RDA FirePro V2 User manual

Manual (Translated)
FirePro V2 Control Unit
Door control for FS drives:
EN
FirePro V2 Control
Hardware version V2. 3
Software version V4.1
Publication Date: 02/12/2021

Door control
FireProV2
Manual
Please keep this manual with attachments carefully!
1

Door control
FireProV2
Manual
Please keep this manual with attachments carefully!
2
1 Index:
1Index:.............................................................................................................................2
2Safety instructions.........................................................................................................4
2.1 Relevant Safety requirements:...............................................................................4
3Control Print Overview.................................................................................................5
4Schedule with NES motor.............................................................................................6
5Schedule with DES motor.............................................................................................7
6Technical data ...............................................................................................................8
7Description of Control Unit...........................................................................................9
7.1 Fire alarm:..............................................................................................................9
7.2 Smoke detection:....................................................................................................9
7.3 Siren/Alarm:...........................................................................................................9
7.4 Safety edge:............................................................................................................9
7.5 Photocell protection:............................................................................................10
7.6 Light curtain:........................................................................................................10
7.7 Escape button:......................................................................................................10
7.8 Maintenance Cycle: .............................................................................................10
8Mounting.....................................................................................................................11
9Connect........................................................................................................................12
9.1 Power supply:.......................................................................................................12
9.2 Power supply 24 VDC / Battery Charger: ...........................................................13
9.3 Motor: ..................................................................................................................14
9.4 Mechanical End Switches:...................................................................................14
9.5 Digital limit switches:..........................................................................................15
9.6 Roll-off, cable break/slack cable protection: .......................................................15
9.7 UP-Stop-down operation: ....................................................................................16
9.8 Photocell: .............................................................................................................16
9.9 Light curtain:........................................................................................................16
9.10 Connecting LIGI 01-PNP light curtain: ...........................................................17
9.11 Connecting LIGI 01-PNP light curtain: ...........................................................19
9.12 Key switch:.......................................................................................................21
9.13 Fire Alarm / Smoke detector:...........................................................................21
9.14 Escape button: ..................................................................................................21
9.15 Impulse:............................................................................................................21
9.16 Safety edge:......................................................................................................22
9.17 Siren/Alarm:.....................................................................................................22
9.18 Outputs:............................................................................................................23
9.19 Smoke detection (only in combination with inflatable bellows):.....................23
10 Setting control..........................................................................................................25
10.1 Adjust limit switches NES ...............................................................................25
10.2 Adjust limit Switches .......................................................................................25
10.3 Automatic or hold to run operation..................................................................26
10.4 Duration NES Motor........................................................................................26
10.5 Protections........................................................................................................27
10.6 Impulse function...............................................................................................27
10.7 BM (Fire alarm) function.................................................................................28
10.8 RM (Smoke detection) with Reset function.....................................................28

Door control
FireProV2
Manual
Please keep this manual with attachments carefully!
3
10.9 Continuing when empty or disconnected battery:............................................29
10.10 Opening after passing digital limit switches ....................................................29
10.11 Low battery voltage..........................................................................................29
10.12 Notifications.....................................................................................................29
10.13 Maintenance counter ........................................................................................30
11 Menu........................................................................................................................31
11.1 Parameter settings 0. : ......................................................................................31
11.2 Parameter settings 1. : ......................................................................................33
11.3 Parameter settings 2. : ......................................................................................34
11.4 Parameter settings 3. : ......................................................................................35
11.5 Parameter settings 4. : ......................................................................................36
11.6 Parameter settings 5. : ......................................................................................37
11.7 Parameter settings 8. : ......................................................................................37
11.8 Parameter settings 9. : ......................................................................................37
12 Notifications ............................................................................................................38
12.1 E; Status notifications : ....................................................................................38
12.2 F; Error messages:............................................................................................39
12.3 Common Errors................................................................................................42
13 Declaration of Conformity.......................................................................................43

Door control
FireProV2
Manual
Please keep this manual with attachments carefully!
4
2 Safety instructions
This manual is translated from the original Dutch manual, In the event of discrepancies between
the two, the Dutch version shall prevail.
Read this manual carefully before starting work on this
Control unit. Check the screw connections before this control unit becomes operational.
Caution: before starting work on this control, first
Disconnected the power supply and disconnect the poles of the batteries.
Performing work on this control under tension is life-threatening & can cause serious
injuries!
Only qualified personnel with appropriate equipment and knowledge are permitted to carry
out work on this control. Qualified personnel means persons who are familiar with the
installation, configuration, commissioning & operation of electrically driven door, gate
installations. They must be able to assess the complete installation, identify possible
hazards and apply the necessary safeguards.
2.1 Relevant Safety requirements:
The safe use of this control can only be guaranteed when used as intended. The manufacturer is
not responsible for damage that has occurred due to external components or non-compliance with
these instructions.
Modifications are only permitted in accordance with the manufacturer. If modifications are applied
without the manufacturer's consent, the manufacturer's declaration is not valid.
During installation, commissioning, maintenance and control of the controller shall
Specific case applicable in compliance with the safety and accident prevention rules
to be taken.
Only apply safety products (as: safety edges and photocells which comply with applicable
standards.)
The manufacturer accepts no liability for damage resulting from operating and connection errors,
neglect of the operating instructions or inadequate maintenance and / or service, and again refers to
the possible occurrence of dangerous situations.
Despite conformity with harmonized standards, not every possible hazard can be foreseen. For this
reason, people should only enter the danger zone if this is necessary.
If in doubt about the installation, do not proceed and contact the
Technical Service for clarifications.
All information on this document (photos, drawings, characteristics and dimensions) may be
subject to change without prior notice.
Please read this manual carefully and keep this manual with
Attachments carefully!

