Recycled Furniture RFPY1220 User manual

EverYear Raised Beds
Assembly Guide
0800 1777 052
AAA-00-000016-RF

Notes:
2

Assembly Guide Overview
Two People required
for safe assembly
3
This instruction covers the the complete EverYear
range, as such some views and steps may look
different or not be required during assembly.
See bill of material list below to ensure you have
all parts for your planter.
Table continued overleaf
Product Code Description
RFPY1220 EverYear Raised Bed L600 x W640 x H100
RFPY1221 EverYear Raised Bed L600 x W640 x H200
RFPY1222 EverYear Raised Bed L600 x W640 x H300
RFPY1223 EverYear Raised Bed L600 x W640 x H400
RFPY1224 EverYear Raised Bed L1200 x W640 x H100
RFPY1225 EverYear Raised Bed L1200 x W640 x H200
RFPY1226 EverYear Raised Bed L1200 x W640 x H300
RFPY1227 EverYear Raised Bed L1200 x W640 x H400
RFPY1236 EverYear Raised Bed L1200 x W1240 x H100
RFPY1237 EverYear Raised Bed L1200 x W1240 x H200
RFPY1238 EverYear Raised Bed L1200 x W1240 x H300
RFPY1239 EverYear Raised Bed L1200 x W1240 x H400

Corner Batton
Support Batton
Plank (600/1200)
Step
1
Sort materials supplied into planks, corner battons and support
battons. Please note that some planters have 2 different size
planks supplied.
4

Screw Holes
Plank
Corner Batton
Step
2
Rest Plank(s) onto a flat clean surface and place the Corner Batton
over the top of the Planks and secure suing screws supplied.
Do not over-tighten screws during assembly as
small adjustments will help parts fit.
Step
3
5
This completes the
assembly of the
Front/Rear Panel of the
Planter.
Repeat the process for
the other set of
Front/Rear Planks
Repeat step 2, this will create a second side.
Note: Number of planks required
will change based on product
height. (See Table)
Please ensure all planks used
are the same length.
Important: If planter is rectangular
this will be the shorter lengths.
Planter Height
(MM)
Planks
Required
100 1
200 2
300 3
400 4

Plank 2
Plank 2
Side
Side
Side
Side
Plank 2
H
DETAIL H
SCALE 1 : 5
Side
Plank 2
Step 4
Take half te remaining planks and secure them to the sides as
below. See detail for correct allignment.
Do not over-tighten screws during assembly as
small adjustments will help parts fit.
Step 5
6
Do the same with the remaining planks on the opposite side, this
will complete the RFPY1220 - 1223 planters.
Allignment Detail
Note: If you have purchased a
rectanguar planter this step
should use the longer planks.

1240
1200
Support BattonSupport Batton
Step 6
Finally if a side is above 640mm screw a support batton to the
center, see below.
Do not over-tighten screws during assembly as
small adjustments will help parts fit.
7

8
CONTACT DETAILS:
Email : [email protected]
Web : www.recycledfurniture.co.uk
Tel : [phone]
NBB Recycled Furniture,Unit 5, 145 Sterte Road,Poole, Dorset BH15 2AF
THANK YOU
FOR PURCHASING THIS PRODUCT
All Parts and Fixings checked by:
Print Name: Signature