Realfiction DEEPFRAME BASIC User manual

1
DEEPFRAME - ASSEMBLY GUIDE
VERSION 1.1 - ORIGINAL ASSEMBLY GUIDE
It is important to read this manual before using the DeepFrame, and to follow advices and instrucons on safety,
operaon and general use to get the best possible experience with your DeepFrame. DeepFrame is a revoluonary
new type of mixed reality display that enables digital content to appear as a hologram on top of reality seen
through the lens. The window-like display consists of a high-precision opcal lens that can be mounted on the
oor stand (oponal accessory) or hang suspended in wires.
The DeepFrame is patent-pending. Realcon and DeepFrame are registered trademarks owned by Realcon ApS.

2
Content:
When receiving the DeepFrame 3
Setup me and persons needed 4
Assembling the DeepFrame 5
Assembling the oor stand for DeepFrame Basic Kit 6
Aaching the DeepFrame Opc to the oor stand 8
Assembling the OLED mount 9
Aaching your VESA mount 11
Aaching the OLED screen to the OLED mount 13
Assembling the OLED housing 16

3
WHEN RECEIVING THE DEEPFRAME
Please note that DeepFrame needs to be combined with an HD or 4K screen (not included) for projecng the
digital content through the opcal lens. We recommend using a 65” 4K curved OLED screen together with
the OLED mount kit (oponal accessory).
Why should I use a curved OLED screen?
The curved OLED, mounted on our oponal OLED mount kit, will curve the image to follow the curvature of
the DeepFrame lens, thus straightening out the reected image and minimizing any perceived distorons in the
image contents. Further the OLED technology has an extremely good contrast and color performance, which
helps and opmizes the 3D eect.
What happens if I use a at LCD screen instead?
When using any at display, you should know that the reected virtual image will be curved and be distorted.
On the center part of the image, the distoron is not really noceable, but the further to the side your contents
are on the screen, the more they will seem distorted and skewed in perspecve.
If you use an LCD screen, please make sure to try and minimize the so called black level in the screen. This is the
amount of light shining through the black parts of the image. A high black level will result in a grey haze being
reected by the DeepFrame, which does not look good and lowers the overall 3D eect and wow-factors.
1. 1 x Glass opc 2. 1 x Frame

4
Setup me and persons needed
Seng up the display can be done by 2 persons in around 2 hour.

5
DEEPFRAME BASIC KIT: INTRODUCTION TO THE DEEPFRAME
OPTICAL LENS
The DeepFrame Basic Kit comes in 1 ight case.
1. As a general rule, this display is designed to be built into custom installaons, as each component can be
ordered separately. You can of course also choose to purchase a complete DeepFrame setup.
2. When looking at the DeepFrame Opcal Lens it is worth nocing that the inside is the most delicate part,
which means it should be taken very good care of.
3. The frame holding the Opcal Lens is both wide and robust since the display is meant to be integrated into
more permanent installaons.
4. To allow this, the frame presents several mounng soluons – one being the center point axis, which you can
use to rotate the enre opcal lens, and aaching it to the oor stand. If needed, you can also choose to detach
the center point axis and instead aach your own type of mount soluon in that spot.

6
6. You’ll also see addional holes for aaching other types of mounng soluons if needed, as well as main grip for your hands.
5. When further examining the frame, you’ll see the embedded y point on all 4 corners, which
allow the frame to hang suspended in wires.
ASSEMBLING THE FLOOR STAND FOR DEEPFRAME BASIC KIT
1. Open the ight case and begin by taking out each of the oor stand legs one by one.

7
2. Aach the connector blocks on each side and fasten with the small screws using an umbraco key. Make sure
the screws are ghtly fastened.
3. Adjust the feet to make sure the stand is correctly balanced.
4. Aach the security clamps on the boom of the stand to lock the posioning of the legs in place.

8
5. When the oor stand has been assembled, ip the ight case around to reveal the DeepFrame Opcal Lens.
Aaching the DeepFrame Opc to the oor stand
Important: We recommend being 3 persons for this.
6. Gently li out the Opcal Lens Opc and rest in on a sheet of protecve foam on the oor.
7. Li it up, and then over the oor stand, before gently lower it down to secure the locks on the frame onto
the connector blocks.

