R&S SpycerBox Cell Installation instructions

SpycerBox Cell Hardware Guide (Version 1.0)
Storage Solution
R&S®SpycerBox Cell
Hardware Guide

SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH

SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Hardware Guide Version 1.0 for the SpycerBox Cell (hardware version 1.0)
Copyright © 2014 by Rohde & Schwarz DVS GmbH, Hanover. All rights reserved.
The manuals as well as the soft- and/or hardware described here and all their constituent parts are
protected by copyright. Without the express permission of Rohde & Schwarz DVS GmbH any form
of use which goes beyond the narrow bounds prescribed by copyright legislation is prohibited and
liable to prosecution.
This particularly applies to duplication, copying, translation, processing, evaluation, publishing, and
storing and/or processing in an electronic system.
Specifications and data may change without notice. We offer no guarantee that this documentation
is correct and/or complete. In no event shall Rohde & Schwarz DVS GmbH be liable for any damages
whatsoever (including without limitation any special, indirect or consequential damages, and dam-
ages resulting from loss of use, data or profits, or business interruption) arising out of the use of or
inability to use the hardware, software and/or manual materials.
Those parts of this documentation that describe optional software or hardware features usually con-
tain a corresponding note. Anyway, a lack of this note does not mean any commitment from
Rohde & Schwarz DVS GmbH.
DVS and Spycer are registered trademarks of Rohde & Schwarz DVS GmbH. Linux is a registered
trademark of Linus Torvalds.
Any other product names mentioned in this documentation may be trademarks or registered trade-
marks of their respective owners and as such are subject to the usual statutory provisions.

SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Headquarters:
Support:
Rohde & Schwarz DVS GmbH
Krepenstr. 8
30165 Hannover
GERMANY
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Internet: http://www.dvs.de
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

C-iSpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Contents
Contents
1Introduction ...............................................................................1-1
1.1 Target Group ...........................................................................1-1
1.2 Conventions Used in this User Guide ..................................... 1-1
1.3 Safety Instructions ..................................................................1-4
1.4 Important Notes ......................................................................1-6
2Overview ......................................................................................2-1
2.1 Variants of the SpycerBox Cell ................................................2-2
2.2 Overview of the Front..............................................................2-3
2.2.1 Faceplate ...................................................................... 2-4
2.2.2 Hard Disk Tray ...............................................................2-6
2.3 Overview of the Rear...............................................................2-8
2.3.1 Power Supply ................................................................2-9
2.3.2 Controller Module ........................................................ 2-10
2.3.3 Expansion Panel ..........................................................2-13
2.4 Battery Backup Unit .............................................................. 2-14
3Installation ..................................................................................3-1
3.1 System Setup .......................................................................... 3-2
3.2 Note about the Network Installation .......................................3-3
4Operation .....................................................................................4-1
4.1 Starting the System.................................................................4-2
4.2 R&S DVS SAN Remo...............................................................4-3
4.3 Shutting Down the System .....................................................4-4

Contents
C-ii
SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
5Maintenance ..............................................................................5-1
5.1 Hard Disk Maintenance ...........................................................5-2
5.1.1 Introduction to RAID ......................................................5-2
5.1.2 Identifying a Broken Hard Disk ........................................5-4
5.1.3 Replacing a Hard Disk ....................................................5-5
5.2 Fan Failure Management.......................................................5-10
5.3 Controller Maintenance .........................................................5-13
5.4 Power Supply Maintenance...................................................5-19
5.5 Backup or Recovery of the System Disk ...............................5-21
5.5.1 Creating a Backup Image of the System Disk .................5-21
5.5.2 Restoring the System Disk ............................................5-23
AAppendix ..................................................................................... A-1
A.1 Troubleshooting ...................................................................... A-2
A.2 Technical Data ........................................................................ A-5
A.2.1 General Technical Data .................................................. A-5
A.2.2 Dimensions .................................................................. A-6
A.3 Packing Instructions ............................................................... A-7
A.4 Conformity Declarations ......................................................... A-9
A.4.1 RoHS Compliance ......................................................... A-9
A.4.2 EC Declaration of Conformity (CE Marking) ..................... A-9
A.4.3 FCC Compliance Statement ......................................... A-10
IIndex ...............................................................................................I-1

