Reach T-3i User manual

Installation Guide
Reach T-3i
1

When you open the carton, you will have below spare parts:
PART LIST
：
NO.
DISCREPTION SPECS QTY
NO. DISCREPTION SPECS QTY
1 Main Frame
1
70 Bolt M8*45 2
12 5# Allen Wrench
1
71 Safety key
1
51 Bolt M8*16 4
72 Oil bottle
1
64 Lock washer 8 6
FIXING TOOLS:
5# Allen Wrench 5mm 1pc
Notice: Do not get through power before complete assembly
ASSEMBLYINSTRUCTIONS
2

Open the carton, get out the above
spare parts, and put the Main
Frame onto the level ground.
Holding the computer
frame ,use the 5# Allen wrench，
Lock the base and right upright
tube tight by screw M8*16(51)
and lock washer（64）See as left
picture.
Left side assembly method
same as right side
Pull up the uprights
AssemblyInstruction
3

Use the 5# Allen wrench (12)，lock
the
screw M8*45 (70) and lock
washer
（64）to the base frame through base
And right upright tube.
Notice: Support the upright with hand
avoid falling down to have any hurt.
Put the safety key (71) on the computer
and start your exercise.
ATTENTION
：
Please make sure all parts have been fixed properly. Before you use the
treadmill, please read the instruction carefully.
4

Pull up the base frame at
position A, till hearing the
sound that the air pressure bar
B is locked into the round tube
Support place A with hand, kick
the place of air pressure bar, then
the base frame will fall down
automatically (Please keep
anybody and any pet away the
machine when falling down)
5

BUILT UP
SIZE(mm)
1580.5*670*1327mm
POWER
As the rating label showing
FOLDED
SIZE(mm)
850*670*1470mm
MAXIMUM
OUTPUT POWER
As the rating label showing
RUNNING
AREA(mm)
400*1200mm
SPEED RANGE
0.8-12KM/H
NET WEIGHT
53KG
MAX USER
WEIGHT
100KG
1 LCD WINDOW
DISPLAY SPEED/ TIME /DISTANCE/CALORIE/ PULSE
GroundingMethods
This product must be grounded. If it should malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk of electric shock. This
product is equipped with a cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment-grounding conductor can result in
a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt
as to whether the product is properly grounded. Do not modify the plug provided with the
Product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 120-volt circuit and has a grounding plug that
looks like the plug illustrated in sketch an in following figure. Make that the product is
Connected to an outlet having the same configuration as the plug. No adapter should be
used with this product.
TechnicalParameter
6

Warning: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE CLEANING OR
SERVICING THE UNIT.
Clean: General cleaning or the unit will greatly prolong the treadmill.
Keep treadmill clean by dusting regularly. Be sure to clean the exposed part of the deck on either side of the walking belt and
also the side rails. This reduces the buildup of foreign material underneath the walking belt by wearing the clean running shoes.
Warning:Always unplug the treadmill from the electrical outlet before removing the motor cover. At least once a
Year remove the motor cover and vacuum under the motor cover.
RUNNING BELT AND DECK LUBRICATION
This treadmill is equipped with a pre-lubricated, low maintenance deck system. The belt/ deck friction may play a major role in
the function and life of your treadmill, thus requiring periodic lubrication. We recommend a periodic inspection of the deck. You
need contact with our service center if you find the damage of the deck.
We recommend lubrication of the deck according to the following timetable:
Light user (less than 3 hours/ week) annually
Medium user (3-5 hours/ week) every six months
Heavy user (more than 5 hours/ week) every three months
We recommend that you buy the lubrication from our distributor or directly to our company.
Attention: Any repair need the professional technician.
1, we suggest that you should cut off the power for 10Mints after keep running 1.5HS, so that it’s good for
maintain the treadmill.
2, For avoiding the slipping during running , the belt not too loose; for avoiding the more abrasion between the
roller and belt and maintain the machine’s good running ,the belt not too tight. You can adjust the distance
between plates and belt , the belt be away from the plates about 50-75mm on both sides ,if the best not too tight
and loose.
RUNNING BELT ADJUSTMENT
7