9
8. Rotate the Opcal Lens unl you reach the right posioning, and then ghten the locks to secure it in place.
2. Place the 2 curved secons with the opening facing each other, to form the top and boom of the OLED Mount.
To tell the top and boom apart, the boom secon has a wide incision to t the connecon cable later on.
ASSEMBLING THE OLED MOUNT
1. Unpack all the parts and place them on a sheet of protecve foam on the oor as shown here.
Important: If you are installing DeepFrame in public spaces where people can potenally touch the display, we
always recommend installing an extra safety device to prevent the locks from opening by accident.

10
3. Place the 2 side secons on the le and right side and make sure the notches on each side secon matches
the notches on the curved secons.
4. Take the rst side secon and slide it on top, to t the right side of the 2 curved secons. Fasten with 3 short
screws in each end. When all the screws are ed, ghten them completely with the Umbraco key.
5. Then repeat the same procedure with the le side.
6. Take the Vesa Mount Holder and place it in the middle of the OLED Mount with the at side facing
upwards. Aach it with 4 screws each for the top and boom. When all the screws are ed, make sure to
ghten them completely.

11
7. Raise the OLED Mount Kit upwards and the aach the stabilizer inside, with the at side towards you. Aach
it with 1 screw for the top and boom.
Aaching your Vesa mount
8. Flip the OLED Mount around so the curved side faces downwards, so the Vesa Mount Holder is visible.
9. Aach the two brackets from your Vesa Mount and fasten with the supplied bolts.

12
10. Then click the at panel bracket in place and securely lock it in place by ghtening the screws.
11. Now, li the OLED Mount in place on the OLED Stand. You can easily adjust the lng if needed.
13. When you are sased, remember to secure it in place by pushing down on the lock.

13
ATTACHING THE OLED SCREEN TO THE OLED MOUNT
1. Open the box holding OLED Screen and remove the Styrofoam sides.
3. Li the OLED Screen in place, one side at a me, by hinging the bracket to the OLED Mount.
Then very gently hinge the other side on, thereby curving the OLED Screen to t the OLED Mount.
Important: Do not apply pressure to the boom part of the OLED Screen, instead allow the boom corner to
bend in a dierent radius than the top, leaving a wider gap
2. On the backside of the OLED Screen, guide the bracket through the boom of the T-hole rst and then slide
it up and out towards the corner of the screen. Secure it in place using a piece of tape. Repeat this for the other
side as well.

14
4. When both sides are hinged in place, guide the screws through the holes and fasten with the wing nuts and
washers to secure it in place, one side at a me.
5. Mount the 2 Corner Protectors on each side using 2 screws on the side and one from below.

15
5. Locate the Sound Bar and li it in place on the OLED Floor Stand
7. Take the Connecon Cable and mount it to the Sound Bar. Fasten with the 2 small black screws.
Beware not to pull the cable towards you as this might damage the part where the cable connects to the screen.
6. Then mount the oponal Top Protector

16
ASSEMBLING THE OLED HOUSING
1. Unpack all the parts and place them on a sheet of protecve foam on the oor. Please note that all the screws
needed for assembling are already ed. For fast assembling, we recommend not removing the screws or ngs.
3. Aach one of the black aluminum proles to the side frame and lock it in place using an umbraco key.
4. The take the second black aluminum prole and aach it in the same way.
2. Take the top plate and slide it into the groove on one of the side frames.

17
5. Li the other side frame in place on top and lock it in place.
6. Now, place the OLED Housing with the top plate facing upwards.
7. Aach the fabric sides by pushing the rubber seam into the groove on the side frames and front. For each
side, start with the corners and progress to the middle of the fabric unl it is completely aached and stretched.

18
8. To remove the fabric sides again use the lile pull-tab.
9. When ordering the OLED Housing you can upload your own artwork for the fabric sides, and also re-order new
ones when needed
Assembly is now nished. Please see the user manual for how to operate the display.

19
Realcon and Dreamoc are registered trademarks owned by Realcon ApS. Other marks may be menoned here in that
belong to other companies. © 2018 Realfcion Aps. All rights reserved.
Realcon Aps | Øster Alle 42, 7th oor | DK-2100 Copenhagen Ø Denmark | Phone: [phone]
For further informaon and pricing please contact Realcon
Phone: [phone]
email: contact@realcon.com