Ranger design 5069-2 User manual

INSTALLATION GUIDE
5069-2 Drawer Cabinet
( aluminum )

QUICK START GUIDE
REQUIRED ITEMS
2
PERSONS
q1.1 Setup............................................................................................................................................... 3 - 4
Phase 1 - Assembly
Phase 2 - Installation
5 - 6
7 - 8
qCordless Drill
qCordless Impact
qRivet Gun
qTape Measure
qMarker
q7/16" Socket
q3/8" Drill Bit
q7/32" Drill Bit
q3/8" Driver Bit
qKnife
q2.1 5069-2 Shelving Installation...........................................................................................................
q2.2 5069-2 Floor or Flat Surface Installation........................................................................................

For technical support, contact us at 1-800-565-5321 5069-2 Installation Guide |REV. C1 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.1 Unpack components; compare with the bill of materials.
1.1.2 Verify all parts are present.
Item No. Description Qty.
56-184 Mounting Bar 2
5069-2 Drawer Cabinet 1
90-5037 Fastener Kit 1
BILL OF MATERIALS
5069-256-184 56-184

For technical support, contact us at 1-800-565-5321 5069-2 Installation Guide |REV. C1 | Page 4
90 - 5037 Fastener Kit Fastener Assembly
1.1.3 Fastener kits.
8× # 96-202 Closed End Blind Rivet
3/16" × 1/4"
4× # 92-100
Screw HWH
#14 × 3/4"
ZINC
8×
#96-202 Closed End Blind Rivet
4×
#92-100 Screw #14 × 3/4"
4× # 98-112
Flat Washer
1/4"
ZINC
4× Plusnut
# 94-130
4× # 98-118
Lock Washer
1/4"
ZINC
8×
Spacer
0.375" ID, × 1.0" OD × 0.25" LONG
NYLON
# 98-157
4×
Hex Bolt
1/4"-20 × 2"
GR-5 ZINC
# 90-130
4×
#90-130 Hex Bolt 2"
#98-118 Lock Washer
#98-112 Flat Washer
#98-157 Flat Spacer
#94-130 Plusnut
For Shelving Install
For Floor or Flat surface Install

For technical support, contact us at 1-800-565-5321 5069-2 Installation Guide |REV. C1 | Page 5
2.2.1 • Place the mounting bar to the drawer cabinet as shown, then mark the holes of the
drawer cabinet to the mounting bars.
• Drill the marks on the mounting bars.
2.2.2 Attach the mounting bars to the drawer cabinet.
PHASE 2 – INSTALLATION
2.1 5069-2 SHELVING INSTALLATION
TOOLS
qCordless Drill
qMarker
q7/32" Drill bit
TOOLS
qRivet Gun
HARDWARE USED
8×
#96-202 Closed End Blind Rivet
Mark Mark Drill the mark Drill the mark
1 - 3/16"
3 - 5/8"

For technical support, contact us at 1-800-565-5321 5069-2 Installation Guide |REV. C1 | Page 6
2.2.3 • Place the darwer cabinet to the shelving tray, you need 15" space between 2 shelf trays.
• Screw the mounting bars to the shelf extrusion.
NOTE: If the shelf tray is 14" or deeper attach 2 dividers on the tray, under the drawer cabinet.
NOTE: Drill holes in the mounting bar 1st before putting the screws.
15"
Dividers for 14"or deeper shelf tray
TOOLS
qCordless Drill & Impact
qMarker
q7/32" Drill bit
q3/8" Driver Bit
#92-100 Screw #14 × 3/4"
HARDWARE USED
4×

For technical support, contact us at 1-800-565-5321 5069-2 Installation Guide |REV. C1 | Page 7
2.2.1 •Place the drawer cabinet in the oor or at surface.
• Remove the 2 drawers.
2.2.2 •Marks the 2 holes on the drawer cabinet.
• Drill the marks, then attach plusnuts to the holes.
PHASE 2 – INSTALLATION
2.2 5069-2 FLOOR or FLAT SURFACE INSTALLATION
Remove
Left Slider - Pull up to remove
Right Slider - Push down to remove
Mark Mark
TOOLS
qCordless Drill
qMarker
q3/8" Drill bit
HARDWARE USED
4×
#94-130 Plus Nut .250

For technical support, contact us at 1-800-565-5321 5069-2 Installation Guide |REV. C1 | Page 8
2.2.3 •Attach the drawer cabinet to the oor or at surface.
• After attaching the drawer cabinet slide the drawer back.
Slide the drawer back
#90-130 Hex Bolt 2"
#98-118 Lock Washer
#98-112 Flat Washer
#98-157 Flat Spacer
#94-130 Plusnut
HARDWARE USED
4×
TOOLS
qCordless Impact
q7/16" Socket

For technical support, contact us at 1-800-565-5321 5069-2 Installation Guide |REV. C1 | Page 9
“You have successfully installed your
5069-2
Thank you for doing business with us.”
For any feedback or suggestions you may have, please contact: [e-mail]