R&S SMBV100B User manual

R&S®SMBV100B
Vector Signal Generator
Getting Started
Getting Started
Version 05
1423104902
(>G:a2)

This document describes the R&S®SMBV100B, stock no. 1423.1003.02 and its
options.
© 2019 Rohde & Schwarz GmbH & Co. KG
Mühldorfstr. 15, 81671 München, Germany
Phone: [phone] - 0
Fax: [phone]
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – Data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
1423.1049.02 | Version 05 | R&S®SMBV100B
The following abbreviations are used throughout this manual: R&S®SMBV100B is abbreviated as
R&S SMBV100B, R&S®WinIQSIM2TM is abbreviated as R&S WinIQSIM2, R&S®VISA is abbreviated as
R&S VISA.

Contents
R&S®SMBV100B
3Getting Started 1423.1049.02 ─ 05
Contents
1 Preface....................................................................................7
1.1 Key Features......................................................................................... 7
2 Safety and Regulatory Information...................................... 9
2.1 Safety Instructions................................................................................9
2.2 Labels on R&S SMBV100B.................................................................12
2.3 Korea Certification Class A................................................................12
3 Documentation Overview....................................................13
3.1 Getting Started Manual.......................................................................13
3.2 User Manuals and Help...................................................................... 13
3.3 Service Manual....................................................................................14
3.4 Instrument Security Procedures....................................................... 14
3.5 Basic Safety Instructions................................................................... 14
3.6 Data Sheets and Brochures............................................................... 14
3.7 Release Notes and Open Source Acknowledgment (OSA).............15
3.8 Application Notes, Application Cards, White Papers, etc...............15
4 Preparing for Use.................................................................17
4.1 Lifting and Carrying............................................................................17
4.2 Unpacking and Checking................................................................... 17
4.3 Choosing the Operating Site............................................................. 18
4.4 Setting Up the R&S SMBV100B......................................................... 18
4.4.1 Placing the R&S SMBV100B on a Bench Top...................................... 18
4.4.2 Mounting the R&S SMBV100B in a Rack............................................. 19
4.5 Important Aspects for Test Setup......................................................20
4.6 Connecting to Power.......................................................................... 22

Contents
R&S®SMBV100B
4Getting Started 1423.1049.02 ─ 05
4.7 Connecting to LAN............................................................................. 22
4.8 Connecting USB Devices................................................................... 23
4.9 Connecting to RF................................................................................ 24
4.10 Connecting to LO In/Out.................................................................... 24
4.11 Connecting to Ref In/Ref Out.............................................................25
4.12 Connecting to HS Dig I/Q................................................................... 26
4.13 Switching On or Off............................................................................ 27
5 Instrument Tour................................................................... 31
5.1 Front Panel Tour..................................................................................31
5.1.1 Touchscreen..........................................................................................32
5.1.2 Keys...................................................................................................... 33
5.1.2.1 Utility Keys............................................................................................ 33
5.1.2.2 On/Standby........................................................................................... 33
5.1.2.3 Function Keys....................................................................................... 34
5.1.2.4 Keypad..................................................................................................34
5.1.2.5 Editing Keys.......................................................................................... 35
5.1.2.6 Navigation Controls...............................................................................35
Rotary Knob.......................................................................................... 35
Navigation Keys.................................................................................... 36
Display Keys......................................................................................... 36
5.1.3 Connectors............................................................................................37
5.2 Rear Panel Tour...................................................................................38
5.2.1 Connectors............................................................................................39
6 Trying Out the Instrument...................................................43
6.1 Generating an Unmodulated Carrier................................................. 43
6.2 Generating a Digitally Modulated Signal.......................................... 46
6.3 Triggering the Instrument with an External Signal.......................... 48

