Ranger 5060-5 User manual

INSTALLATION GUIDE
5060-5 Drawer Cabinet
5 Drawers ( Aluminum )

QUICK START GUIDE
REQUIRED ITEMS
2
PERSONS
q1.1 Setup...............................................................................................................................................
q1.2 Drawer Cabinet Assembly...............................................................................................................
3 - 4
5
Phase 1 - Assembly
Phase 2 - Installation
qCordless Impact
qCordless Drill
qTape Measure
qMarker
q1/2" Socket
q3/8" Drill Bit
q7/16" Socket
q1" Hole Saw
qKnife
qPlus Nut Tool
q2.1 Drawer Cabinet Installation.............................................................................................................. 6 - 11

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.1 Unpack components; compare with the bill of materials.
1.1.2 Verify all parts are present.
Item No. Description Qty.
40-441 Mounting Track Installation Bracket 2
5060-5 Drawer Cabinet 1
94-8001 Assembly Fastener Kit 1
96-5003 Install Fastener Kit 1
BILL OF MATERIALS
5060-5
40-44140-441

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 4
94-8001 Fastener Kit Fastener Assembly
1.1.3 Fastener kits.
Fastener Assembly96-5003 Fastener Kit
4×
Hex Bolt
5/16"-18 × 3/4"
GR-5 ZINC
# 90-204
# 98-116
4×
# 94-116
Serrated Nut
5/16"-18
ZINC
4×
2×
Hex Bolt
5/16"-18 × 1"
GR-5 ZINC
# 90-208
10× # 90-130
Hex Bolt
1/4"-20 × 2"
GR-5 ZINC
12× # 98-112
Flat Washer
1/4", O.D 3/4"
ZINC
2× # 98-116
Flat Washer
5/16" - 18
ZINC
12× Plusnut .250
# 94-130
12× # 98-118
Lock Washer
Regular 1/4"
ZINC
2× # 98-122
Lock Washer
5/16"
ZINC
30×
Spacer
0.375" ID, × 1.0" OD × 0.25" LONG
NYLON
# 98-157
# 90-114
Hex Bolt
1/4"-20 × 1"
GR-5 ZINC
2×
2× # 94-150 Channel Nut w/ Spring
5/16"
10×
#90-130 Hex Bolt 1/4" × 2"
#98-118 Lock Washer
#98-112 Flat Washer
#98-157 Spacers
( QTY = Gap beTween floor and end panel )
#94-130 Plus nut
2×
#90-114 Hex Bolt 1/4" × 1"
#98-118 Lock Washer
#98-112 Flat Washer
#94-130 Plus nut
#90-208 Hex Bolt 5/16" × 1"
#98-122 Lock Washer
#98-116 Flat Washer
#94-150 Channel Nut
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#94-116 Serrated Nut
4× ( for mounting kits only )
Flat Washer
5/16" × 18
ZINC
2× ( for mounting kits only )

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 5
1.2.1 • Remove all the PVC from all the parts.
• If you have mounting kits attach the mounting track installation brackets.
PHASE 1 – ASSEMBLY
1.2 DRAWER CABINET ASSEMBLY
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#94-116 Serrated Nut
HARDWARE USED
4× hand-tighten the bolts
40-441
5060-5
40-441
NOTE: Don’t do this step if you don’t
have mounting kits or
mounting track.

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 6
PHASE 2 – INSTALLATION
2.1 DRAWER CABINET INSTALLATION
G717
2.1.1 Sample vihecle package picture with 5060-5 drawer cabinet.
5060-5

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 7
2.1.2 Remove all the drawers by pushing down or pulling up the black pin on the sliders.
Left Slider - Pull up to remove
Right Slider - Push down to remove
Remove the 5 drawers.

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 8
5060-5 SHELVING
Put the drawer cabinet in place.
NOTE: Always start install from front of the vehicle to rear.
NOTE: The position of the drawer cabinet
depends on your package.
2.1.3 Lift the drawer cabinet inside the van, then put it in place.

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 9
2.1.4 Mark the ten bottom holes on the vehicle oor and the two back holes on the horizontal rim.
TOOLS
qMarker
NOTE: Mark the two holes on the
rear panel that line up with
the horizontal rail of the
vehicle, and if you don't have
a mounting kit with a oor
track, mark the ten bottom
holes on the oor.

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 10
2.1.5 • Lift the drawer cabinet on the side.
• Drill all the marks using 3/8" drill bit, then attach plus nuts to the holes.
Attach plus nuts to the holes.
HARDWARE USED
12×
#94-130 Plus Nut .250
TOOLS
qPlus Nut Tool
Drill all the marks using 3/8" drill bit.
TOOLS
qCordless Drill
q3/8" Drill Bit
q1" Hole Saw
NOTE: Before drilling, ensure that you will not hit any critical parts of the vehicle like the Gas tank,
Wiring Harness and Hose.
NOTE: If the vehicle has wood or rubber oor,
drill the oor using 1" hole saw, then
drill the vehicle oor using 3/8" drill bit.

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 11
2.1.6 Install the drawer cabinet to the van, then slide the drawers back to the drawers cabinet.
After installing the drawer
cabinet, slide the drawers
back.
NOTE: The number of spacers depends on the gap between the oor and end panel.
#90-130 Hex Bolt 1/4" × 2"
#98-118 Lock Washer
#98-112 Flat Washer
#98-157 Spacers
#94-130 Plusnut ( Already Installed )
HARDWARE USED
10×
TOOLS
qCordless Impact
q7/16" Socket
#90-114 Hex Bolt 1/4" × 1"
#98-118 Lock Washer
#98-112 Flat Washer
#94-130 Plusnut ( Already Installed )
HARDWARE USED
2×
TOOLS
qCordless Impact
q7/16" Socket
NOTE: After installing the locker make sure that all bolts are tightened.

For technical support, contact us at 1-800-565-5321 5060-5 Installation Guide |REV. E1 | Page 12
“You have successfully installed your
5060-5 Drawer Cabinet
Thank you for doing business with us.”
For any feedback or suggestions you may have, please contact: [e-mail]