red lion IndustrialPro BT-6600 User manual

CONNECT. MONITOR. CONTROL. © 2014 Red Lion Controls. All Rights Reserved 1
QUICK START GUIDE
IndustrialProTM BT-6600 Series
Sasktel Wireless Modem
OVERVIEW
The IndustrialPro™ BT-6600 series modems are rugged wireless
modems built to provide simple and reliable communication over
Sasktel's CDMA EVDO Rev A wireless data network.
This guide covers initial activation and configuration of the following
models:
FEATURES
•CDMA EVDO Rev.A, 1XRTT, and IS95
•Diversity antenna
•EVDO Rev. A speeds of up to 3.1 Mbps
•Ethernet, Serial, and USB
•Reliable Always-on cellular link
•Rugged electrical and mechanical design
•Remote diagnostics, configuration and updates
•Router and IP Pass-through modes
•5-port Ethernet switch (on BT-6621)
•Power over Ethernet (on BT-6601EB)
•IPsec VPN multiple tunnel and 3DES|AES up to 256-bit encryption
LED INDICATORS
POWER
There are 4 methods to provide power to the modem:
1. 4-pin Molex connector - available on BT-6x00
2. 4-pin screw terminal - available on BT-6xx1/EB
3. Side mounted 2.5mm barrel connectors - available on all models
4. Power-over-Ethernet - available on BT-6x01EB
The modem requires a power source between 8 and 30 VDC to operate:
* An AC-DC power adaptor can be purchased as an accessory.
ANTENNA
An antenna with an SMA connector should be connected to the
modem. This antenna should meet the following specifications:
•Dual-band 800 & 1900 MHz
•Nominal 50 ohm impedance
•Voltage Standing Wave Radio (VSWR) less than 2.5:1
*Antennas are sold separately.
DATA INTERFACES
Ethernet: 10/100 Mbps Auto-sensing Female RJ45 port
USB: USB 2.0 Type B Female
Serial: RS-232 9 pin DCE Female, with these default settings:
SETUP
1. Setup a data account for the modem
Contact your SaskTel dealer and request a data account to be assigned
to the modem's ESN (electronic serial number). The ESN is printed on
modem's label
2. Wiring and power-up
1. Connect the modem to your computer using a standard Ethernet
cable. Alternatively, the RS-232 or USB ports can be used for
setup.
2. Connect the cellular antenna to the antenna connector.
3. Plug in the power connector to power-up the modem.
3. Start BlueVue Device Manager Software
BT-6600 BT6601 & BT-6601EB
BT-6621
LED State Description
Power ON Power is applied to the router
Signal
ON Excellent signal strength
FLASH Flashes faster as signal is stronger
OFF Very weak or no signal (less than -100dBm)
WAN
ON Wireless link established, but no data activity
FLASH Data transmitted/received on wireless network
RS232
ON Link established with serial device but no data activity
FLASH Data transmitted/received with attached serial device
GPS
ON Position fix available
OFF No position fix available
Ethernet
Link ON Link established with Ethernet device
Ethernet
Activity FLASH Data transmitted/received with attached Ethernet device
LABEL DESCRIPTION
GND Ground
PWR+ Power 8 to 30 VDC (12 or 24 VDC nominal)
IN Digital input
OUT Digital output
Speed: 115200 bps Data bits: 8
Parity: None Stop Bits: 1
Flow Control: Hardware

CONNECT. MONITOR. CONTROL. © 2014 Red Lion Controls. All Rights Reserved 2
Quick Start Guide
1. Download and install the latest version of BlueVue Device Man-
ager from www.redlion.net.
2. When launched, it will attempt to connect to 192.168.0.1 by
default, once connected to the modem, the Modem Diagnostic
window will open. (Note that 192.168.0.1 connects to the Ether-
net cable. To connect to the USB port use 192.168.111.1):
Troubleshooting: If BlueVue displays “Detecting Modem at
192.168.0.1” indefinitely, then:
• Make sure the modem is powered on.
• Check the Ethernet Link LED on the modem. If it’s off, it usually
means you have a problem with the Ethernet cable or with your
computer’s network card.
• Close all other network connections (such as WiFi)
• Set your computer to obtain an IP address automatically
4. Confirm that the modem is acquiring a cellular signal
The Signal LED should be on or flashing, indicating that the modem has
a signal. BlueVue Device Manager displays signal information in the top
right of its window; a minimum of 1 bar is required to connect to the
carrier with the modem.
Troubleshooting: If the Signal LED is off, then there may be an issue
with the antenna or cellular coverage might be too low in your current
location.
5. Activate the modem
This step programs the phone number and other SaskTel specific set-
tings into the modem so that it may be used on the SaskTel wireless
network.
1. Click on the ACT button located at the top and enter the following
information provided by SaskTel:
a. Master Lock Code: a 6-digit number
b. Phone number (MDN): a 10-digit number
c. MIN/MSID: a 10-digit number. If you were not provided with an
MIN/MSID, enter the MDN here.
d. Click on Submit and wait for activation to complete.
2. Click on the DIAG button located at the top left to navigate to the
Modem Diagnostic screen. Click on the Refresh button at the bot-
tom and check the phone number reported by the modem under
Modem Identification: it should match the MDN provided by Sask-
Tel.
Troubleshooting: If the above does not occur, then the modem most
likely has no account. Contact the wireless service provider who pro-
vided you with the account and ask them to confirm that the phone
number and MIN/MSID assigned correspond to the modem's ESN (elec-
tronic serial number), and that the account is ready to be used.
3. Confirm the modem has successfully connected to the cellular net-
work:
• The WAN LED will be on or flashing.
• In BlueVue, click the DIAG button, the WAN IP should indicate
the IP address assigned to the modem by the cellular network.
SETUP IS COMPLETE
The modem should be ready for use as a basic internet access point.
ADDITIONAL INFORMATION
For more advanced modem configuration, consult the support section
on our website. Visit our support page at www.redlion.net to access
the modem’s documentation, as well as configuration help, trouble-
shooting and firmware & software updates. Or contact Technical Sup-
port at 1-877-432-9908 or [email protected].
INSTALLATION AND HAZARDOUS AREA WARNINGS
Suitable for use in Class I, Division 2, Groups A, B, C and D hazardous locations,
or non-hazardous locations only. All power, input and output (I/O) wiring must
be in accordance with Class I, Division 2 wiring methods and in accordance with
the authority having jurisdiction.
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS
POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARD-
OUS.
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
AVERTISSEMENTS POUR INSTALLATION ET
ENDROITS DANGEREUX
Cet équipement est adapté pour une utilisation en Classe I, Division 2, Groupes
A, B, C et D pour endroits dangereux , ou endroits non-dangereux seulement.
Tout câblage électrique, entrée et sortie (I / O) doivent être en conformité avec
Classe I, Division 2 méthodes de câblage et conformément à l'autorité compé-
tente.
AVERTISSEMENT - RISQUE D'AVERTISSEMENT - NE DÉBRANCHEZ PAS L'ÉQUIPE-
MENT PENDANT QUE LE CIRCUIT EST DIRECT OU À MOINS QUE L'ENVI-
RONNEMENT SOIT CONNU POUR ÊTRE NON-DANGEREUX.
AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE TOUT COM-
POSANT PEUT NUIRE À LA CONFORMITÉ DE CLASSE I, DIVISION 2.