See Water Oil Smart OSS-100 User manual

Your Trusted Source for Quality Control Panels.
®
Oil Smart® Pump Switch & Alarm
Installation and Operation manual
OSS-100
SEE WATER, INC.
Oil Smart® Pump Switch Mounting: NEMA 6P; IP67
Mounting - Mount Oil Smart® Pump Control Sensor with provided
mounting hardware to the pump’s PVC discharge pipe. The ‘OFF’ sensor of
the Oil Smart® Switch shall be positioned at least 3” above the impeller of
the pump.
Oil Smart® Alarm Mounting: NEMA 3R
Mounting - Mount Oil Smart® Alarm panel (OSA-05) to near by wall with
provided
Oil Smart® Plug & Play: 120VAC
The Oil Smart® OSS-100 System incorporates pump controls and alarm
sensors that differentiate between oil and water, allowing companies to
responsibly discharge the water without the risk of pumping oil. Installation of
the OSS-100 keeps companies in compliance with Elevator Code
ASME A17.1 and State/Federal regulations while reducing the risk of adverse
publicity, nes, and expensive cleanup cost.
Model FLA Range
OSS-100 (0.0-16.0 FLA)
www.seewaterinc.com
951.487.8073 • 888.733.9283 • [email protected]
22220 Opportunity Way, Suite 101 • Riverside, CA 92518
Page 1-3 IM 806 REV. 2/19
Remote Monitoring Dry Contacts:
1. Normally Open dry contacts for high oil, high water, and
general high liquid alarm.

Your Trusted Source for Quality Control Panels.
®
SEE WATER, INC.
Sequence of Operation:
Sump Cover
Check Valve
Pump Stop
Pump Start
High Liquid Alarm
Typical Installation of Oil SmartÒ Simplex Control Panel
Oil Smart Ò Alarm OSA-05
Liquid Smart
Ò Alarm Sensor
Oil Smart
Ò Pump Switch
Submersible Pump #1
1
2
3
4
1
4
2
3
Normal Condition (Water Only)
When water comes in contact with the
short (on) sensor, the pump will turn
on. The pump will remain on until
water clears the long (off) sensor.
Oil Present Condition
If oil comes in contact with the (on)
sensor, the pump will not turn on.
Operation of Oil Smart®
Water (Oil Present Condition)
If the water level rises enough to
contact the (on) sensor under the
oil layer, the pump will turn on and
remain on until the (off) sensor clears
WATER
WATER
OIL
LAYER
WATER
OIL
LAYER
WATER
WATER
OIL
LAYER
WATER
OIL
LAYER
Operation of Liquid Smart®
High Water Level
When water comes in contact will both
sensors, the white water indicator on
the front panel will illuminate. This
condition will turn on the red beacon
alarm light and sound the alarm buzzer.
High Oil Level
If oil comes in contact with both sensors,
the yellow oil indicator on the front panel
will illuminate. This condition will turn on
the red beacon alarm light and sound the
alarm buzzer.
Oil Smart® Pump Switch & Alarm
Installation and Operation manual
OSS-100
Testing:
Oil Smart® Pump Switch Testing:
• Place your thumb on the short stainless steel sensor
of the Oil Smart® Pump Switch, and the pump will
turn on. While touching the short ‘ON’ sensor, touch
the long ‘OFF’ sensor with your ngers; remove your
thumb from the short ‘ON’ sensor and begin to move
your ngers down the ‘OFF’ sensor simulating water
being pumped down. Once ngers are removed from
‘OFF’ sensor, the pump will turn off.
• Optional: Fill the sump area with ground water, when
water reaches the ‘ON’ sensor, the pump will turn on
and remain on until water clears the ‘OFF’ sensor.
Liquid Smart® Alarm Testing:
• Submerge both sensors in oil and the yellow oil
indicator on the front panel will illuminate. To test
water sensor, submerge both sensor in ground water
and the white water light will illuminate.
• Both test will illuminate the 360 degree visible beacon
and sound an 85 decibel at 10’ buzzer.
www.seewaterinc.com
951.487.8073 • 888.733.9283 • [email protected]
22220 Opportunity Way, Suite 101 • Riverside, CA 92518
Page 2-3 IM 806 REV. 2/19

Your Trusted Source for Quality Control Panels.
®
SEE WATER, INC.
Notes:
Troubleshooting:
Caution: before checking electrical connections within the control or
attempting to replace any components, turn off all branch circuits supplying
power to the main control panel.
Pump control does not activate the pump or pump does not run
• Verify polarity is correct.
• Conrm all connections are tight and secure.
• White plastic case must be kept clean. Clean with house hold rubbing
alcohol and rag.
• Keep control 1” - 2” clear of any metallic material. Mount to PVC pipe
or if mounted to metal pipe, make sure to mount with See Water quick
mount PVC bracket.
Alarm will NOT activate
• Conrm 120VAC power to circuit board J1-6 and J1-7. Power can be
jumpered from incoming voltage if needed.
• Check for any visual damage to optic or stainless steel sensor on the
Liquid Smart® Sensor.
Preventive Maintenance
• The Oil Smart® Pump Switch and Liquid Smart® Sensor must be kept
clean. If the switches are submerged during install or maintenance,
clean the white plastic case with rubbing alcohol. Consistent inspection
and preventive maintenance ensures longevity and proper operation of
components.
Warranty:
See Water® Inc. warrants that products of its manufacture
are free from defects in material and workmanship for a
period of 5 years from the date of purchase. This date shall be
determined by the date on the invoice and the serial number
on the product.
Replacement of the product is at the discretion of See Water
Inc. This warranty is valid when the product is installed in
compliance with the manufacturer’s installation instructions.
The manufacturer’s obligation under this warranty shall be
limited to the repair or replacement of any parts found by the
manufacturer to be defective, provided that the product is
returned to See Water’s factory, postage prepaid with proof of
original purchase included.
The manufacturer of this warranty shall not be liable under
this warranty if the product has not been properly installed;
any alterations/additions/changes to the product will result in
a void warranty. Failure to properly install and test this prod-
uct can result in personal injury or equipment malfunction.
See Water, Inc. shall not be liable for any loss, damage or
expenses from installation or use of its products.
Oil Smart® Pump Switch & Alarm
Installation and Operation manual
OSS-100
www.seewaterinc.com
951.487.8073 • 888.733.9283 • [email protected]
22220 Opportunity Way, Suite 101 • Riverside, CA 92518
Page 3-3 IM 806 REV. 2/19