RC Lander T-33 Quick start guide

RCLander T-33
OPERATIONAL MANUAL

- 2 -
Please read before operating this system!
W
e would like thank you for purchasing our new product T-33,
designed for the hobby enthusiast. Based on its full - scale
counterpart, this USA Jet can undertake loops, inverted flight, rolls
and other aerobatics easily. It is a highly maneuverable model aimed
at the intermediate to expert pilot. With the T-33 model which
includes EDF set*, speed controller, electric servo, flaps, metal
electric retractable landing gear & scale suspension struts with front
steering, full scale functional g ar doors system & air-brake system.
You will have joyful time in model flying.
Remarks:*
We have metal EDF set for your selection.
1) LEDFDPS90-1A13 is a higher grade EDF set which is an
aluminum alloy material EDF offering a powerful output without
compromising efficiency and durability.
2) Please be aware that although all servos have been pre-set to the
center point at our factory there may be discrepancies due to
different radio manufacturers . Please make sure that you check
the centre point with your own radio before installing of the model.
4) Centre of Gravity for this model is measured 120mm (+ 5mm)
from main wing leading edge to centre direction.
5) Please make sure to use a little piece of velco or strong foam
double tape (not included) to secure your LiPo battery before
flying.

- 3 -
Specifications:
Wing Span :
1683mm
Length:
1520mm
AUW:
3.7kg up
EDF(Lander Metal DPS EDF):
90mm
Power:
9S 4500mAh 25C or above
Thrust:
Up to 3.96kg
Function:
Flaps system-included
Metal Electric retract & scale suspension struts included
Gear doors system & Air-Brake (Option)
ESC:
100A or above
EDF SYSTEM
L
LL
LEDF
EDFEDF
EDFDPS
DPSDPS
DPS90
9090
90-
--
-1A
1A1A
1A13/9
13/913/9
13/9
Material: Aluminum Alloy, Metal special
Weight: Ca. 538g(Motor included)
Rotor: 90mm dia, 5-bladed.
Max rpm 42,000 rpm
Application: 2508W
Staic Thrust: 3.96kg
Main Accessories

- 4 -
Main Fuselage Front Lower Fuselage Both side of Inlet Parts
Inside Ducting plate Parts Upper Rear Fuselage Lower Rear Fuselage
Both Side Main Wing Set Horizontal Stabilizer Vertical Stabilizer
Canopy 90 & 120 EDF Bay Parts Both Side Fuel Tanks

- 5 -
Bombs& Missiles Parts PVC Wheel Cups parts PVC Gear Doors Parts
PVC Air-Brake Set Plywood Block Set
Remarks: 1) Operational Manual (included)
2) Extension cord x 7pcs & Y cord x 6pcs (included) except ARF version
3) Push rods for Elevator, Rudder, Aileron, Flaps, Air-Brake & Front Steering (included)
5) One plastic bag includes screws, Control Horns, Linkage Stoppers & related plywood block
set.

- 6 -
Assembling the aircraft.
For color images please go to www.rclander.com for
download.
01
1) Take one extension cord to connect the
nose electric retract first.
2) The nose electric retract has been
pre-installed by factory before
shipment.
02
1）Suggest to find one piece 70-130mm
anti-slip foam plate (not included) for the
battery compartment.
03
1) Using the strong double tape to fit on the
anti-slip foam plate on the battery
compartment as shown. Then put on the
nose gear extension cord well.
.

- 7 -
04
1) Use your Radio to gear down the nose
gear first for preparation to glue up the front
lower fuselage on the main fuselage.
05
1) Take enough epoxy to glue up the lower
front fuselage on the main fuselage.
06
1) After finished the fixing of lower front
fuselage, keep on the install the inside
ducting plate.
2) Pls glue up the both side ducting plates
together first.

- 8 -
07
1)According to the inside slot of main
fuselage to take some epoxy to glue up the
inside ducting plate set on the right position.
08
1) After glued up the inside ducting plate,
pls cut out the cross foam bar as shown.
09
1) Prepare to install both side inlet parts on
the main fuselage

- 9 -
10
1) Inside the main fuselage is already pre
set some slot for fitting both of two side
inlet parts.
2) Kindly use the enough the epoxy and
work carefully to install the inlet parts
one by one as shown. It is because glue
up area so longer.
11
1) Glue up both side inlet parts on the main
fuselage should be one by one procedure.
12
1)Install the both side guiding inlet air plates

- 10 -
13
1) Make sure the guiding inlet plate to be
able fitted on the right position before
glue up. Pls be reminded the shorter
side is out & longer side is in side.
2) The installing method is put it from
inside to outside.
14
1) After confirm the guiding inlet plate on
the right position that can be used some
epoxy to glue up as shown.
15
1) Prepare to install the horizontal &
vertical stabilizer on the upper rear main
fuselage.
2) Pls install the related servos before glue
up action.

