
CONNECT. MONITOR. CONTROL. © 2014 Red Lion Controls. All Rights Reserved 2
Quick Start Guide
3. Start BlueVue Device Manager Software
1. Download and install the latest version of BlueVue Device Manager from
www.redlion.net.
2. When launched, it will attempt to connect to 192.168.0.1 by default, once
connected to the modem, the Modem Diagnostic window will open. (Note
that 192.168.0.1 connects to the Ethernet cable. To connect to the USB
port use 192.168.111.1):
Troubleshooting: If BlueVue displays “Detecting Modem at
192.168.0.1” indefinitely, then:
• Make sure the modem is powered on.
• Check the Ethernet Link LED on the modem. If it’s off, it usually means you
have a problem with the Ethernet cable or with your computer’s network
card.
• Close all other network connections (such as WiFi)
• Set your computer to obtain an IP address automatically
4. Confirm that the modem is acquiring a cellular signal
The Signal LED should be on or flashing, indicating that the modem has
a signal. BlueVue Device Manager displays signal information in the top
right of its window; a minimum of 1 bar is required to connect to the
carrier with the modem.
Troubleshooting: If the Signal LED is off, then there may be an issue
with the antenna or cellular coverage might be too low in your current
location.
5. Activate the modem
1. Click on the ACT button located at the top. Click on the Carrier Provision-
ing button to open the Carrier Provisioning dialog.
2. In the Carrier Provisioning window, Click on the OTASP… button and then
click OK at the warning prompt.
3. Wait for the activation process to complete.
4. Confirm the success of the number's programming
5. Click on the DIAG button located at the top left to navigate to the Modem
Diagnostic screen. Check the phone number reported by the modem
under Modem Identification: it should match the MDN provided by the
Telus.
Troubleshooting: If the above does not occur, then the modem most
likely has no account. Contact the wireless service provider who pro-
vided you with the account and ask them to confirm that the phone
number and MIN/MSID assigned correspond to the modem's ESN (elec-
tronic serial number), and that the account is ready to be used.
6. Confirm the modem has successfully connected to the cellular net-
work:
• The WAN LED will be on or flashing.
•In BlueVue, click the DIAG button, the WAN IP should indicate the IP
address assigned to the modem by the cellular network.
SETUP IS COMPLETE
The modem should be ready for use as a basic internet access point.
ADDITIONAL INFORMATION
For more advanced modem configuration, consult the support section
on our website. Visit our support page at www.redlion.net to access
the modem’s documentation, as well as configuration help, trouble-
shooting and firmware & software updates. Or contact Technical Sup-
INSTALLATION AND HAZARDOUS AREA WARNINGS
Suitable for use in Class I, Division 2, Groups A, B, C and D hazardous locations,
or non-hazardous locations only. All power, input and output (I/O) wiring must
be in accordance with Class I, Division 2 wiring methods and in accordance with
the authority having jurisdiction.
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS
POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARD-
OUS.
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
AVERTISSEMENTS POUR INSTALLATION ET
ENDROITS DANGEREUX
Cet équipement est adapté pour une utilisation en Classe I, Division 2, Groupes
A, B, C et D pour endroits dangereux , ou endroits non-dangereux seulement.
Tout câblage électrique, entrée et sortie (I / O) doivent être en conformité avec
Classe I, Division 2 méthodes de câblage et conformément à l'autorité compé-
tente.
AVERTISSEMENT - RISQUE D'AVERTISSEMENT - NE DÉBRANCHEZ PAS L'ÉQUIPE-
MENT PENDANT QUE LE CIRCUIT EST DIRECT OU À MOINS QUE L'ENVI-
RONNEMENT SOIT CONNU POUR ÊTRE NON-DANGEREUX.
AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE TOUT COM-
POSANT PEUT NUIRE À LA CONFORMITÉ DE CLASSE I, DIVISION 2.