Radio Shack 15-1981 User manual

Cat. No. 15-1981
OWNER’S MANUAL
Please read before using this equipment.
181-CHANNEL REMOTE CONTROL
CABLE CONVERTER
with Volume Control
15-1981.fm Page 1 Tuesday, March 30, 1999 9:09 AM

2
INTRODUCTION
Your RadioShack 181-Channel Re-
mote Control Cable Converter lets you
connect a non-cable-ready video
product to cable. It is compatible with
all cable systems and gives you com-
plete remote control selection of all
cable channels (VHF, Mid-Band, Su-
per-Band, and Hyper-Band). The con-
verter’s volume control lets you adjust
a connected TV’s sound. You can also
use the converter’s remote control to
turn on or off and fine tune most TVs.
Important Note: This cable converter
does not decode “scrambled” premi-
um channels. You can, however, use
it with the cable box provided by the
cable company so you can receive
premium channels and still have re-
mote control of all other channels.
Note to Cable TV System Installer:
This reminder is provided to call the
CATV system installer’s attention to
Article 820-40 of the NEC that pro-
vides guidelines for proper grounding
and, in particular, specifies that the
cable ground be connected to the
grounding system of the building as
close to cable entry as practical.
Note: You need two AAA batteries
and a 75-ohm coaxial cable to operate
your converter. You might also need
extra coaxial cable, an A/B switch, a
two-way splitter, and (if your TV has
only 300-ohm terminals) a 75-to-300
ohm transformer. Read the entire
“Connecting the Converter” section of
this Owner’s Manual before you begin
to install your converter.
We recommend you record your con-
verter’s serial number here. The num-
ber is on the bottom of the converter.
Serial Number __________________
WARNING:To reduce the risk of fire or
shock hazard, do not expose this product to
rain or moisture.
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that
might be of sufficient magnitude
to constitute a risk of electric
shock. Do not open the prod-
uct’s case.
This symbol is intended to
inform you that important oper-
ating and maintenance instruc-
tions are included in the
literature accompanying this
product.
The graphical symbols with supplemental
markings are located on the back of the prod-
uct.
!
!
© 1999 Tandy Corporation.
All Rights Reserved.
RadioShack is a registered trademark used by Tandy Corporation.
15-1981.fm Page 2 Tuesday, March 30, 1999 9:09 AM

3
CONTENTS
Preparation ........................................................................................................... 4
Setting CH4/CH3 ............................................................................................ 4
Choosing the Cable System Type ................................................................... 4
Connecting the Converter to AC Power .......................................................... 5
Turning the Converter On/Off .......................................................................... 5
Using the Switched AC Outlet ......................................................................... 6
Connecting the Converter .................................................................................. 7
Connecting to a TV ......................................................................................... 7
Connecting to Cable ........................................................................................ 7
Single-Wire Cable System ........................................................................ 8
Two-Wire Cable System ........................................................................... 9
Connecting to a VCR .................................................................................... 10
Recording and Viewing a Non-Premium Cable Channel ........................ 10
Recording and Viewing a Premium Cable Channel ................................ 11
Operation ............................................................................................................ 12
Operating the Converter’s Receiver .............................................................. 12
Using the Remote Control ............................................................................. 13
Remote Control TVs ............................................................................... 14
Adjusting the Volume .................................................................................... 14
Muting the Sound .......................................................................................... 14
Storing a Channel in Memory ....................................................................... 14
Setting the Sleep Timer ................................................................................ 15
Using Parental Lock (PL) .............................................................................. 15
Locking a Channel .................................................................................. 15
Watching a Locked Channel ................................................................... 15
Unlocking a Channel .............................................................................. 16
Changing the Security Code ......................................................................... 16
Resetting the Security Code ......................................................................... 16
Variations in Channel Numbering ................................................................. 17
Care and Maintenance ...................................................................................... 19
The FCC Wants You to Know ........................................................................ 20
Specifications .................................................................................................... 21
15-1981.fm Page 3 Tuesday, March 30, 1999 9:09 AM