1-1SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Introduction
Introduction
1.1 Target Group
To use this manual you should know how to handle computer equip-
ment. Furthermore, to connect the R&S system to a network or a SAN
storage you should have experience as a network administrator and
know how to set up the required network connections on the installa-
tion site in hard- as well as software.
When performing maintenance tasks on the hardware of the R&S sys-
tem, you must be qualified to work on, repair and test electrical equip-
ment.
1.2 Conventions Used in this User Guide
The following typographical conventions will be used in this documen-
tation:
1. Texts preceded by this symbol describe activities that you must
perform in the order indicated.
Texts preceded by this symbol are parts of a list.
Texts preceded by this symbol are parts of a list of a second
level.
Texts preceded by this symbol are parts of a requirements list.
Texts preceded by this symbol describe the result of an action.
Texts preceded by this symbol are general notes intended to facilitate
work and help avoid errors.
Cause of Risk
Indicates the possibility of incorrect operation which can result in
damage to the product. You must pay particular attention to text
that follows this symbol to avoid errors.
Preventive measures to avoid risks of damage to the sys-
tem.

Introduction
Conventions Used in this User Guide
1-2
SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Source of Danger
Indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
Preventive measures to avoid minor or moderate in-
jury.
Source of Danger
Indicates a hazardous situation which, if not avoided, can
result in death or serious injury.
Preventive measures to avoid death or serious inju-
ry.
Source of Danger
Indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
Preventive measures to avoid death or serious injury.
“ ” Texts enclosed by quotation marks are references to other manuals, guides,
chapters, or sections.
’ ’ Texts enclosed by single quotation marks are references to labelings given
by the author and quoted labelings.
’Window’ Text in bold with single quotation marks indi-
cates a window name
BUTTON Text in small caps and bold indicates a push but-
ton
Group/Menu Text in italic and bold indicates either a group
name, menu name or options in a menu list
Menu > Option In the specified group or menu select the stated
item.
Item Text in bold only stands for other labeled items
of a user interface
Directory/File Directory structure or file
Entry Indicates parameters or variables, as well as se-
lections or entries made in a program; it may
also indicate a command (e.g. at a command
line), a syntax or contents of a file/output
[Key] An individual key or a key combination on a key-
board

1-3SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Introduction
Conventions Used in this User Guide
Keyboard Shortcuts
To perform options or procedures with the keyboard often requires a si-
multaneous pressing of two keys.
Example:
Screenshots
The screenshots shown in this documentation may be taken on various
operating systems as well as from pre-release versions of the software.
Their appearance may differ from your environment. However, they
should contain all relevant elements that you need to understand the
described actions.
[Ctrl + F1] If this is given, hold down the [Ctrl] key and
press simultaneously the [F1] key.
[Alt, F1] If this is given, press the [Alt] key first and then
the key [F1] successively.

Introduction
Safety Instructions
1-4
SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
1.3 Safety Instructions
To use the SpycerBox Cell correctly please heed the following:
General
The SpycerBox Cell has been built according to the applying safety reg-
ulations. To minimize the possibility of a faulty operation of the device
all manuals and guides must be available at all times at the operation
site. Before installing and/or using the R&S system the manuals and
guides delivered with it must be read and observed.
Use the R&S system only in apparent good technical order.
The hardware of the R&S system works with voltages that can be
hazardous to your health. Never work on the system or access its
interior with the power cable(s) being plugged in. Make sure the
power supply is disconnected from the components you intend to
work on.
Computer hardware contains components that are sensitive to elec-
trostatic discharge. If you touch them without precautionary mea-
sures, they can be destroyed. Use a wrist strap connected to
ground when accessing electronic parts and take care of grounding
the system. Avoid touching the internal components of the R&S
system whenever possible.
Computer hardware contains components that are sensitive to
changing voltages. Connecting or disconnecting the R&S system
to or from peripheral hardware while any of them is switched on
may damage the hardware. Switch off all peripheral hardware
before connecting or disconnecting anything.
Use, store and transport the R&S system only in compliance with
the technical data laid out in section “Technical Data” on page A-5.
If fluids or solid objects get inside the casing, the R&S system must
be disconnected from the power supply immediately. Before using
the R&S system again, it has to be checked by authorized service
personnel.
Only use a damp tissue without any cleaning agents to clean the
casing.
The R&S system must not be misused, abused, physically dam-
aged, neglected, exposed to fire, water or excessive changes in the
climate or temperature, or operated outside maximum rating.
Noncompliance with safety instructions
If the R&S system is not used in compliance with the safety instruc-
tions, the warranty and all resulting liability claims will be void.
Please read the following safety instructions carefully be-
fore attempting any installation and/or performing any work
on the SpycerBox Cell hardware.

