes:
This paragraph contains a list of error codes that the boiler may generate on the display 8 (see “Control panel”)
together with the relative indications and the operations that the user can carry out to reset the boiler.
If the problem re-occurs after the following actions have been taken, call an authorised Service
Centre.
_E01_ Ionisation block
Code E01 lit continuously on the display.
Check that the gas valve on the boiler and gas meter are open and that there is gas in the mains supply (or in
the tank).
Switch off then switch on the appliance using switch 1(see “Control panel”) on the control panel.
When the error code on the display disappears, the boiler will restart.
If the problem persists, Call the Service Centre.
_E02_ Safety Thermostat tripped
Code E02 lit continuously on the display. Call the Service Centre.
_h2o_Water Pressure Switch tripped
Code H2O lit continuously on the display.
Check the water pressure in the central heating circuit. The reading on the pressure gauge M(see fig. 2),
located on the lower part of the boiler, must not be less than 1 bar .
If the pressure is less than 1 bar, top-up the system as described in paragraph “Filling the system”.
The boiler will restart automatically.
If the problem persists, Call the Service Centre.
_E05_ Heating Sensor malfunction
Code E05 lit continuously on the display. Call the Service Centre.
Fig. 2
M
R

USER INSTRUCTIONS
5
_E12_ D.H.W boiler sensor malfunction
Code E12 lit continuously on the display. Call the Service Centre.
_E14_ Air Pressure Switch Tripped
Code E14 lit continuously on the display. Call the Service Centre.
_E22_Parameter programming request
Code E22 lit continuously on the display. Call the Service Centre.
_E35_Flame Detection Malfunction
Code E35 lit continuously on the display. Call the Service Centre.
N.B. If the boiler is to be left unused for a long period of time, the user must do one of the following:
Make the boiler safe by disconnecting all the power supplies (electricity and gas), and draining the heating
system and the condensate trap.
Leave the boiler in standby, leaving the electricity and gas supplies connected and, consequently the anti-freeze
function.

RADIANT BRUCIATORI s.p.a.
Via Pantanelli, 164/166 - 61025 Loc. Montelabbate (PU)
Tel. [phone] • fax. [phone]
e-mail: tecnico@radiant • Internet: http://www.radiant.it
THE TECHNICAL DATA AND MEASUREMENTS ARE PROVIDED FOR INFORMATION
PURPOSES ONLY AND ARE NOT BINDING. THE COMPANY RESERVES THE RIGHT
TO APPLY VARIATIONS WITHOUT PRIOR NOTIFICATION. NEITHER WILL THE
COMPANY BE HELD RESPONSIBLE FOR ANY INACCURACIES IN THIS HANDBOOK
DERIVING FROM PRINTING OR TRANSLATION ERRORS. E+OEALL RIGHTS
RESERVED. NO PART OF THIS DOCUMENT MAY BE REPRODUCED, MEMORISED
IN ANY FILING SYSTEMS OR TRANSMITTED IN ANY FORM WHATSOEVER,
INCLUDING ELECTRONIC, MECHANICAL, PHOTOCOPIES, RECORDINGS OR ANY
OTHER MEANS WITHOUT THE COMPANY’S PRIOR WRITTEN APPROVAL.