PAGE
GOTO
CLEAR
ENTER
MOB
TOPSHAM
EXETER
TEIGNMOUTH
EXMOUTH
TORQUAY
DARTMOUTH
PLYMOUTH
ENPORT
SALCOMBE
PORTLAND
HARBOUR
ISLE O
CAP DE
LA HAGUE
ALDERNEY
GUERNSEY
JERSEY PORTB
CSR 48°30.367'N
POS °35.636'W
128 nm
FIND SHIP ROUTES WAYPOINTS
BRG 23 °T
RNG 40.9 nm
86051_1A
Quick Reference Card - RayChart 420/420D Chartplotter
PAGE - Selects Setup options and display mode.
Press to display Setup Function Bar and use horizontal trackpad
movements to highlight required option. Press ENTER to select
Press PAGE again repeatedly to cycle through display modes
POWER
Press and hold until unit beeps to turn on display
Press once to adjust lighting & contrast.
Press and hold for 3 seconds to turn off display
Function Bar
Press ENTER to display primary Function Bar (as shown here)
Use trackpad to highlight function then ENTER to select
Elipses (...) after the text indicate further options available
by highlighting then pressing ENTER
ENTER
Confirms selection and (if appropriate) clears current
functions. It either performs the selected task and
accepts changes, or confirms selection of more options
GOTO WAYPOINT
Press GOTO to display Function Bar
Select GOTO WAYPOINT function to display Waypoint List
Trackpad
Controls cursor position on screen and highlights functions
RANGE
Adjusts chart scale
Displayed vertical distances shown in Status Bar (top of screen)
- Press top of key to increase the chart range
- Press bottom of key to decrease the chart range
- Press and hold to change the scale rapidly
CLEAR
Cancels operation in progress and returns to previous display
Deletes a highlighted item
WAYPOINT LIST
SYMBOL NAME
WAYPOINT 00
WAYPOINT 002
WAYPOINT 003
WAYPOINT 004
WAYPOINT 005
50°2 ,966'N
00 °20,368'W
POSITION
BRG _186°T RNG _21.0NM
DATE ---- TIME --:--
GOTO
WAYPOINT
TRACKPAD SELECTS WPT, "ENTER"
STARTS GOTO, "CLEAR" TO QUIT
Press ENTER to implement GOTO WAYPOINT function
MOVE CURSOR, "ENTER" TO START
GOTO CURSOR, "CLEAR" TO QUIT
GOTO
CURSOR
Use trackpad to highlight required waypoint
GOTO CURSOR
Press GOTO to display Function Bar
Select GOTO CURSOR function
Press ENTER to place a temporary waypoint and start the GOTO
TRACKPAD SELECTS PORT, "ENTER"
STARTS GOTO, "CLEAR" TO QUIT
GOTO
PORT
GOTO PORT
Press GOTO to display Function Bar
Select GOTO PORT function
- The Port List is displayed
Use trackpad to highlight required port
Press ENTER to start the GOTO
STOP
GOTO
To stop a GOTO
Press GOTO to display Function Bar (or move cursor over any
waypoint in the current route)
Select STOP GOTO or STOP FOLLOW (as appropriate)
Press ENTER to stop the GOTO
- The dotted line from your vessel to the target disappears
STOP
FOLLOW
SYSTEM SET UP
Use horizontal trackpad movements to highlight SYSTEM SET UP
Press ENTER to select
or
Use vertical trackpad movements to select parameter
Use horizontal trackpad movements to change setting
Press ENTER to implement change
SYSTEM
SET UP
CHART
SET UP
TRACK
SET UP SET UP
GPS
CHART SET UP
Use horizontal trackpad movements to highlight CHART SET UP
Press ENTER to select
Use vertical trackpad movements to select parameter
Use horizontal trackpad movements to change setting
Press ENTER to implement change
SYSTEM
SET UP
CHART
SET UP
TRACK
SET UP SET UP
GPS
TRACK SET UP
Use horizontal trackpad movements to highlight TRACK SET UP
Press ENTER to select
Use horizontal trackpad movements to select INTERVAL
Use vertical trackpad movements to change setting
Press ENTER to save value
Use horizontal trackpad movements to highlight TRACK OFF
Press ENTER to start track - text indicates TRACK ON
SYSTEM
SET UP
CHART
SET UP
TRACK
SET UP SET UP
GPS
GPS SET UP and Status
Use horizontal trackpad movements to highlight GPS SET UP
Press ENTER to display the GPS Status page
Press ENTER to display the Differential GPS Set Up page (RC420D)
Use vertical trackpad movements to select parameter
Use horizontal trackpad movements to change setting
Press ENTER to implement change
SYSTEM
SET UP
CHART
SET UP
TRACK
SET UP SET UP
GPS
SMARTROUTE
To convert a track to a route, select MAKE INTO ROUTE
Press ENTER to convert to a (reversed) route
Man OverBoard (MOB)
Press and hold GOTO for at least two seconds
- Waypoint 0999 is created and marked with MOB symbol
- Status Bar shows bearing and range to the MOB position,
elapsed time since initiated and Course Over Ground data
86051_1.p65 09/11/99, 10:451