1-5SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Introduction
Safety Instructions
Do not perform any changes or extensions to the R&S system what-
soever.
Transportation
The SpycerBox Cell is a very sensitive device. Especially the hard disks
of the system must be handled with great care. Therefore, observe in
case of transportation:
Handle the R&S system with great care.
Always use the original packing or a similar structured packing for
transportation as detailed in section “Packing Instructions” on
page A-7.
Avoid shocks or vibrations during transport. For longer distances it
is recommended to use a lifting truck.
Keep the R&S system as a transportation good dry.
In the warranty period you have to keep the original packing and
use it in case of transportation.
Environmental Conditions
For error-free working and a long service life the SpycerBox Cell needs
some basic environmental conditions:
Do not expose the R&S system to sources of heat, such as direct
sunlight or a radiator.
Do not cover or obstruct the ventilation holes of the system.
When installing the R&S system in a rack, take care that warmed up
air is conducted to the rear of the rack and properly vented away.
Avoid areas with high humidity or dust. Best operating conditions
are given in an air-conditioned site.
Do not expose the R&S system to strong electric or magnetic fields.
Avoid areas where the R&S system will be subject to vibrations or
shocks.

Introduction
Important Notes
1-6
SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
1.4 Important Notes
The following provides information about warranty, a note about the
conformity of the product and some other general information.
Warranty Information
This product is warranted to be free of defects in materials and work-
manship for a period of one year from the date of purchase. R&S ex-
tends this Limited Warranty to the original purchaser.
In the event of a defect or failure to confirm to this Limited Warranty,
R&S will repair or replace the product without charge. In order to make
a claim under this Limited Warranty, the purchaser must notify R&S or
their representative in writing of the product failure. In this Limited War-
ranty the customer must upon R&S DVS’s request return the product
to the place of purchase or send the defective device to a given address
for the necessary repairs to be performed. In the warranty period the
customer must keep the original packing and pack the R&S product in
it in case of a product return. If the customer is not satisfied with the
repair, R&S will have the option to either attempt a further repair, ex-
change the product or refund the purchase price.
This warranty does not cover:
Products not developed by Rohde & Schwarz DVS GmbH.
Products not used in compliance with the safety instructions
detailed in section “Safety Instructions” on page 1-4.
Products on which warranty stickers or product serial numbers
have been removed, altered or rendered illegible.
The costs of installations, removals, transportations, or reinstalla-
tions.
Costs for transportation damages.
Damages caused to any other item.
Any special, indirect or consequential damages, and damages
resulting from loss of use, data or profits, or business interruption.
Incorrect packaging
This warranty will be void if you do not transport the R&S device in
the original packing.
You have to keep the original packing and use it in case of
transportation.

1-7SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Introduction
Important Notes
Declaration of Conformity
This product has been tested according to the ap-
plying national and international directives and reg-
ulations. Further information about this can be
found in section “Conformity Declarations” on
page A-9.
Product Disposal (B2B)
Used electrical and electronic products should not be dis-
posed of with general household waste. At the end of its
service life you may return the R&S product after appro-
priate prior notification to either your local distributor or
R&S in Germany. R&S will then take the device free of
charge to a waste disposal organization which will recy-
cle and reuse it environmental friendly.
General Notes
Please observe the following general important notes:
Full storage
In case of a full storage performance losses may occur.
Leave about 10 to 15% of the overall main storage capacity
empty of data for performance reasons.
Installation of third-party software
Your R&S system has been tested thoroughly and is very reliable.
However, because of the vast amount of third-party software avail-
able, its reactions on the installation of such could not be tested.
The installation of third-party software may disrupt the real-time
capability and/or limit the functionality of your system.
When installing third-party software, make sure that it does
not interrupt and/or limit any functionality of the system.

Introduction
Important Notes
1-8
SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH

2-1SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Overview
Overview
Variants of the SpycerBox Cell ...............................................................2-2
Overview of the Front ............................................................................ 2-3
Faceplate ...........................................................................................2-4
Hard Disk Tray ...................................................................................2-6
Overview of the Rear .............................................................................2-8
Power Supply .....................................................................................2-9
Controller Module ............................................................................2-10
Expansion Panel ..............................................................................2-13
Battery Backup Unit ............................................................................. 2-14
Contents

Overview
Variants of the SpycerBox Cell
2-2
SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
2.1 Variants of the SpycerBox Cell
The SpycerBox Cell can be delivered in different hardware variants de-
pending on, for example, the amount of the storage or the performance
that is required. The following variants are available:
SpycerBox Cell SAS version
SpycerBox Cell SSD version
SpycerBox Cell SATA (enterprise or with SAS interface)
The following options are available:
Ethernet Option Fibre Channel Option
No additional Ethernet option (only
1×1Gbit/sonboard)
Quad-port Ethernet card (1 Gbit/s,
copper)
Dual-port Ethernet card (10 Gbit/s,
SFP+)
Dual-port Fibre Channel (16 Gbit/s)
Quad-port Fibre Channel (8 Gbit/s)
Quad-port Fibre Channel (16 Gbit/s)
You can combine each Ethernet option from the left column with each
Fibre Channel option from the right column above.
As the space at the rear of the SpycerBox Cell is limited, you can only
select one option from each column above.

