Red Arrow WILSON User manual

110V 30W LED GLOBE LIGHT
MODELS: GLS30YPW, GLE30YPW
PRODUCT INSTRUCTIONS
110V 30W LED GLOBE LIGHT
MODELS: GLS30YPW, GLE30YPW
PRODUCT INSTRUCTIONSINSTALLATION INSTRUCTIONS
Red Arrow Trading Ltd
Elsworth House, Herries Road South
Sheeld, S6 1QS
Tel: [phone] Fax: [phone]
Email: [e-mail] Web: www.redarrowtrading.com
22W LED WILSON BULKHEAD WITH MICROWAVE SENSOR
MODELS: WIL22LEDMS & WIL22LEDCMS
S A F E T Y W A R N I N G
• The installaon should be carried out by a qualied electrician in compliance with the current edion of the IEE Wiring Regulaons.
• Prior to installaon, carry out the necessary risk assessment considering the people who could be at risk, the level of risk and the precauons required to
control the risk
• Ensure that the circuit supply is isolated either by the circuit supply fuse being removed or the applicable circuit breaker being turned o before installaon
or any maintenance.
• Check the total load on the circuit ensuring the luminaire does not exceed the rang of the circuit cable, fuse or circuit breaker.
• If the ng incorporates control gear, ensure careful sizing to avoid instances of nuisance tripping of the protecve device used in the installaon.
• Follow the provided installaon instrucons, using the xings supplied or recommended.
I N T R O D U C T I O N
The 22W LED Wilson Bulkhead with Microwave Sensor is suitable for com-
mercial kitchens, leisure centres and meeng room applicaons.
B O X C O N T E N T S
1 x 22W LED Wilson Bulkhead with Microwave Sensor
1 x Diuser removal tool
2 x Expansion plugs
2 x Screws
S P E C I F I C A T I O N
86lm/W (+/- 10%)
Dimensions: Ø: 432 x D: 108mm
Finish: White/Chrome
LED: 108pcs of SMD 2835
Working Temperature: 5°C -55°C
Automac
Circuit Breaker
Type
B6 B10 B13 B16 B20 C10 C13 C16 C20
Rated Current
(Amperage)
6A 10A 13A 16A 20A 10A 13A 16A 20A
Installaon
(mm2)
1.5 1.5 1.5 1.5 2.5 1.5 1.5 1.5 2.5
Connecon Qty
(Max)
36pcs
@
230Vac
48pcs
@
230Vac
48pcs
@
230Vac
48pcs
@
230Vac
85pcs
@
230Vac
48pcs
@
230Vac
48pcs
@
230Vac
48pcs
@
230Vac
85pcs
@
230Vac
220-
240V 22W LED 4000K
IP20 1710lm/
2090lm IK06

22W LED WILSON BULKHEAD WITH MICROWAVE SENSOR
MODELS: WIL22LEDMS & WIL22LEDCMS
INSTALLATION INSTRUCTIONS
Red Arrow Trading Ltd
Elsworth House, Herries Road South
Sheeld, S6 1QS
Tel: [phone] Fax: [phone]
Email: [e-mail] Web: www.redarrowtrading.com
I N S T A L L A T I O N I N S T R U C T I O N S
1. Select the required posion for the Bulkhead and provide a suitable power supply to this point, taking into account the possible power
entry points of the Bulkhead.
2. Remove the diuser cover from the body.
3. Feed the power cables into the enclosure.
4. Fix the base to the wall or ceiling as required. Locate the joists, be aware of water pipes and electric cables when applying the xing
screws.
5. Connect the mains supply cables to the terminal blocks supplied as follows:
• LIVE - (brown) to terminal marked L
• NEUTRAL - (blue) to terminal marked N
• EARTH - (green/yellow) to terminal marked . N.B. These Bulkheads must be earthed.
6. Ensure there are no exposed conductors, loose strands or trapped insulaon.
7. Ret the diuser cover.
8. Switch on the power supply.
9. The Microwave Sensor has 3 dials (lux level, me & sensivity range). Adjust the dials to suit your requirements and maximise energy
savings.
IMPORTANT: Ensure that ALL electrical connecons are ght with no loose strands, including factory made connecons.
The ng must not, under any circumstances, be covered with any insulaon materials and must not be installed close
to ammable materials.