4
PREPARATION
Your converter’s remote control re-
quires two AAA batteries (not sup-
plied) for power. For the best
performance and longest life, we rec-
ommend RadioShack alkaline batter-
ies.
Cautions:
• Use only fresh batteries of the
required size and recommended
type.
• Do not mix old and new batteries,
different types of batteries (stan-
dard, alkaline, or rechargeable), or
rechargeable batteries of different
capacities.
Follow these steps to install batteries.
1. Slide the battery compartment
cover in the direction of the arrow
to remove it.
2. Place the batteries in the com-
partment as indicated by the
polarity symbols (+ and –) marked
inside.
3. Replace the cover.
When the remote control stops operat-
ing properly, replace the batteries.
Warning: Dispose of old batteries
promptly and properly. Do not burn or
bury them.
Caution: If you do not plan to use the
remote control for a month or more,
remove the batteries. Batteries can
leak chemicals that can destroy elec-
tronic parts.
SETTING CH4/CH3
Set your TV’s tuner to Channel 3 or 4
(whichever is not used for broadcasts
in your area). Then set CH4/CH3 on
the back of the converter to match the
channel you selected on your TV’s
tuner.
CHOOSING THE CABLE
SYSTEM TYPE
There are three types of cable TV
channel frequency systems: stan-
dard, IRC, and HRC. Most cable sys-
tems use a standard system. Your
converter is preset to use a standard
channel frequency system.
15-1981.fm Page 4 Tuesday, March 30, 1999 9:09 AM

5
Caution: To avoid damaging your
converter, make sure your converter is
not connected to an AC outlet before
setting IRC/HRC/STD.
Note: If you are not sure what type of
channel frequency system your cable
system uses, contact your local cable
company.
If the cable system in your area is not
standard, use a paper clip or other
pointed object to set IRC/HRC/STD on
the bottom of the converter for the
type of cable system you have.
Note: HRC and IRC are methods
used by some cable companies for
converting satellite and local broad-
cast channels to cable channels.
Channels 5 and 6 on IRC systems and
all channels on HRC systems are
slightly different frequencies from
those used on standard systems.
CONNECTING THE
CONVERTER TO AC
POWER
Plug the converter’s power cord into a
standard AC outlet.
TURNING THE
CONVERTER ON/OFF
To turn the converter on or off, press
POWER on the front of the converter or
on the remote control.
15-1981.fm Page 5 Tuesday, March 30, 1999 9:09 AM

6
USING THE SWITCHED
AC OUTLET
The converter’s built-in switched AC
outlet lets you connect a TV or anoth-
er electronic device that uses 120V,
60Hz power (up to 600 watts) directly
to the converter.
Press POWER on the converter or re-
mote control to turn on the converter
and the outlet. Press POWER again to
turn them off.
Notes:
• If a TV you plugged into the
switched AC outlet has an instant-
on feature, it might go into a
standby mode when you turn on
the converter. If this happens, you
might have to turn on your TV
using its power switch or remote
control.
• If you plugged a digital TV into the
switched AC outlet, it might auto-
matically reset to a channel other
than 3 or 4 when you turn off the
converter. If this happens, you
might want to plug it into a stan-
dard AC outlet and turn it on and
off manually.
15-1981.fm Page 6 Tuesday, March 30, 1999 9:09 AM

7
CONNECTING THE CONVERTER
CONNECTING TO A TV
Use the supplied 75-ohm coaxial ca-
ble with F-type connectors to connect
the 75-ohm terminal on your TV to the
RF OUT terminal on the back of the
converter. If your TV has only 300-
ohm terminals, use a 75-to-300 ohm
transformer (not supplied), available
from your local RadioShack store.
CONNECTING TO CABLE
How you connect your converter de-
pends on the complexity of your video
system. Refer to the connection ex-
amples on the next few pages to find
the one that is most similar to your
system.
Notes:
• Your system might use a combina-
tion of two or more of the following
examples. If you have questions,
take a diagram of your system to
your local RadioShack store for
assistance.
• Check local regulations before
connecting any device to your
cable system.
Connect the cable company’s coaxial
cable to the RF IN terminal on the back
of the converter.
15-1981.fm Page 7 Tuesday, March 30, 1999 9:09 AM

8
Single-Wire Cable System
Connect to TV R/F Inputs
Connect to TV Audio/Video Inputs
TV Set
Matching Transformer
(75-300 Ohm)
Cable Converter
Switched
AC Outlet
CH4/CH3
From Cable Company
AC Plug from TV Set To Standard
AC Outlet
Cable Converter Switched
AC Outlet
From Cable
Company
TV Set
To Standard
TV Set
AC Outlet
15-1981.fm Page 8 Tuesday, March 30, 1999 9:09 AM

9
Two-Wire Cable System
Some cable systems offer more than 181 channels and include two incoming wires.
To use your converter with such a system, install an A/B switch (not supplied),
available from your local RadioShack store, to connect the cable company’s wires
to the converter.
Use the A/B switch to select the group of channels you want to watch.
A/B Switch
Two Wires From
Cable Company
Cable Converter Switched
AC Outlet
To Standard
AC Outlet
CH4/CH3
From
AC Plug From TV Set
Cable
Company TV Set
Matching Transformer
(75-300 Ohm)
15-1981.fm Page 9 Tuesday, March 30, 1999 9:09 AM

