RAM PRODUCTS BP50 User manual

OWNER’S MANUAL
Please take a moment to read this manual prior to operation!
BRUSHLESS SYSTEM
3-2018 issue 1
182 Ridge Road, Suite D, Dayton, N.J 08810
Phone: [phone] Fax: [phone]
[e-mail] www.ramhp.com

1
CONTROLLER Set-Up
1. The controller has automatic detection for heat or temperature utilizes thermal sensors it will shut
down the unit preventing operation and possible damages. The display window will flash as an alert.
Turn off the main power switch (#5) and check for possible causes.
2. ALWAYS make sure that the proper input voltage is correct according to the label specifications.
3. In the event the unit does not operate, check all connections for the power cord at (#1) and the
wall outlet, handpiece connection at (#11), and the foot pedal connection at (#3).
In the unlikely event of overheating, the unit will resume its operation after cooling.
•Turn off the main power switch when not in use to avoid power and electric current to the controller.
•Always check the handpiece carefully for smooth operation prior to each use.
•Do not use with any other brands of equipment as brushless units are not compatible with other brands.
Items to Check If Operation Has Failed
Safety Tips!
Standard
Place in a convenient location avoiding any moisture or chemicals.
All components should be connected prior to turning on the main power switch (#5).
Make sure the power cord is securely attached in the rear (#1).
BP50 controller utilizes a state of the art microprocessor chip for programming of speed control,
overload and safety and much more. This includes a memory feature to remember the last user
settings before the main power is turned off.
Power Outlet: Main power cord receptacle. This also contains a safety fuse drawer and if there is
no power, you can use the fuse. This is the main power switch to prepare the unit.
1
Power Fuse: Shows the fuse location and is conveniently located to access if needed
(5x20mm – 2amp fuse).
2
Speed Pedal Interface: Variable speed foot control connects here.
3
Operation Indicator: LED speed display and error alerts.
4
Main Power Switch: Turns the unit on and off.
5
Knob Speed Indicator: Indicates operation in the hand mode has been selected, therefore the
speed is controlled by the speed dial (#10).
6
Motor: When the main power switch is on, the controller waits attention and is ready for use in
standby mode. Touch the motor button to start the operation.
7
Reverse Light: Indicates operation in reverse direction has been selected.
8
Forward Light: Indicates operation in forward direction has been selected.
9
Speed Control Knob: Used to adjust or vary the desired speed. In hand mode, the speed totally
controls the handpiece speed. While using in foot pedal mode, the speed dial setting can also
limit the top or maximum speed for greater control and safety.
10
Handpiece Socket: Connects the handpiece on the plug.
11
Foot Speed Indicator: Indicates operation by the foot pedal has been selected.
12
Motor Button: Engages the handpiece for operation and use or can disengage for stopping or
taking a rest from operation while remaining ready.
13
Control Mode Button: To operate by the speed dial and hand control or with the foot pedal and
speed dial as set.
14
Forward/Reverse Button: Controls handpiece direction to forward or reverse.
15
Model Input Output MaxAmp Rotate Speed Power L W H Wt.
BP50
AC110V
50HZ-60HZ
AC220V -50HZ DC0-36V 0.35A 1000-50,000 50W 170mm 160mm 80mm 1.561kg
2

4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Front Sheath
Chuck
O Ring
Dust Shield A
Dust Shield B
O Ring
Flat Washer
1260zz Bearing
Spindle Bushing
1480zz Bearing
Chuck Case
Aluminum Spring Ring
Aluminum Ferrule Spring
Coil Spring
Chuck Joint
Cross Plastic Spring
Delrin Fitting
Spring Holder
Coil Spring
Set Ring
Roller Rings
Roller
Roller Rings
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Flat Washer
Thrust Bearing Ring
Ball for Thrust Ring
Flat Washer
Motor Cover
Motor Stem
Small Screw
830zz Front Motor Bearing
Flat Washer
Motor Spring
Magnetic Steel Rotor
830zz Rear Motor Bearing
Motor Housing
Terminal Clip
Plastic Motor Fitting
Housing Screw
Motor End Cap Cover
Coiled Cord Assy 1.5m
Air Tri-Nut
Screws for Cord Connector
Cord Connector
U For Cord Connector
LAB TYPE HANDPIECE

6
SLIM TYPE HANDPIECE
5
Model Rotate Speed Max Torque Lock Tool Intensity Dimension N.W Cord Length Concentricity
BP50 1000-50,000 8.5N-CM 4.5-5.5kg 152*17.72mm 200g 1.5m 0.015mm

7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Nose Tip
Spindle Housing
Chuck
C-Clip
Dust Shield A
Dust Shield B
Flat Washer
Flat Washer
1260zz Bearing
Spindle Bushing
1480zz Bearing
Chuck Case
Aluminum Spring Ring
Short Coil Spring
Long Coil Spring
Chuck Joint
Short Coil Spring
Delrin Joint
Spring Cover
Spring
Set Ring
Roller Ring
Roller for Roller Ring
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Flat Washer
Thrust Bearing Ring
Ball for Thrust Ring
Flat Washer
Motor Cover
Motor Stem
Screws
Motor Cover for Bearing
830zz Bearing
Rubber Ring
Motor Spring
Magnetic Steel Rotor
830zz Bearing
Motor Housing
Plastic Motor Fitting
Housing Screw
Terminal Clip
Motor End Cap Cover
Coiled Cord Assy 1.5m
Air Tri-Nut
Cord Connector
Screws For Cord Connector
U For Cord Connector
8
Model Rotate Speed Max Torque Lock Tool Intensity Dimension N.W Cord Length Concentricity
BP50 1000-50,000 7.5N-CM 4.5-5.5kg 152*17.72mm 200g 1.5m 0.015mm