Contents
R&S®SMBV100B
5Getting Started 1423.1049.02 ─ 05
6.4 Enabling and Configuring a Marker Signal...................................... 54
6.5 Verifying the Generated Signal with the Graphics Display............. 55
6.6 Saving and Recalling Settings...........................................................58
6.7 Generating an EUTRA/LTE Signal..................................................... 61
7 System Overview................................................................. 67
7.1 Brief Introduction to the Instrument's Concept............................... 67
7.2 Signal Flow at a Glance......................................................................67
7.3 Internal Baseband Source ("Baseband" Block)...............................69
7.4 Digital Baseband Input ("BB Input"Block)....................................... 69
7.5 Additional White Gaussian Noise ("AWGN" Block)......................... 70
7.6 "I/Q Stream Mapper" Block................................................................ 70
7.7 I/Q Modulator ("I/Q Mod" Block)........................................................ 70
7.8 Analog I/Q Output ("I/Q Analog" Block)............................................71
7.9 RF and Analog Modulations ("RF" Block)........................................ 71
7.10 Applications Examples of the R&S SMBV100B............................... 71
8 Instrument Control.............................................................. 73
8.1 Possible Ways to Operate the Instrument........................................ 73
8.2 Means of Manual Interaction..............................................................74
8.3 Understanding the Display Information............................................75
8.3.1 Status Bar............................................................................................. 75
8.3.2 Block Diagram.......................................................................................76
8.3.3 Taskbar................................................................................................. 77
8.3.4 Additional Display Characteristics.........................................................78
8.4 Accessing the Functionality.............................................................. 80
8.5 Entering Data.......................................................................................82
8.5.1 Entering Numeric Parameters...............................................................82
8.5.2 Entering Alphanumeric Parameters...................................................... 83

Contents
R&S®SMBV100B
6Getting Started 1423.1049.02 ─ 05
8.5.3 Undo and Redo Actions........................................................................ 83
8.6 Getting Information and Help............................................................ 83
8.7 Remote Control................................................................................... 85
8.8 Remote Operation over VNC..............................................................86
9 Contacting Customer Support........................................... 87
Index..................................................................................... 89

Preface
R&S®SMBV100B
7Getting Started 1423.1049.02 ─ 05
1 Preface
The R&S SMBV100B is a new signal generator developed to meet demanding
customer requirements. Offering excellent signal characteristic and straightfor-
ward and intuitive operation, the signal generator makes signal generation fast
and easy.
1.1 Key Features
The R&S SMBV100B is a new high-performance signal generator developed to
meet demanding customer requirements. Offering excellent signal characteristic
and straightforward and intuitive operation, the signal generator makes signal
generation fast and easy.
Outstanding key features of the R&S SMBV100B are:
●Frequency range from 8 kHz to 6 GHz
●Up to 500 MHz I/Q modulation bandwidth (in RF) with internal baseband
●Support of all important digital standards such as LTE incl eMTC/NB-IoT, 5G
NR, WLAN IEEE 802.11a/b/g/n/j/p/ac/ax, 3GPP FDD/HSPA/HSPA+
●Excellent signal quality for high accuracy in spectral and modulation measure-
ments
●Intuitive operation via touchscreen with block diagram as key element
●Graphical signal monitoring at practically every point in the signal flow
●SCPI macro recorder and code generator for generating executable remote
control code from manual operating steps (for MATLAB®, CVI, etc.)
For more information, see data sheet.
Key Features

Preface
R&S®SMBV100B
8Getting Started 1423.1049.02 ─ 05
Key Features

Safety and Regulatory Information
R&S®SMBV100B
9Getting Started 1423.1049.02 ─ 05
2 Safety and Regulatory Information
The product documentation helps you use the R&S SMBV100B safely and effi-
ciently. Follow the instructions provided here and in the Chapter 2.1, "Safety
Instructions", on page 9.
Intended use
The R&S SMBV100B is intended for the development, production and verification
of electronic components and devices in industrial, administrative, and laboratory
environments. Use the R&S SMBV100B only for its designated purpose. Observe
the operating conditions and performance limits stated in the data sheet.
Where do I find safety information?
Safety information is part of the product documentation. It warns you of potential
dangers and gives instructions on how to prevent personal injury or damage
caused by dangerous situations. Safety information is provided as follows:
●In Chapter 2.1, "Safety Instructions", on page 9. The same information is
provided in many languages as printed "Safety Instructions". The printed
"Safety Instructions" are delivered with the R&S SMBV100B.
●Throughout the documentation, safety instructions are provided when you
need to take care during setup or operation.
2.1 Safety Instructions
Products from the Rohde & Schwarz group of companies are manufactured
according to the highest technical standards. To use the products safely, follow
the instructions provided here and in the product documentation. Keep the prod-
uct documentation nearby and offer it to other users.
Use the product only for its intended use and within its performance limits. Inten-
ded use and limits are described in the product documentation such as the data
sheet, manuals and the printed safety instructions. If you are unsure about the
appropriate use, contact Rohde & Schwarz customer service.
Using the product requires specialists or specially trained personnel. These users
also need sound knowledge of at least one of the languages in which the user
interfaces and the product documentation are available.
Safety Instructions