10
CONNECTING TO A VCR
Recording and Viewing a Non-Premium Cable Channel
This connection lets you record a non-premium cable channel while you view it.
Switched
AC Outlet
To Standard
AC Outlet (both)
To Standard
AC Outlet
Cable Converter
TV Set
VCR From Cable Company
CH4/CH3
Matching Transformer
(75-300 Ohm)
15-1981.fm Page 10 Tuesday, March 30, 1999 9:09 AM

11
Recording and Viewing a Premium Cable Channel
This connection lets you:
• record a premium or non-premium cable channel while you view it
• record a premium cable channel while you view a non-premium cable channel
• record a non-premium cable channel while you view another non-premium
cable channel
Use an A/B switch (not supplied) to connect your TV set to the VCR and the cable
converter. Use a two-way splitter (not supplied) to connect the cable company’s
wire to the converter and the cable company’s CATV box. Your local RadioShack
store has the accessories you need to make this connection.
With the A/B switch set to the converter position, you have remote control of all ca-
ble channels, except premium cable channels.
When you want to view premium channels, set the A/B switch to the position for
CATV. Then follow the instructions in the VCR’s owner’s manual to set the channel
switches on the VCR and CATV box.
Switched
AC Outlet
To Switched
AC Outlet
To Standard
AC Outlet
Cable Converter
TV Set
VCR
From Cable
Company
To Standard
AC Outlet
Two-Way Splitter
CATV Box
Matching Transformer
(75-300 Ohm)
15-1981.fm Page 11 Tuesday, March 30, 1999 9:09 AM

12
OPERATION
OPERATING THE
CONVERTER’S
RECEIVER
Press POWER on the converter or re-
mote control to turn the converter and
the switched AC outlet on and off.
When you turn off the converter, a dot
appears on the lower right corner of
the display to indicate that the con-
verter is in standby mode.
Press CHANNEL or on the con-
verter to select individual channels, or
hold down CHANNEL or to scan
channels in the direction of the arrow.
The selected channel appears on the
display.
Press VOLUME on the converter or
VOL on the remote control to in-
crease the volume, or press VOLUME
on the converter or VOL on the
remote control to decrease it.
Press CATV/TV to select either the
CATV or TV mode. In TV mode, U
(TV) appears before the channel num-
ber on the display.
Sample Display Indications
•125 — CATV Channel 125.
•U16 — TV Channel 16.
•U52. — TV Channel 52 is a
favorite channel.
•11.5 — CATV Channel 115 is
receiving a program and the sleep
timer has been set up.
•1.2.5. — CATV Channel 125 is
locked and it is also a favorite
channel. The sleep timer has
been set up.
•⊆⊆ — Press MEM or FAV to start a
memory operation.
•∪•∪ — Press PL to activate
parental lock.
•∪.1— the 1st digit of a parental
control code.
•∪.2— the 2nd digit of a parental
control code.
•∪.3— the 3rd digit of a parental
control code.
•⊂⊂ — Press FINE TUNE to con-
firm your entry, or store a pro-
grammed function in memory.
•⊃⊃ — Press FINE TUNE to con-
firm your entry, or erase a pro-
grammed function from memory.
Standby/Favorite Channel
Sleep Timer
Parental Lock
15-1981.fm Page 12 Tuesday, March 30, 1999 9:09 AM

13
USING THE REMOTE
CONTROL
The remote control lets you operate
your converter from across the room.
For the most dependable operation,
point the remote control toward the
converter’s display.
Here is a description of each of the re-
mote control’s keys:
MUTE — press to temporarily turn off
sound. To restore sound, press MUTE
again.
SLEEP — lets you set your converter
to automatically turn off after the pre-
set time.
FINE TUNE / — press to receive
the best possible reception or confirm
the entry of MEM, FAV, and PL.
PL (Parental Lock) — use with FINE
TUNE to lock channels.
MEM — use with FINE TUNE to
store a channel you previously fine-
tuned.
MR (Memory Recall) — press to tune
to your favorite channel stored in
memory.
Number Buttons (0–9) — press to di-
rectly select channels. Precede sin-
gle-digit channels with a 0(02, 03, 04,
and so on).
RESET (Fine Tuning Center) — press
to return to the default setting.
POWER — press to turn the converter
and the switched AC outlet on and off.
CATV/TV — press to select CATV or
TV mode.
VOL / — press to increase vol-
ume or to decrease it.
FAV — use with FINE TUNE to store
a favorite channel or with FINE TUNE
to delete it.
LAST (Last Channel Recall) — press
to recall the channel you selected be-
fore the current channel.
CH / — press to select individual
channels or scan channels in the di-
rection of the arrow. The converter’s
display shows the channel number.
15-1981.fm Page 13 Tuesday, March 30, 1999 9:09 AM