2-3SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Overview
Overview of the Front
2.2 Overview of the Front
This section provides an overview of the front of the system:
Figure 2-1: Overview of the front
Item Explanation
faceplate/ The faceplate covers the hard disk tray. If you need ac-
cess to one of the hard disks, for example, to replace it,
it can be removed. The faceplate will be described in
more detail in section “Faceplate” on page 2-4.
The hard disk tray contains the main storage hard disks
which can be used to store video, audio or backup ma-
terial. All disks can be replaced easily in case of failure.
The disk array is described in more detail in section
“Hard Disk Tray” on page 2-6.
illuminated
display
The display is illuminated and shows an R&S logo when
the system is operating properly. Furthermore, you find
the system‘s IP address below the R&S logo. In case of
a hardware failure, the display shows a red warning/
alarm icon to inform you about this. In addition, an
alarm signal might be sounded, depending on the kind
of hardware failure, that can be switched mute using
the mute button.
For further information about what to do in case of a
hardware failure, see chapter “Maintenance” on
page 5-1 and section “Troubleshooting” on page A-2.
operation itemsfaceplate illuminated display

Overview
Overview of the Front
2-4
SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
2.2.1 Faceplate
The faceplate covers the hard disks of the hard disk tray. It is built with
an integrated R&S logo which indicates the systems power-on status:
If the R&S logo is illuminated, the power is turned on; if not, the power
is turned off. The front cooling fans are build inside the faceplate.
operation
items
power
With the operation items the system can be controlled
(e.g. turned on or off). The power switch (first button on
top) turns the system on or off. The respective state of
the system will be indicated by the R&S DVS logo in the
middle of the faceplate (see section “Faceplate” on
page 2-4).
mute
In case of a hardware malfunction a system alarm turns
on. By pressing the mute button (below the power but-
ton), the alarm buzzer can be switched mute.
The operating system must be fully load-
ed to switch an alarm mute.
Further information about what to do in case of an alarm can be found
in section “Troubleshooting” on page A-2.
The system must be operated only with the faceplate installed to ensure
proper cooling.
In case you have to exchange a hard disk, you can remove the faceplate
for a maximum of the time the hard disk exchange will take.
Item Explanation

2-5SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
Overview
Overview of the Front
Removing the faceplate
If you need access to one of the hard disks, for example, to replace it,
you just have to remove the faceplate:
Figure 2-2: Removing the faceplate
To remove the faceplate, perform the following steps:
1. Press the darker metal button on the right side of the faceplate
and keep it pressed.
2. When standing right in front of the SpycerBox Cell, pull the face-
plate with moderate but intense strength from the right side to
your direction.
3. Take the faceplate out of its fastening on the left side.
Then you can access the hard disks of the hard disk tray (see section
“Hard Disk Tray” on page 2-6).
Fastening the faceplate
After finishing your task at hand you have to fasten the faceplate to the
R&S DVS system again. For this perform the following:
1. Simply put the faceplate back into its fastening at the left side.
2. Press the faceplate with moderate but intense strength until it
snaps into its fastening at the right side.
With this the task of fastening the faceplate is finished and the R&S
DVS logo in the middle of the faceplate will be illuminated again.
1
2

Overview
Overview of the Front
2-6
SpycerBox Cell | Hardware Guide | Version 1.0
Rohde & Schwarz DVS GmbH
2.2.2 Hard Disk Tray
The hard disk tray contains the hard disks and is the main storage of the
R&S system. To prevent data loss in case a hard disk fails, it is RAID pro-
tected.
Once the faceplate is removed (see section “Faceplate” on page 2-4),
you have access to the hard disk trays:
Figure 2-3: Hard disk tray
Each hard disk of the array is connected to the system with the help of
a disk carrier which makes the removal of a hard disk from the system
easy.
Further information about RAID can be found in section “Introduction to
RAID” on page 5-2.
Pulling out two trays at the same time
When pulling out two trays at the same time, there might be an
overweight at the front of the system and a risk of damaging it.
Pull out one tray only and slide it back in the system before
pulling out the second tray.
hard disk
hard disk tray