Realfiction DEEPFRAME BASIC User manual

1
DEEPFRAME ONE - ASSEMBLY GUIDE
VERSION 1.1 - ORIGINAL ASSEMBLY GUIDE
It is important to read this assembly guide before using the DeepFrame One, and to follow advices and
instrucons on safety, operaon and general use to get the best possible experience with your DeepFrame One.
The DeepFrame One is designed to showcase products and other objects in combinaon with free oang 3D
video animaons. Realcon and DeepFrame are registered trademarks owned by Realcon ApS.

2
Content:
When receiving the DeepFrame One 3
Setup me and persons needed 4
Assembling the DeepFrame One 5
Assembling the display 5
Aaching the OLED screen to the OLED housing 9
Connecng the media player and wires 13
Aaching the speaker module 15

3
When receiving the DeepFrame One
The DeepFrame One comes in two ightcases that holds all the dierent parts.
Please note that we cannot be hold responsible for any damage or failure that has occurred due
to the use of third party constructed ight case or packaging. This limitaon shall also apply if the
original packaging has been altered in any way.
Package content
1. 1 x Glass opc
2. 1 x Installaon & Service Toolbox
3. 2 x Leg Frames
4. 1 x 4K curved OLED 65” TV
5. 1 x Opc Safety Bracket
6. 1 x Speaker module
7. 1 x Spirit level
8. 1 x OLED housing
9. 1 x Brightsign Media Player
10. 1 x Top protector
11. 2 x Extension rods
12. 2 x Screen protectors
Addional items

4
Setup me and persons needed
Seng up the display can be done by 2 persons in around 2 hour.

5
ASSEMBLING THE DEEPFRAME ONE
For assembling the display we recommend being to persons.
Unpacking the display
DeepFrame One comes in 2 ight cases.
1. Begin by opening the tallest ight case rst and locate the Toolbox inside, then set this ight case aside.
2. Now open the shorter ight case and locate the Speaker Module. Li it out and set it aside for now
3. Remove all the assembly parts from the boom of the ight case and unpack them.

6
5. When the bolts have been removed, li the OLED Housing out from the ight case and place it on the oor.
6. Place the spirit level on top and adjust the feet using a spanner size 13 unl the OLED Housing is correctly levelled.
4. Remove the transport bolts in each side to unlock the OLED Housing from the ight case.
Use the wrench and Umbraco key size 8 for this.
7. In the other ight case, take out the rst Leg Frame and aach it with 2 bolts in the lowest of the grooves underneath
the OLED Housing, using spanner size 19. Then, take out the second Leg Frame and aach it in the same way.

7
8. Take out the Opc Safety Bracket and slide it down into the holes on the top of each Leg Frame, as this will
set the correct distance between the leg structures and provide support when mounng the DeepFrame Opcal
Lens aerwards.
9. Now, take out the DeepFrame Opcal Lens from the ight case and gently li it over to the Leg Frames and
aach the lower part rst by sliding the notches in to t the pins on each Leg Frame. Then slowly raise it upwards
to rest it safely on the Opc Safety Bracket on top.

8
10. Secure the DeepFrame Opcal Lens in place using 1 long black 10mm bolt in each side – make sure you do
not use the transport bolts you have removed previously.
IMPORTANT: In order to proceed assembling the display, make sure that all the bolts are ghtened completely,
both underneath the OLED Housing and on the Leg Frames now supporng the weight of the DeepFrame
Opcal Lens. We recommend that the OLED Housing and DeepFrame Opcal Lens are posioned as far away
from each other as possible, as this will allow more space to aach the OLED Screen aerwards.
11. When all the bolts are secured and ghtened, nish by removing the Opc Safety Bracket, making sure not
to scratch the inside of the DeepFrame Opcal Lens.

