Realfiction DREAMOC XXL3 User manual

DREAMOC XXL3 - ASSEMBLY GUIDE
VERSION 1.3 - ORIGINAL ASSEMBLY GUIDE
It is important to read this assembly guide before using the Dreamoc, and to follow advices and instrucons on
safety, operaon and general use to get the best possible experience with your Dreamoc.
The Dreamoc is designed to showcase products and other objects in combinaon with free oang 3D video
animaons. Realcon and Dreamoc are registered trademarks owned by Realcon ApS.

2
Content:
When receiving the Dreamoc 3
Tools you will need for assembling the Dreamoc XXL3 4
Assembling the Dreamoc XXL3 5
Assembling the chassis 5
Mounng the picture engine 7
Mounng the opcs 8
Placing the white center stage 10
Aaching the side plates 11
Sliding on the brushed steel proles 12

3
When receiving the Dreamoc
The Dreamoc XXL3 comes in sturdy transport cases (plywood) that holds all the dierent parts.
Please note that we cannot be hold responsible for any damage or failure that has occurred due to the use of
third party constructed ight case or packaging. This limitaon shall also apply if the original packaging has been
altered in any way.
Package content
1. Umbraco key set
2. Umbraco screwdriver
3. Keys for the display
4. Remote control / 2 x AAA baeries
5. Cleaning cloth
6. 4 x corner prole extensions
7. 12 x brushed steel proles (three dierent
lenghts)
8. 8 x screen brackets
9. Top lid with venlaon holes
10. 4 x safety laminated Crystalline
TM Opcs
11. 4 x 43“ LCD screens
12. Grounding cable
13. Assorted screws for assembling the display
14. White center stage plate
15. 4 x top side plates
16. 4 x boom side plates
17. 4 x adjustable feet
1 x top secon frame
4 x support beams
1 x center secon frame
1 x boom secon frame
4 x corner proles
Addional items

4
Tools you will need for assembling the Dreamoc XXL3
• Small at screwdriver and Unbrako tools
• We recommend using safety gloves and sucon cops appropriate for handling glass.
• spirit level
Setup me and persons needed
Seng up the display can be done by 2 persons in around 2 hours.

5
Assembling the Dreamoc XXL3
Please note to only use black screws for all parts of the assembling that faces downwards towards the opcs.
This is to eliminate possible reecons from the screws.
Assembling the chassis
1. Take out the pre-assembled boom secon frame and mount the adjustable feet from below. Use the spirit
level and adjust the feet in order to make the display correctly levelled.
2. Adjust the powercable underneath the boom secon frame
3. Mount the 4 corner proles using 4 screws for each corner

6
4. Li in centre secon frame with the white plate facing up and the keyhole facing in the direcon where you
want the back door. Fasten the center secon with 4 screws in each corner.
5. Mount the 4 support beams with 4 screws per beam. ( 2 in each side of the beam)
6. Li in the top secon frame so it sits on the support beams. Fasten it with 2 screws in each corner.

7
Mounng the picture engine
7. Place the four LCD screens, by liing them onto the top secon frame separately. Secure each screen with 2
bracket and fasten with 2 screws each. For the front and back of the display, the brackets are fastened from the
top, and for the sides the brackets are fastened underneath the top secon.
8. Aach the corner prole extensions with 4 screws.

8
9. Connect each LCD screen with the HDMI, IR (infrared) and power cable.
Power cable HDMI cable IR cable HDMI cable IR cable
Mounng the opcs
10. For each side of the display, slightly loosen the 4 screws on the support rail. This is to allow a bit of room
between the opcs to begin with, in order to fully adjust and push the opcs together aerwards.
(Warning! beware not to loosen the screws too much, as the opcs support rail will then slip o and not hold
the glass opcs in place.)
11. Gently li each of the glass opcs in place, by resng the top of the opcs on the lamp housing, and then
gently ng them securely in place on the support rail. We recommend using appropriate gloves and sucon
cups for handling glass.
Important! Make sure to protect each corner of the opcs when placing them on the support rail, to avoid
damaging the opcs.
Support rail
Lamp housing

9
12. Complete by gently pushing the opcs together to eliminate space between each of them. Secure by fasten-
ing the screws on the support rail to lock the opcs in place.
Grounding the chassis
13. Mount the yellow-green ground cable from the display chassis to your appropriate electrical installaon
ground. Then adjust the placing of the power cable, so it runs vercally down the support beam.

10
Placing the white center stage
14. Place the white center stage plaorm by rst opening all the stage arms underneath the display.
15. Then mount the center stage plaorm from below and lock the arms in place to secure it.
When placing a physical object inside the display, we recommend being two persons.
Stage arm
16. Turn on the display and check that all four sides are playing the pre-loaded test content.

11
Aaching the side plates
17. Place the top lid on the display by gently liing it in place, to t the top secon of the display. Make sure
that the 2 holes in the top secon frame matches the 2 holes in the top lid. Secure the top lid with 2 screws.
If you plan on applying branding foil to the display, this should be done at this stage before aaching
the side plates. We recommend applying the branding foil while the side plates are lying on a protec-
ve surface on the oor.
18. Mount the 4 side plates for the boom part of the display, by liing in the lower part rst and then hinging
them in place to secure.

12
19. Then mount the 4 side plates for the top part of the display, and lock these in place with 4 screws each for
the front and the sides of the display, and only mount the 2 screws on top for the back of the display, so you
can easily li up the plate to access the power switch, light seng and change video content.
Sliding on the brushed steel proles
20. Aach the brushed steel proles for the corners to nish the assembling. There are 3 dierent lengths for
each corner. Remember to rst remove the protecve foil.
Back of the display: only mount
1 screw
Front + sides: mount 2 screws on
each end of the plate (4 in total per
plate)
21. Begin by sliding down the longest steel prole rst, all the way from the top and down to the boom of
the display. Make sure that the angled tap is facing downwards. Then take the second longest prole and nish
with the shortest. Warning! For the corner where the power and grounding cable is placed, make sure not to
damage the wires.

13
Assembly is now nished. Please see the user manual for how to operate the display.

14
Realcon and Dreamoc are registered trademarks owned by Realcon ApS. Other marks may be menoned here in that be-
long to other companies. © 2018 Realfcion Aps. All rights reserved.
Realcon Aps | Øster Alle 42, 7th oor | DK-2100 Copenhagen Ø Denmark | Phone: [phone]
For further informaon and pricing please contact Realcon
Phone: [phone]
email: contact@realcon.com