Safety and Regulatory Information
R&S®SMBV100B
10Getting Started 1423.1049.02 ─ 05
If any part of the product is damaged or broken, stop using the product. Never
open the casing of the product. Only service personnel authorized by
Rohde & Schwarz are allowed to repair the product. Contact Rohde & Schwarz
customer service at http://www.customersupport.rohde-schwarz.com.
Lifting and carrying the product
Some products are heavy. A safety label on the casing indicates if a product
weighs more than 18 kg. To safely move the product, you can use lifting or trans-
porting equipment such as lift trucks, cranes, forklifts and hand trucks. Secure the
product, but not by its handles. Excessive force can break the handles.
Choosing the operating site
Only use the product indoors. The product casing is not waterproof and water that
enters can electrically connect the casing with live parts. This can lead to electric
shock, serious personal injury or death if you touch the casing.
Unless otherwise specified, you can operate the product up to an altitude of
2000 m above sea level. The product is suitable for pollution degree 2 environ-
ments where nonconductive contamination can occur. For more information on
environmental conditions such as ambient temperature and humidity, see the
data sheet.
Setting up the instrument
Always place the instrument on a stable, flat and level surface with the bottom of
the instrument facing down.
To save space, you can mount several instruments in a rack. If you stack instru-
ments, keep in mind that a stack of instruments can tilt over and cause injury.
If the instrument has foldable feet, always fold the feet completely in or out to
ensure stability. The feet can collapse if they are not folded out completely or if
the instrument is moved without lifting it. The foldable feet are designed to carry
the weight of the instrument, but not an extra load.
Connecting to power
The product is an overvoltage category II product and has to be connected to a
fixed installation used to supply energy-consuming equipment such as household
appliances and similar loads. Be aware that electrically powered products have
risks, such as electric shock, fire, personal injury or even death.
Safety Instructions

Safety and Regulatory Information
R&S®SMBV100B
11Getting Started 1423.1049.02 ─ 05
Take the following measures for your safety:
●Before switching on the product, ensure that the voltage and frequency indica-
ted on the product match the available power source. If the power adapter
does not adjust automatically, set the correct value and check the rating of the
fuse.
●If a product has an exchangeable fuse, its type and characteristics are indica-
ted next to the fuse holder. Before changing the fuse, switch off the instrument
and disconnect it from the power source. How to change the fuse is described
in the product documentation.
●Only use the power cable delivered with the product. It complies with country-
specific safety requirements. Only insert the plug into an approved grounded
outlet.
●Only use intact cables and route them carefully so that they cannot be dam-
aged. Check the power cables regularly to ensure that they are undamaged.
Also ensure that nobody can trip over loose cables.
●If the product needs an external power supply, use the power supply that is
delivered with the product or that is recommended in the product documenta-
tion or a power supply that conforms to the country-specific regulations.
●Only connect the product to a power source with a fuse protection of maxi-
mum 20 A.
●Ensure that you can disconnect the product from the power source at any
time. Pull the power plug to disconnect the product. The power plug must be
easily accessible. If the product is integrated into a system that does not meet
these requirements, provide an easily accessible circuit breaker at the system
level.
Cleaning the product
Use a dry, lint-free cloth to clean the product. When cleaning, keep in mind that
the casing is not waterproof. Do not use liquid cleaning agents.
Meaning of safety labels
Safety labels on the product warn against potential hazards.
Safety Instructions

Safety and Regulatory Information
R&S®SMBV100B
12Getting Started 1423.1049.02 ─ 05
Potential hazard
Read the product documentation to avoid personal injury or product damage.
Heavy product
Be careful when lifting, moving or carrying the product. Carrying the product requires
at least two people or transport equipment.
Electrical hazard
Indicates live parts. Risk of electric shock, fire, personal injury or even death.
Hot surface
Do not touch. Risk of skin burns. Risk of fire.
Protective conductor terminal
Connect this terminal to a grounded external conductor or to protective ground. This
protects you against electric shock should an electric problem occur.
2.2 Labels on R&S SMBV100B
Labels on the casing inform about:
●Personal safety, see "Connecting to power" on page 10.
●Product and environment safety, see Table 2-1.
●Identification of the product, see the serial number on the rear panel.
Table 2-1: Labels regarding R&S SMBV100B and environment safety
Labeling in line with EN 50419 for disposal of electrical and electronic equipment after
the product has come to the end of its service life. For more information, see the prod-
uct user manual, chapter "Disposal".
2.3 Korea Certification Class A
이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하
시기 바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.
Korea Certification Class A