9
2. For one side plate at a me, remove the 2 screws located at the top and then gently push out the plate just
enough to free it at the top and then li it up and out. Beware: Do not to pull the side plate too far down as
this will damage the metal pins in the boom. Repeat this for the second side plate as well.
1. To begin with we recommend removing the 2 side plates and front plate on the OLED Housing, as this will
create more room to work with when aaching the OLED Screen.
ATTACHING THE OLED SCREEN TO THE OLED HOUSING
3. Take o the front plate by removing the 2 screws located at the boom and then gently push out the plate and li
it down and out. Beware: Do not to pull the front plate too far up as this will damage the metal pins in the top.

10
4. Loosen the screw for the Screen Adjuster located in each side.
5. Tilt it forward and then ghten the screws again.
6. Remove the top brackets on the Sound Bar Holders.
7. Open the box holding OLED Screen and remove the Styrofoam sides

11
8. Locate the Sound Bar and li it in place on the Sound Bar Holders. Use the rubber cushions to protect the
Sound Bar. Important: Make sure that the round speakers are free to move up and down when turning the
OLED Screen on and o.
10. Locate the 2 Screen Brackets and remove the wing nuts and washers.
9. Aach the top brackets of the Sound Bar Holders again to secure the Sound Bar in place.
11. On the backside of the OLED Screen, guide the bracket through the boom of the T-hole rst and then
slide it up and out towards the corner of the screen. Secure it in place using a piece of tape. Repeat this for the
other side as well.

12
12. Li the OLED Screen in place, one side at a me, by hinging the bracket to the OLED Mount.
13. Then very gently hinge the other side on, thereby curving the OLED Screen to t the OLED Mount.
Important: Do not apply pressure to the boom part of the OLED Screen, instead allow the boom corner to
bend in a dierent radius than the top, leaving a wider gap!
14. When both sides are hinged in place, guide the screws through the holes and fasten with the wing nuts and
washers to secure it in place, one side at a me.
15. Mount the 2 Corner Protectors on each side using 2 screws on the side and one from below.

13
Connecng the media player and wires
1. In the box for your OLED Screen take the long Connecon Cable Extender and remove the plasc protecon.
16. (Oponal) Then mount the oponal Top Protector.
2. Aach the Black Cable Lock to the Connecon Cable Extender and mount it to the Sound Bar. Fasten with
the 2 small black screws.
3. Aach the Connecon Cable ed on the OLED Screen to the Connecon Cable Extender and mount the
clear plasc Cable Protector to lock them together.

14
4. Mount the Media Player in the right side using 2 small clamping screws.
5. Place the Power Strip under the Sound Bar.
6. Connect the HDMI cable from the Media Player to the Sound Bar.

15
Aaching the Speaker Module
1. Remove the protecve bag from the Speaker Module.
2. Gently li it over to the Leg Frames underneath the DeepFrame Opcal Lens and aach the lower part rst
by sliding the notches in to t the pins on each Leg Frame. Then slowly raise it upwards and fasten with 1 long
black 10mm bolt in each side.
3. In one side of the Speaker Module you will see the speaker cable. The next step is to guide this cable through the
Leg Frame. Under the DeepFrame Housing, locate the 2 plasc plugs in the Leg Frame and remove the le one.

16
4. Use the search spring from the Toolbox and guide it through the small hole in the Leg Frame located under
the Speaker Module, unl it comes out of the hole where you removed the plasc plug.
5. Aach the speaker cable to the search spring using a piece of tape and gently pull it back through the Leg Frame.
6. Connect the speaker cable to the Sound Bar (Speaker Out, Stereo (8 Ohm)).
7. Finish by aaching the grounding cable to a screw in the chassis and aach it to your appropriate electrical installaon.

17
8. Lastly, aach the 2 side plates, the front plate and the plates in the boom on the OLED Housing again.
Assembly is now nished. Please see the user manual for how to operate the display.

18
Realcon and Dreamoc are registered trademarks owned by Realcon ApS. Other marks may be menoned here in that
belong to other companies. © 2018 Realfcion Aps. All rights reserved.
Realcon Aps | Øster Alle 42, 7th oor | DK-2100 Copenhagen Ø Denmark | Phone: [phone]
For further informaon and pricing please contact Realcon
Phone: [phone]
email: contact@realcon.com