Rand McNally AssetTracker S100 User manual

3
Don’t install device on the
white area of the sides.
Don’t install the device
on the rear doors.
3
2
2
2
Don’t install the device on the
white area of the trailer roof.
1
1
1
Asset Tracker mounting locations guidelines for most dry van trailers:
Along the front edge or the rear edge of the roof (Green area) with the Rand McNally logo
towards the outside as the arrow indicates above. This is an ideal mounting location. Fig. 1
Along the left edge or the right edge of the roof (Yellow area) with the Rand McNally logo
towards the outside as the arrow indicates above. This is an acceptable mounting location
but less than ideal for GPS. Fig. 2
Along the top edge of either side panel or front panel (Orange area) with the Rand McNally
logo towards the sky as the arrow indicates above. This is an ideal mounting location for
B100 but severely reduces the charging efficiency of S100.
All other areas should be avoided as placement there degrades GPS performance
or expose the device to potential damage
Mounting install locations
Fig. 1
Fig. 2
AssetTrackerTM
Installation Manual

Surface Preparation and Installation
1. The box contains provisions for screw
mounting and adhesive mounting. It is
highly advised to install the Asset Tracker
using the screw mounting option as it is
more reliable and ensures securing the
device to the asset.
2. Choose a location that has a flat and even
surface. Avoid mounting the device on
glue or adhesive residues used to join/seal
the roofing panel material to the frame.
3. Choose a location that provides a
thick structural element on the trailer,
such as roof bows, top side rails, rear
frame, or top front nose rail. This
will provide adequate depth for the
provided fasteners.
4. Avoid using the self drilling screws with
thin gauge roof panel(s) as it doesn’t
provide enough thread engagement for
the fasteners.
5. Fiberglass roof panels are a much less
desirable surface to attach the self drilling
screws. Avoid driving screws in them as
they tend to flake and will not hold the
screws over time.
6. Place the washer between the screw
head and the mounting flange. Using
the proper drive bit, slowly drive the screw
into the metal surface. Provided screws
are #6-20 x ¾" self tapping galvanized
steel screws.
7. If you can’t use screw mounting and
you have to use double adhesive tape
mounting, please ensure the below
preparation steps.
8. At room temperature, the tape is 50%
cured after 20 minutes, 90% after 24
hours, 100% after 72 hours. Minimum
temperature for installation is 65°F
until 100% cured. If you cannot
meet this criteria, please do not use
adhesive tape.
9. Choose a flat even surface that is
smooth and non-porous such as a bare
aluminum or steel surface. If the surface
is painted, make sure the paint is intact
and not deteriorated or flaking off.
10. Thoroughly clean the surface with a
mixture of isopropyl alcohol (IPA) and
water (50% to 70% IPA). Wipe the
surface dry and make sure it’s free of
oil, grease, dust, or debris. NOTE: if the
surface is not thoroughly clean or has
debris on it, the adhesive tape becomes
ineffective.
11. Apply the tape to the surface, remove
the backing tape, then press and hold
the Asset Tracker onto the tape, keep
applying pressure for 30 seconds.
The following should be considered when mounting the Asset Tracker:
Asset Tracker Specifications
Dimensions:
3.96" L x 1.33" H x 2.33" W
Weight:
5.11 oz.
Operating temperature:
-40ºC to 85 ºC (-40ºF to 185ºF)
Dimensions:
3.96" L x 1.33" H x 2.33" W
Weight:
6.0 oz.
Operating temperature:
-20ºC to 60ºC (-4ºF to 149ºF)
Solar charging:
• Needs 24 hours of sunlight
to be fully charged
• Tracker can operate for
90 days without re-charging
Installation by customer required. Rand McNally is not responsible for any damage or injury caused by installation.
©2020 Rand McNally. Rand McNally, the globe logo, AssetTracker S100 and AssetTracker B100 are trademarks of RM Acquisition, LLC d/b/a/ Rand McNally.