Raynor 540RGD User manual

OPENER
WALL
PUSH
BUTTON
TRANS
PRIMARY
24v
1
2
3
Universal Radio
Control (Top)
Common
Push Button
Radio Pwr.
#3 Connection
(optional)
TM
This unit is specifically designed to operate with Raynor
residential garage door openers. Use on other types may
result in damage to the receiver.
NOTE: Models 540-1RGD and 540-2RGD are factory
pre-set with matching receiver and remote control
codes. If you purchase additional remote controls,
the receiver may be programmed to match the new
remote control code (up to 4 “smart” remotes and
one Keyless Entry Transmitter).
THE RECEIVER MAY BE INSTALLED IN ONE OF TWO
WAYS:
1. Mounted directly on the door opener with clips
provided as shown on page one.
2. Attached to an inside wall of the garage with connecting
bell wire (not supplied) as shown on side two.
When installing two or more receivers in a garage,
position them at least 10 feet apart to prevent electronic
interference.
MOUNTING ON RESIDENTIAL OPENERS
Use a 3 wire connection only. Attach mounting clips to
receiver terminals 1, 2, and 3, and to the opener
terminals used for push button controls (Figure 1).
MOUNTING ON GARAGE WALL
Fully extend the antenna wire below bottom of case.
Fasten the receiver to an inside garage wall with dry wall
screws provided. A convenient place is alongside the
service door and
OUT OF THE REACH OF CHILDREN.
Attach one end of 3-strand bell wire (not supplied) to
receiver terminals 1, 2 and 3. Connect the other end to
the three opener terminals used for push button controls
and radio power (Figure 2). Use insulated staples to
secure bell wire between receiver and opener.
Reconnect power to the opener. The receiver push bar
should light.
Model 540RGD
Receiver Only Model 540-1RGD (With 1 Remote Control) Model 540-2RGD (With 2 Remote Controls)
Side two contains code setting instructions and
service information.
Children operating or playing with a garage door
opener can injure themselves and others.
The
garage door could close and cause serious injury
or death.
Do not allow children to operate the
push buttons or the remote control transmitters.
Install the receiver (and any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but
where the garage door is visible.
A moving garage door could injure someone
under it.
Activate the opener only when the door
is properly adjusted, you can see it clearly, and
there are no obstructions to door travel.
WARNING
Disconnect power to the garage door opener
before installing the receiver.
G
WARNING
OPENER
TERMINALS
Receiver
Terminals
Antenna Wire Fully Extended
Flange
Mounting
Clip #1
Mounting
Clip #2
Mounting
Clip #3
Common
Push Button
Radio Power
To comply with FCC/IC rules, adjustment or modification of receiver and/or
transmitter is prohibited, except for changing the code setting and replacing
the transmitter battery. THERE ARE NO USER SERVICEABLE PARTS.
NOTICE TO U. S. CONSUMERS:
Some states prohibit the service or repair of garage door
openers whch cannot be made to comply with the safety
standards contained in UL 325 (1988 revision). In order to
comply with both the letter and the spirit of these laws, this
universal radio control should not be used with any Raynor, Lift-
Master®, Chamberlain®, or Sears Craftsman®garage door opener
manufactured prior to April 1, 1982. To find out if your
Chamberlain-made garage door opener was manufactured prior
to or after April 1, 1982, please call 1-800-528-9131 before
installing this universal radio control.
Figure 1
Mounting on
Opener
Figure 2
Mounting on Wall
1
GARAGE DOORS
Universal Radio Control
OWNERS MANUAL

THE REMOTE CONTROL TRANSMITTER
The portable remote may be secured to a car sun visor
with the clip provided. Additional remote controls can be
purchased at any time for all vehicles using the garage.
If the battery has sufficient power, the light will glow and
the opener will operate when the remote push button is
pressed.
The 12 Volt battery should produce power for at least a
year. When the light is dim or doesn't come on, replace
the battery. If the transmission range lessens, check the
battery light.
TO CHANGE THE BATTERY: Slide the battery
compartment cover down. Remove original battery and
position new battery as directed.
KEY NO. PART NO. DESCRIPTION KEY NO. PART NO. DESCRIPTION
1 41A4504-1 Remote Control case (housing 4 540RGD Universal Receiver
only; circuit board not included) Not Shown
2 10A14 12V Battery Model 81RGD Extra Remote Control
3 29C128 Visor clip (Complete)
13
2
4
321
© 1995, The Chamberlain Group, Inc.
114A1687E All Rights Reserved Printed in Mexico
SET RECEIVER
TO MATCH REMOTE CONTROL(S) CODE
Pry open the front panel of receiver case with a coin or a
screwdriver.
1. Press and
hold the remote control push button.
2. Then press and release the "Smart" button on the
receiver. The adjacent indicator light will
flash once.
3. Release the remote control push button.
The opener will now operate when the push button on
either the receiver or the remote control is pressed.
Repeat Steps 1 -3 for each remote control that will be
used to operate the garage door opener.
NOTE: If the remote control push button is not held
down until the receiver indicator light flashes, the
receiver will not learn the code.
TO ERASE ALL REMOTE CONTROL CODES
• Press and hold the "Smart" code button on the
receiver panel until the indicator light turns off (about
6 seconds).
All the codes the receiver has learned
will be erased.
• Repeat Steps 1-3 to reprogram the receiver for each
remote control transmitter in use.
3
2
1
UNIVERSAL RECEIVER
Remote Control Transmitter
Push Button
Smart
Button
Indicator Light
UNIVERSAL RECEIVER
REPLACEMENT PARTS