110V 30W LED GLOBE LIGHT
MODELS: GLS30YPW, GLE30YPW
PRODUCT INSTRUCTIONS
110V 30W LED GLOBE LIGHT
MODELS: GLS30YPW, GLE30YPW
PRODUCT INSTRUCTIONSINSTALLATION INSTRUCTIONS
Red Arrow Trading Ltd
Elsworth House, Herries Road South
Sheeld, S6 1QS
Tel: [phone] Fax: [phone]
Email: [e-mail] Web: www.redarrowtrading.com
22W LED WILSON BULKHEAD WITH MICROWAVE SENSOR
MODELS: WIL22LEDMS & WIL22LEDCMS
M I C R O W A V E S E N S O R I N D U C T I O N R A N G E D I A G R A M
C O N N E C T I O N I L L U M I N A T I O N D I A G R A M
REACH SETTING (SENSITIVITY)
Reach is the term used to describe the radius of the circular detecon zone produced on the ground. Aer mounng the
sensor light at a height of 2.5m, turn the reach control completely in an an-clockwise direcon to select the minimum
reach (approx. 1m radius), and turn the reach control completely in a clockwise direcon to select the maximum reach
(approx. 8m radius). The LED indicator will ash when the reach control is rotated. It ashes 1 to 8 mes, represenng
1m to 8m for the radius of the detecon zone.
NOTE: The above detecon distance is measured using a person who is between 1.6m~1.7m tall with an average build,
moving at a speed of 1.0~1.5m/sec. If any of these variables change, the detecon distance will also resultantly change.
TIME SETTING
The light can be set to stay ON for any period of me between approx. 8 seconds (dial turned fully an-clockwise) and a
maximum of 12 minutes (dial turned fully clockwise). Any movement detected during the ‘on’ me will reset the mer.
The LED indicator will ash when adjusng the me seng dial.
NOTE: Aer the light switches o, it takes approx. 1 second before it is able to start detecng movement again. The light
will only switch on in response to movement once this period has elapsed.

22W LED WILSON BULKHEAD WITH MICROWAVE SENSOR
MODELS: WIL22LEDMS & WIL22LEDCMS
INSTALLATION INSTRUCTIONS
Red Arrow Trading Ltd
Elsworth House, Herries Road South
Sheeld, S6 1QS
Tel: [phone] Fax: [phone]
Email: [e-mail] Web: www.redarrowtrading.com
G U A R A N T E E
This product is guaranteed for a period of 3 years from the date of purchase.
The guarantee is invalid in the case of improper use, tampering, removal
of the Q.C. date label, installaon in an improper working environment
or installaon not according to the current edion of the I.E.E. Wiring
Regulaons (BS7671).
The guarantee is also invalidated if the luminaire has been Mega tested.
Should this product fail during the guarantee period it will be replaced free
of charge, subject to correct installaon and return of the faulty unit. We
do not accept responsibility for any installaon costs associated with the
replacement of this product. Your statutory rights are not aected. We
reserve the right to alter specicaons without prior noce.
M A I N T E N A N C E
• This ng will require roune cleaning if used in adverse (dust,
paint, welding, oils etc) environments.
• When this ng comes to the end of it’s life or you choose to
replace it, please do not dispose of it with your normal household
waste. Please recycle where the facilies exist, check with your
local authority or retailer for suitable opons.
LIGHT-CONTROL SETTING
The chosen light response threshold can be innitely from approx. 2-2000lux. Turn it fully an-clockwise to select dusk-
to-dawn operaon at about 2 lux. Turn it fully clockwise to select daylight operaon at about 2000lux. The dial must be
turned fully clockwise when adjusng the detecon zone and performing the walk test in daylight.
T R O U B L E S H O O T I N G
Malfuncon Cause Remedy
The load will not work. Wrong light-control seng Adjust the seng
Load is faulty Change the load
Mains switch is OFF Switch ON
The load is always on. Connuous movement in the detecon zone Check the zone sengs
The load works
without any idenable
movement
The sensor is not mounted for detecng movement
reliably
Securely mount the enclosure
Movement occurred, but not idened by the sensor
(movement is behind a wall, movement of a small
object is in the immediate lamp vicinity etc.)
Check the zone sengs
The load will not work despite
movement
Rapid movements are being surpressed to minimize
malfunconing or the detecon zone you have set is
too small
Check the zone sengs