Place treadmill on a level surface. Run
Treadmill at approximately 6-8KM/H,
checking the running condition.
If the belt has drifted to the right, pull out of
the save clock and switch, turn the right
adjusting bolt 1/4 turn clockwise, then start
running until centering the belt. PIC A
If the belt has drifted to the left ,pull out of
the safety clock and switch, turn the left
adjusting bolt 1/4 turn clockwise ,then start
running until centering the belt .PIC B
Timely adjust the tightness of the belt,
for
the looseness after a period of time
running.
Pull out of the safety clock and
switch , turn
the left and right adjusting bolt
1/4 turn
clockwise ,then re-start running,
confirm the
belt-tightness until the belt be
right tightness.
PIC C
Center the running belt
8

16

NO.
DISCREPTION
SPECS
QTY.
NO.
DISCREPTION
SPECS
QTY.
1
MAIN FRAME
1
43
Rubber pad 2
2
2
BASE FRAME
1
44
Magnetic ring
1
3
Upright bracket
2
45
Blue single wire
1
4
Bottle holder
2
46
bolt
M8*25
1
5
Motor frame
1
47
Lock nut
M6
2
6
Computer Bracket
1
48
Bolt
ST4.2*28
2
7
rubber pad
4
49
Bolt
M6*45
1
8
TURNINGBUSHING
2
50
Bolt
M6*65
2
9
FRONT ROLLER
1
51
Bolt
M8*16
8
10
REAR ROLLER
1
52
Bolt
M8*12
2
11
CYLINDER
1
53
Bolt
M8*40
4
12
5#ALLEN WRENCH
5mm
1
54
Bolt
M10*70
2
13
Incline motor
1
55
Lock washer
8
7
14
DC motor
1
56
Bolt
ST4.2*12
7
15
Running board
1
57
Bolt
M5*8
4
16
Adjustable wheels
2
58
Lock washer
M8
6
17
Tube cap
2
59
Bolt
M8*30
1
18
Motor cover
1
60
Bolt
ST4.2*19
4
19
Motor bottom
cover
1
61 Bolt M10*20 2
20
Side rails
2
62
Bolt
ST4.2*19
6
21
Right back end
cover
1
63 Lock washer 5 2
22
Left back end cover
1
64
Lock washer
8
16
23
Incline frame
1
65
Lock washer
6
3
24
Motor belt
1
66
Lock washer
10
2
25
Power wire buckle
1
67
Lock washer
8
6
26
Running belt
1
68
Bolt
M6*37
2
27
Foot pad
4
69
Bolt
M6*35
8
28
ring wire plug B
2
70
Bolt
M8*45
4
29
transport wheel
2
71
Safety key
1
30
Roller Cover
2
72
Oil bottle
1
31
Power wire
1
73
Lock nut
M10
2
32
Switch
1
74
Bolt
ST4.2*20
4
33
Foam
2
75
Bolt
ST4.2*13
9
34
cone-shape
cushion
2
76 Bolt M5*15 2
35
Computer button
cover
1
77 Lock washer 10 2
36
Computer cover
1
78
Bolt
M10*55
1
37
Hand pulse with
incline+/incline-
1
79 Lock washer 5 2
38
Computer
1
80
Bolt
M10*55
1
39
Hand pulse with
speed+/speed-
1
81 Cushion
4
40
Controller
1
82
Bolt
M8*42
1
41
Computer bottom
wire
1
83 Belt guide
2
42
Computer upper
bottom wire
1
84 Bolt ST4.2*12 4
17

Fault Code Main reason Solution
E01 The wire from computer to bottom
control board didn’t connected well
1
．
Check the connection wire between
Computer and control board was
well
connected.
2 ．Make sure the IC on the control board
was well inserted. If not re-insert.
3．Abnormal power supply in control board.
Please change a new control board.
E02 Protect the exploding
1
．
Bad contact with motor open circuit.
Please change a new motor or check the
connector.
2．Power tube was puncture. Please change
a new Power tube or control board.
E05 OvercurrentProtection
1．Overloaded。
2．Running board with heavy resistance.
Need to be oiled
3．Damage in Motor. Change a new motor.
E06 Control board self-checking
E08 EEPROMdamage Change the control board
18