Documentation Overview
R&S®SMBV100B
13Getting Started 1423.1049.02 ─ 05
3 Documentation Overview
This section provides an overview of the R&S SMBV100B user documentation.
Unless specified otherwise, you find the documents on the R&S SMBV100B prod-
uct page at:
www.rohde-schwarz.com/manual/smbv100b
3.1 Getting Started Manual
Introduces the R&S SMBV100B and describes how to set up and start working
with the product. Includes basic operations, typical measurement examples, and
general information, e.g. safety instructions, etc. A printed version is delivered
with the instrument.
3.2 User Manuals and Help
Separate manuals for the base unit and the software options are provided for
download:
●Base unit manual
Contains the description of all instrument modes and functions. It also pro-
vides an introduction to remote control, a complete description of the remote
control commands with programming examples, and information on mainte-
nance, instrument interfaces and error messages. Includes the contents of the
getting started manual.
●Software option manual
Contains the description of the specific functions of an option. Basic informa-
tion on operating the R&S SMBV100B is not included.
All user manuals are also available for download or for immediate display on the
Internet.
User Manuals and Help

Documentation Overview
R&S®SMBV100B
14Getting Started 1423.1049.02 ─ 05
3.3 Service Manual
Describes the performance test for checking the rated specifications, module
replacement and repair, firmware update, troubleshooting and fault elimination,
and contains mechanical drawings and spare part lists.
The service manual is available for registered users on the global
Rohde & Schwarz information system (GLORIS, https://gloris.rohde-
schwarz.com).
3.4 Instrument Security Procedures
Deals with security issues when working with the R&S SMBV100B in secure
areas. It is available for download on the Internet.
3.5 Basic Safety Instructions
Contains safety instructions, operating conditions and further important informa-
tion. The printed document is delivered with the instrument.
3.6 Data Sheets and Brochures
The data sheet contains the technical specifications of the R&S SMBV100B. It
also lists the options and their order numbers and optional accessories.
The brochure provides an overview of the instrument and deals with the specific
characteristics.
See www.rohde-schwarz.com/brochure-datasheet/smbv100b
Data Sheets and Brochures

Documentation Overview
R&S®SMBV100B
15Getting Started 1423.1049.02 ─ 05
3.7 Release Notes and Open Source Acknowledg-
ment (OSA)
The release notes list new features, improvements and known issues of the cur-
rent firmware version, and describe the firmware installation.
The open source acknowledgment document provides verbatim license texts of
the used open source software.
See www.rohde-schwarz.com/firmware/smbv100b
3.8 Application Notes, Application Cards, White
Papers, etc.
These documents deal with special applications or background information on
particular topics.
See www.rohde-schwarz.com/application/smbv100b
Application Notes, Application Cards, White Papers, etc.

Documentation Overview
R&S®SMBV100B
16Getting Started 1423.1049.02 ─ 05
Application Notes, Application Cards, White Papers, etc.

Preparing for Use
R&S®SMBV100B
17Getting Started 1423.1049.02 ─ 05
4 Preparing for Use
This chapter describes the basic steps to be taken when setting up the
R&S SMBV100B for the first time.
4.1 Lifting and Carrying
See also "Lifting and carrying the product" on page 10.
► Use the carrying handle at the side for lifting and carrying the
R&S SMBV100B.
For mounting the R&S SMBV100B in a rack, see Chapter 4.4.2, "Mounting the
R&S SMBV100B in a Rack", on page 19.
4.2 Unpacking and Checking
1. Unpack the R&S SMBV100B carefully.
2. Retain the original packing material. Use it to protect the control elements and
connectors when transporting or shipping the R&S SMBV100B later.
See also chapter "Transporting" in the user manual.
3. Using the delivery notes, check the equipment for completeness.
4. Check the equipment for damage.
If the delivery is incomplete or equipment is damaged, contact
Rohde & Schwarz.
Unpacking and Checking