Door control
FireProV2
Manual
Please keep this manual with attachments carefully!
5
3 Control Print Overview

Door control
FireProV2
Manual
Please keep this manual with attachments carefully!
6
4 Schedule with NES motor

Door control
FireProV2
Manual
Please keep this manual with attachments carefully!
7
5 Schedule with DES motor

Door control
FireProV2
Manual
Please keep this manual with attachments carefully!
8
6 Technical data
Power supply : 3N ~ 400VAC +/-10%, 50/60Hz
: 3 ~ 230VAC +/- 10%, 50/60Hz
: 1N ~ 230VAC +/-10%, 50/60Hz
Fuse : Max. 5A Slow
Maximum power : 2,2Kw
Maximum current : 8,5A
Control voltage : 24Vdc
Control current : 300mA
External power supply : 24Vdc
Maximum current : 100mA
Battery : Voltage: 12v
LxWxH: 151x51x94mm
Brand: CSB Battery
Type: UPS123607
Weight: 1.97 kg
Technology: AGM
Relay outputs : Potential-free switch contacts
Maximum load : 230VAC resistive last = 1A/inductive charge = 1A
Relay outputs : Various notifications as N.O. contact with 1 common
Maximum load : 24VDC resistive last =1A / inductive charge =1A
Temperature range : + 5... + 40 °C
Humidity : Max. 93% (non-condensing)
Vibration : Vibration-free mounting (e.g. concrete wall)
Enclosure Size : 400 x 300 x 150mm (L x W x H)
Protection class : IP33
Weight : 9,8kg

Door control
FireProV2
Manual
Please keep this manual with attachments carefully!
9
7 Description of Control Unit
The FirePro is a controller for failsafe drives (FS series) with mechanically adjustable limit
switches (NES) or digital Absolute Encoder (DES) and centrifugal brake. This control unit can
work both automatically and in hold to run. The operation is possible with the control buttons on
the cabinet and by means of external up-stop-down control. There is also an input for an impulse
control (e.g. pull switch) available.
A two-color LED is present on the lid which is green in normal operation and is red in case of
malfunction, fire alarm, smoke detection or power failure. The notification belonging to the red
LED is displayed on the control print display.
There is an input for the safety contact (NC) of the safety brake. If this entry is interrupted, the
door can no longer be operated.
The control unit is equipped with batteries that provide the control voltage and hold the brake in
case of a power failure if there is no fire or smoke notification. In the case of fire alarm, smoke
detection or if the batteries are empty or not present, the door will drops because the power supply
for the brake is gone. When voltage is still present, the door drops until the limit switch is closed
or the "overclose" limit switch is reached. In the menu you can set whether the door is lowered
until the normal limit switch is reached or until the "overclose" limit switch is achieved. With the
"overclose" limit switch a door can possibly drop further than it does during normal operation. A
Stop with a set time can optionally be made at a desired position, during fire alarm, smoke
detection or low battery voltage. This can only be used with CAM switches when the "overclose"
function is not in use.
7.1 Fire alarm:
After fire alarm, the door is released immediately or after extended time (parameter 3.4, 0-140
sec.) .
7.2 Smoke detection:
In the case of smoke detection, a command must be given at the reset entry after the smoke
detection is over. In the case of smoke detection, there is also a potential-free contact indicating
that the door is closed so that the air bellows for smoke sealing can be filled between the door. It
is therefore no longer possible to flee. If this contact is not used for detection, it can be
programmed in the menu to switch if a malfunction is active.
7.3 Siren/Alarm:
When the door is in motion, a potential-free switch can be used to connect a siren or other
signaling. This stops when the door stops moving. in the event of a fire alarm, there is also a
potential-free switch which can also be connected to a siren/alarm or other signaling.
7.4 Safety edge:
It is possible to connect an safety edge. This can be an safety edge by means of DW (air pressure,
1k2) contact, 8k2 safety edge or opto sensors. Under normal operation, the safety edge only works
if automatically Closing is selected. In the event of a fire alarm, smoke detection or low battery
voltage, the safety edge can be switched on or off. If it is switched on, when the safety edge is
activated, the door will stop. The menu allows you to select which safety edge has been chosen
and set the waiting time after the safety edge has been activated before the door continues to drop.
If the power supply is still present, you can also select to fully open the door and then close it
again.