14
Remote Control TVs
If your TV has a remote control and
your converter’s remote control inter-
feres with the TV’s operation, either
turn off the TV’s remote control fea-
ture (if the TV has a remote control on/
off switch) or cover the TV’s remote
control receiver window (with a piece
of black tape, for example).
ADJUSTING THE
VOLUME
Repeatedly press VOLUME or
on the converter or VOL or on
the remote control to adjust the vol-
ume.
MUTING THE SOUND
Press MUTE on the remote control to
temporarily turn off the sound. To re-
store the sound, press MUTE again or
repeatedly press VOLUME or on
the converter or VOL or on the
remote control.
STORING A CHANNEL
IN MEMORY
Follow these steps to store a favorite
channel in memory.
1. Repeatedly press CHANNEL or
on the converter or CH or
on the remote control to select
the channel.
2. Press FAV.
3. Press FINE TUNE . A dot
appears on the lower right corner
of the display.
To select the channel currently stored
in memory, press MR.
To remove a stored channel from
memory, repeatedly press CHANNEL
or on the converter or CH or
on the remote control to select it,
press FAV, then press FINE TUNE .
The channel is deleted from memory
and the dot disappears from the dis-
play.
MUTE
15-1981.fm Page 14 Tuesday, March 30, 1999 9:09 AM

15
SETTING THE SLEEP
TIMER
Follow these steps to set the convert-
er to automatically turn off after a cer-
tain length of time (90, 60, or 30
minutes).
1. Press SLEEP
. 9.0 appears and
the sleep timer indicator lights.
2. Repeatedly press SLEEP until the
desired length of time appears.
When the preset time is reached, 00
appears and the converter automati-
cally turns off.
Notes:
• To see the remaining time on the
timer, press SLEEP once.
• To turn off the timer, repeatedly
press SLEEP until 00 appears.
The sleep timer indicator disap-
pears and the converter stays on
until you turn it off.
USING PARENTAL LOCK
(PL)
To prevent children from viewing adult
programs (for example), you can lock
channels you select then set the con-
verter so it does not tune them.
Note: Your converter’s security code
is preset to 2999, but you can change
it (see “Changing the Security Code”
on Page 16).
Locking a Channel
1. Repeatedly press CH or on
the remote control to select the
channel you want to lock.
2. Press PL. ∪∪ appears.
3. Hold down FINE TUNE to lock
the selected channel. ⊂.⊂
appears to confirm the entry.
4. Release FINE TUNE . ∪.∪
appears to indicate the channel is
locked.
Watching a Locked Channel
1. Repeatedly press CH or on
the remote control to select the
locked channel you want to watch.
2. Press PL then use the number
keys on the remote control to
enter the security code (preset to
2999). ∪.1, ∪.2, and ∪.3
appear for about two seconds,
then the converter unlocks all
channels.
To re-lock all channels, turn the con-
verter off then turn it back on again.
15-1981.fm Page 15 Tuesday, March 30, 1999 9:09 AM

16
Unlocking a Channel
1. Repeatedly press CH or on
the remote control to select the
desired locked channel.
2. Press PL, then use the number
keys on the remote control to
enter the security code. The con-
verter unlocks the channel.
3. Press PL. ∪∪ appears. Then hold
down FINE TUNE to unlock the
selected channel. ⊃⊃ appears to
confirm the entry. The converter
deletes the lock.
CHANGING THE
SECURITY CODE
1. Repeatedly press CH or on
the remote control to select a
locked channel.
2. Press PL then use the number
keys on the remote control to
enter the current 4-digit security
code (preset to 2999).
3. Press PL then use the number
keys on the remote control to
enter a new 4-digit security code.
4. Press FINE TUNE .
RESETTING THE
SECURITY CODE
1. Follow Steps 1 and 2 under
“Unlocking a Channel.”
2. Press PL, then use the number
keys on the remote control to
enter 71269 (your converter’s
default master code) within 3 sec-
onds. The converter resets the
security code to 2999.
15-1981.fm Page 16 Tuesday, March 30, 1999 9:09 AM