Preparing for Use
R&S®SMBV100B
18Getting Started 1423.1049.02 ─ 05
4.3 Choosing the Operating Site
Specific operating conditions ensure accurate measurements and avoid damage
to the R&S SMBV100B and connected devices. For information on environmental
conditions such as ambient temperature and humidity, see the data sheet.
See also "Choosing the operating site" on page 10.
Electromagnetic compatibility classes
The electromagnetic compatibility (EMC) class indicates where you can operate
the R&S SMBV100B. The EMC class of the R&S SMBV100B is given in the data
sheet under "General data".
●Class B equipment is suitable for use in:
– Residential environments
– Environments that are directly connected to a low-voltage supply network
that supplies residential buildings
●Class A equipment is intended for use in industrial environments. It can cause
radio disturbances in residential environments due to possible conducted and
radiated disturbances. It is therefore not suitable for class B environments.
If class A equipment causes radio disturbances, take appropriate measures to
eliminate them.
4.4 Setting Up the R&S SMBV100B
See also:
●"Setting up the instrument" on page 10.
●"Intended use" on page 9.
4.4.1 Placing the R&S SMBV100B on a Bench Top
To place the R&S SMBV100B on a bench top
1. Place the R&S SMBV100B on a stable, flat and level surface. Ensure that the
surface can support the weight of the R&S SMBV100B. For information on the
weight, see the data sheet.
Setting Up the R&S SMBV100B

Preparing for Use
R&S®SMBV100B
19Getting Started 1423.1049.02 ─ 05
2. CAUTION! Foldable feet can collapse. See "Setting up the instrument"
on page 10.
Always fold the feet completely in or out. With folded-out feet, do not place
anything on top or underneath the instrument.
3. WARNING! A stack of instruments can fall over and cause injury. Never stack
more than three instruments on top of each other. Instead, mount them in a
rack.
Stack as follows:
● It is best if all instruments have the same dimensions (width and length).
● The overall load on the lowest instrument must not exceed 500 N.
● With smaller instruments on top of the lowest instrument, the overall load
on the lowest instrument must not exceed 250 N.
Too many instruments
max. 500 N
Correct Different dimensions
max. 250 N
4. NOTICE! Overheating can damage the R&S SMBV100B.
Prevent overheating as follows:
● Keep a minimum distance of 10 cm between the fan openings of the
R&S SMBV100B and any object in the vicinity.
● Do not place the R&S SMBV100B next to heat-generating equipment such
as radiators or other instruments.
4.4.2 Mounting the R&S SMBV100B in a Rack
To prepare the rack
1. Observe the requirements and instructions in "Setting up the instrument"
on page 10.
2. NOTICE! Insufficient airflow can cause overheating and damage the
R&S SMBV100B.
Setting Up the R&S SMBV100B

Preparing for Use
R&S®SMBV100B
20Getting Started 1423.1049.02 ─ 05
Design and implement an efficient ventilation concept for the rack.
To mount the R&S SMBV100B in a rack
1. Use an adapter kit that fits the dimensions of the R&S SMBV100B to prepare
the instrument for rack mounting. For information on the dimensions, see data
sheet.
a) Order the rack adapter kit designed for the R&S SMBV100B. For the order
number, see data sheet.
b) Mount the adapter kit. Follow the assembly instructions provided with the
adapter kit.
2. Lift the R&S SMBV100B to shelf height.
3. Grab the handles and push the R&S SMBV100B onto the shelf until the rack
brackets fit closely to the rack.
4. Tighten all screws at the rack brackets with a tightening torque of 1.2 Nm to
secure the R&S SMBV100B at the rack.
To unmount the R&S SMBV100B from a rack
1. Loosen the screws at the rack brackets.
2. Bring the lifting equipment to shelf height.
3. Remove the R&S SMBV100B from the rack.
4. If placing the R&S SMBV100B on a bench top again, unmount the adapter kit
from the R&S SMBV100B. Follow the instructions provided with the adapter
kit.
4.5 Important Aspects for Test Setup
Cable selection and electromagnetic interference (EMI)
Electromagnetic interference (EMI) can affect the measurement results.
To suppress electromagnetic radiation during operation:
●Use high-quality shielded cables, especially for the following connector types:
– BNC
Double-shielded BNC cables.
Important Aspects for Test Setup