Ram Website BP50 Warranty Card
Registration
Customer Service
Request Form
How to Change
Collet Chucks
How to Disassemble
and Change All Bearings
9For using any of the
products, observe the operating
instructions given in each manual.
10 Never use for any purpose
other than the original one, nor
remodel it.
12 Never leave your Motor Handpiece
with the switch turned on,
an accident may occur if it is
over-heated.
11 Store in a dry place and
shielded from exposure to direct
sunlight. Store your in a place
with the lowest possible humidity
and moisture content. Never miss
daily inspection and maintenance.
8When taking your from the
box, never let it tumble out or fall
on the floor.
Handle any product that is
heavy or with sharp corners with
special care.
7If any abnormal vibration begins
during use, stop operating your
tool and remove the cause.
10
4When mounting any kind of bur to
your handpiece, insert it properly
to the final depth. Secure proper
mounting of the bur with the
correct amount of overhang.
5Use suitable speed that has not
exceeded the maximum value.
Exceeding the motor’s
maximum speed may invite trouble
including vibrations.
6When using your , wear safety
goggles/glasses and dust respirators
without fail. Flying chips may hurt
you when grinding workpieces with
hard materials. Use a coolant when
grinding a workpiece at high or
superhigh speed. Never touch tools
with sharp edges directly.
2Do not drop the product.
Dropping the motor may damage
the ball bearing or weaken the
durability of the motor.
3Inspect your before use
without fail. Before using your
, through visual inspection,
make sure that your has no
flaw, crack or faulty adhesion .
1Select the tools of product
after examining the following
conditions:
• Grinding tool performance
• Workpieces to be ground
• Grinding method
Safety Speed Table Guidelines
9
•Never use bent or damaged burs
•Do not force any burs into the collet chuck and always check after insertion the bur is securely locked by
pulling the bur
•Always operate at a safe speed for the size and weight of the bur. Start at 0 while slowly increasing speed and
securely gripping the handpiece. Operating at higher speeds often does not cut any better or faster and can
increase wear on the bearings in the handpiece as well as the cutting tool
•Follow basic safe speed operation according to the chart below and also the safety speed ratings of
manufacturer of the burs.
•Never operate without a bur properly locked in the handpiece
•After usage remove any excess dust or debris
•Do not operate near water or moisture.
•Avoid any chemicals and disinfectants.
This chart for allowable rotation speed can be slightly different depending on bur materials or bur type.
Rotating Speed (rpm)
Bur Size (diameter)
50,000
45,000
40,000
35,000
30,000
25,000
20,000
15,000
10,000
5,000
Larger
than Ø40
Smaller
than Ø2
Ø28-40 Ø18-28 Ø8-18 Ø4-8 Ø2-4
Always keep the proper rotating speed
per diameter of bur for your safety.
!
MAINTENANCE
Safety Precautions!

www.ramhp.com
1-732-651-5500 www.ramhp.com
[email protected]
1-732-651-6688
182 Ridge Road Suite D, Dayton, NJ 08810
WARRANTY PERIOD
PRODUCT WARRANTY
WARRANTY CLAIMS
Warranty is valid within the United States only.
ELECTRICAL EQUIPMENT - These products are under warranty for a
period of ONE YEAR from the date of original installation by the
purchaser.
HANDPIECES - These products are under warranty for a period of SIX
MONTHS from the date of original installation by the purchaser. IT DOES
NOT COVER MISUSE, NORMAL BEARING, OR CARBON BRUSH WEAR.
IN HOUSE OR FACTORY REPAIR - Repairs made under warranty will
be honored until the completion of the original product warranty
period. SHIPPING AND HANDLING CHARGES ARE NOT COVERED
WITHIN THE WARRANTY.
All returned items shall be free from defects/alterations in material,
workmanship and original product design.
• The product shall have been used under the conditions for which it
has been intended, and in a manner for which it has been designed.
• The product shall have been operated in a manner for which it was
intended and in the proper environmental conditions.
• The customer must maintain the product as specified within the
individual product instruction booklet.
Electrical and mechanical equipments and accessories which are
mishandled, used incorrectly, and/or used for a purpose other than
that for which they were designed and intended, will void the product
warranty.
Should your product require service attention within the warranty
period, we will elect to make the necessary repair or replacement at
no charge and providing the product is delivered prepaid to the
proper address. However it is recommended that returns be
adequately insured against carrier loss or damage.
All claims should describe the specific problem for accurate analysis
and evaluation, the return date of the warranty card along with the
supply house and/or dealer name.
No product replacement is permitted without prior authorization.
PRODUCT:
SERIAL NO.:
PURCHASE FROM:
PURCHASE DATE:
INSTALLATION DATE:
WARRANTY REGISTRATION
REGISTER ONLINE at www.ramhp.com/t-warranty-4.aspx
In order to validate your warranty, this card must be filled out
completely and mailed within 10 days of purchase/installation.
PLEASE PRINT OR TYPE
NAME:
ADDRESS.:
CITY:
STATE: ZIP CODE:
PRODUCT:
CITY:
SERIAL NO(S).:
PURCHASE DATE:
INSTALLATION DATE:
DEALER OR SUPPLY HOUSE NAME AND ADDRESS:
The short survey below is designed to improve the service and quality
of product supplied to our customers. Please take a few minutes to
complete the survey.
Did the item arrive in a satisfactory condition? YES or NO?
If NO please explain:
Did the instruction manual provide all details clearly for proper
installation and operation? YES or NO? If NO please explain:
What factor(s) were involved in your decision to purchase this product:
Advertisement Previous Purchase of a Ram Product
Distributor Recommendation Recommendation by Colleague
Any feedback, comments or suggestions:
Thank you for your feedback.