17
VARIATIONS IN
CHANNEL NUMBERING
Some cable companies use a channel
numbering system that is different
from the one used by your converter.
For example, the channel your cable
company calls 21 might appear as 18
on the converter’s display.
Use the supplied channel number la-
bels to mark the cable company’s
channel numbers that differ from the
channels on the converter’s display.
Then peel off the backing on each la-
bel and paste the large label on the
converter and the small label on your
remote control.
This table compares channels that
your converter shows to channel num-
bers that might be assigned by your
local cable company.
Indicator Cable Channel
1 1
22
33
44
55
66
77
88
99
10 10
11 11
12 12
13 13
14 A
15 B
16 C
17 D
18 E
19 F
20 G
21 H
22 I
23 J
24 K
25 L
26 M
27 N
28 O
29 P
30 Q
31 R
32 S
33 T
34 U
35 V
36 W
37 AA or W+1
38 BB or W+2
39 CC or W+3
40 DD or W+4
Indicator Cable Channel
15-1981.fm Page 17 Tuesday, March 30, 1999 9:09 AM

18
41 EE or W+5
42 FF or W+6
43 GG or W+7
44 HH or W+8
45 II or W+9
46 JJ or W+10
47 KK or W+11
48 LL or W+12
49 MM or W+13
50 NN or W+14
51 OO or W+15
52 PP or W+16
53 QQ or W+17
54 A6 or W+18
55 A7 or W+19
56 A8 or W+20
57 A5 or W+21
58 A4 or W+22
59 A3 or W+23
60 A2 or W+24
61 A1 or W+25
62 RR or W+26
63 SS or W+27
64 TT or W+28
65 UU or W+29
66 VV or W+30
67 WW or W+31
68 XX or W+32
69 YY or W+33
Indicator Cable Channel
70 ZZ or W+34
71 AAA or W+35
72 BBB or W+36
73 CCC or W+37
74 DDD or W+38
75 EEE or W+39
76 FFF or W+40
77 GGG or W+41
78 HHH or W+42
79 III or W+43
80 JJJ or W+44
81 KKK or W+45
82 LLL or W+46
83 MMM or W+47
84 NNN or W+48
85 OOO or W+49
86 PPP or W+50
87 QQQ or W+51
88 RRR or W+52
89 SSS or W+53
90 TTT or W+54
91 UUU or W+55
92 VVV or W+56
93 WWW or W+57
94 XXX or W+58
95 A-5
96 A-4
97 A-3
98 A-2
Indicator Cable Channel
99 A-1
100 YYY or W+59
101 ZZZ or W+60
102 W+61
103 W+62
104 W+63
105 W+64
106 W+65
107 W+66
108 W+67
109 W+68
110 W+69
111 W+70
112 W+71
113 W+72
114 W+73
115 w+74
116 w+75
117 w+76
118 w+77
119 w+78
120 w+79
121 w+80
122 w+81
123 w+82
124 w+83
125 w+84
Indicator Cable Channel
15-1981.fm Page 18 Tuesday, March 30, 1999 9:09 AM

19
CARE AND MAINTENANCE
Your RadioShack 181-Channel Remote Control Cable Converter is an example
of superior design and craftsmanship. The following suggestions will help you
care for your converter so you can enjoy it for years.
Keep the converter dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the converter only in normal temperature environ-
ments. Temperature extremes can shorten the life of electronic devic-
es, damage batteries, and distort or melt plastic parts.
Keep the converter away from dust and dirt, which can cause prema-
ture wear of parts.
Handle the converter gently and carefully. Dropping it can damage
circuit boards and cases and can cause the converter to work improp-
erly.
Use only fresh batteries of the required size and recommended type.
Batteries can leak chemicals that damage your converter’s electronic
parts.
Wipe the converter with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the converter.
Modifying or tampering with the converter’s internal components can cause a
malfunction and might invalidate its warranty and void your FCC authorization to
operate it. If your converter is not performing as it should, take it to your local Ra-
dioShack store for assistance.
15-1981.fm Page 19 Tuesday, March 30, 1999 9:09 AM

20
THE FCC WANTS YOU TO KNOW
Your converter might cause TV or radio interference even when it is operating
properly. To determine whether your converter is causing the interference, turn off
your converter. If the interference goes away, your converter is causing it. Try to
eliminate the interference by:
• moving your converter away from the receiver
• connecting your converter to an outlet that is on a different electrical circuit from
the receiver
• contacting your local RadioShack store for help
If you cannot eliminate the interference, the FCC requires that you stop using your
converter.
15-1981.fm Page 20 Tuesday, March 30, 1999 9:09 AM