- 11 -
16
1) Pls use the cutter to open a small hole on
the slot of the horizontal stabilizer for pass
through rudder servo cable.
17
1) Pre-check the vertical stabilizer to be
able well on the horizontal stabilizer slot
before glue up action.
18
1) Use some epoxy to glue up the vertical
stabilizer on the horizontal stabilizer. Pls
make sure it able on the vertical degree.

- 12 -
19
1) Pre-check the whole set stabilizer can be
well on the upper rear main fuselage and
the rudder servo cable well pass through
before glue up action.
20
1) Everything is correct then takes some
epoxy to glue up as shown.
21
1) Prepare to install the main wing. Pls be
noted the retract plug gear doors
system and air-brake system are
pre-installed by factory before
shipment.
2) Pls prepare the related servos /
extension cables and related pre-cut
wood plates (included with the kit).

- 13 -
22
1) Gear down both side main gear first.
2) Glue up on side pre-cut wooden plate
(shorter one) on one side maid wing
(bottom) slot as shown.
23
1) Take enough epoxy to glue up both side
main wings together.
2) Recommend to take some epoxy to
fit up the gap or at lease on the upper
of both of wooden plates for
reinforcement purpose.
24
1) After finished the bottom side, turn
around to install the upper side
reinforcement wooden plated (included
with the kit) on the middle main wing
slots as shown.
2) Take some epoxy to fit up the gap or
at least on the upper position of both
of wooden plates for reinforcement
purpose.

- 14 -
25
1) Install the Aileron & Flaps servos on the
main wing servos bay and use the
extension cables to extend the cable
pass through into the main fuselage.
2) Pls be reminded that the joiner
position of extension must be fully
put into the cable slot by cut out
some foam for gaining the space if
necessary.
26
1) All related servos cables included of
Aileron/ Flaps and metal retract gear cable
must be passed through under the metal
retract to main fuselage.
27
1) Prepare install the main wing front edge
bind nut wooden plate on the main
fuselage.

- 15 -
28
1) Pre check the related wooden plate to be
able on the right position or not before glue
up.
29
1) Take some epoxy to glue up the wooden
plate on the main fuselage as shown.
30
1) Take some epoxy or hot melt glue to fit
on the steering servo on the main fuselage
and link up the related push rod as shown.

- 16 -
31
1) Prepare to install the upper rear fuselage
to the main fuselage. Pls be reminded to
check up the four reinforcement carbon
tube able connect the right position on
the main fuselage and make sue whole
set stabilizer on the right angle before
glue up.
32
1) Take enough epoxy to glue the upper
rear fuselage on the main fuselage.
33
1) After glued up action, take one y & one
extension cable to link up both side elevator
servos and one more extension cable for
rudder servo. Then use some hot melt glue
to fix on the cable on the right position as
shown.

- 17 -
34
1) Make sure the related extension cable on
the right position then prepare to install the
lower rear fuselage on the main fuselage.
35
1) Use some epoxy to glue up the lower
rear fuselage on the main fuselage. Pls be
reminded that the main rear edge wing bind
nut wooden plate was pre-installed by
factory.
36
1) Put in the pvc exhaust tube (included
with the kit) on the EDF set as shown.

- 18 -
37
1) Take the metal edf mount (included with
the kit) to lock up the EDF set on the
bay and lock up the ESC on the wooden
plate as shown.
2) Pls be reminded to check the EDF
set space is fully enough installed
your EDF set (specially other brand
name edf set). Otherwise, you need
to cut out some foam to gain the
space or add some strong foam tape
to fill up the gap before locked up by
the metal mount.
38
1) Put on the foam edf cover with some
double tape for fixing.
2) Pls make sure the both side edge of
cover should be on the same level as
the fuselage. Otherwise, you need to
cut out some foam on the cover for
gaining more space or add some
foam in order to meet the above
requirement.
39
1) Install the elevator control horn and link
up the push rod with servo.

- 19 -
40
1) Install the other side elevator & rudder
control horns and link up the push rods with
servos.
41
1) Install both side main wings control horns
of Aileron & flaps and link up the push rods
with servos. Then cover the related servos
by provided pvc pre-painted servos sheet.
42
1) Use the enough Y cables and extension
cables to connect the aileron / flaps &
air-brake servos and well bind up all cables
then fix on the middle position in order to
pass through main fuselage RX
compartment easily.

- 20 -
43
1) Pass through all related cables from
main wing into the main fuselage RX
compartment before lock up the main wing
on the fuselage.
44
1) Use the provided 4mm screws &
wooded plates and washers to lock up
the main wing on the fuselage as
shown.
2) 4 x 40mm for front & rear position. 4 x
35mm for middle position.
45
1) Prepare to install both side fuel tanks
parts /bombs & missiles.