red lion MobilityPro BT-5600 Series User manual

CONNECT. MONITOR. CONTROL. © 2014 Red Lion Controls. All Rights Reserved 1
QUICK START GUIDE
MobilityProTM BT-5600 Series
Sprint Wireless Modem
OVERVIEW
The MobilityPro™ BT-5600 series modems are rugged 3G wireless
modems built to provide simple and reliable communication over the
EVDO Rev. A cellular data network.
This guide covers initial configuration for the BT-5600 & BT-5630.
FEATURES
•CDMA EVDO Rev. A with fallback to Rev. 0 a, 1XRTT and IS95
•Diversity antenna
•Ethernet, Serial, USB and WiFi (5630 model only)
•Reliable Always-on cellular link
•Rugged industrial design
•Remote diagnostics, configuration and updates
•3 Analog inputs, 4 Digital inputs, 3 Digital outputs
•IPsec VPN multiple tunnel and 3DES|AES up to 256-bit encryption
LED INDICATORS
ADDITIONAL INFORMATION
Visit our support page at www.redlion.net to access the modem’s docu-
mentation, as well as configuration help, troubleshooting and firmware
& software updates. Or contact Technical Support at 1-877-432-9908 or
[e-mail].
POWER
The modem has a 4-pin Molex connector for power input and requires
a power source between 8 and 30 VDC.
* An AC-DC power adaptor can be purchased as an accessory.
ANTENNA
An antenna with an SMA connector should be connected to the
modem. This antenna should meet the following specifications:
•Dual-band 800 & 1900 MHz
•Nominal 50 ohm impedance
•Voltage Standing Wave Radio (VSWR) less than 2.5:1
*Antennas are sold separately.
DATA INTERFACES
Ethernet: 10/100 Mbps Auto-sensing Female RJ45 port
USB: USB 2.0 Type B Female
Serial: RS-232 9 pin DCE Female, with these default settings:
•Speed: 115200 bps
•Data bits: 8
•Parity: None
•Stop Bits: 1
•Flow Control: Hardware
SETUP
1. Setup a data account for the modem
Contact your Sprint dealer and request a data account to be assigned to
the modem's ESN (electronic serial number). The ESN is printed on
modem's label.
2. Wiring and power-up
1. Connect the modem to your computer using a standard Ethernet
cable. Alternatively, the RS-232 or USB ports can be used for
setup.
2. Connect the cellular antenna to the antenna connector.
3. Plug in the power connector to power-up the modem.
3. Start BlueVue Device Manager Software
1. Download and install the latest version of BlueVue Device Man-
ager from www.redlion.net.
LED State Description
Power ON Power is applied to the router
Signal
ON Excellent signal strength
FLASH Flashes faster as signal is stronger
OFF Very weak or no signal (less than -100dBm)
WAN
ON Wireless link established, but no data activity
FLASH Data transmitted/received on wireless network
RS232
ON Link established with serial device but no data
activity
FLASH Data transmitted/received with attached serial
device
GPS
ON Position fix available
OFF No position fix available
Ethernet
Link ON Link established with Ethernet device
Ethernet
Activity FLASH Data transmitted/received with attached
Ethernet device
LABEL DESCRIPTION
GND Ground
POS Power 8 to 30 VDC (12 or 24 VDC nominal)
IGN Ignition sense
O3 Digital output

CONNECT. MONITOR. CONTROL. © 2014 Red Lion Controls. All Rights Reserved 2
Quick Start Guide
2. When launched, it will attempt to connect to 192.168.0.1 by
default, once connected to the modem, the Modem Diagnostic
window will open. (Note that 192.168.0.1 connects to the Ether-
net cable. To connect to the USB port use 192.168.111.1):
Troubleshooting: If BlueVue displays “Detecting Modem at
192.168.0.1” indefinitely, then:
•Make sure the modem is powered on.
•Check the Ethernet Link LED on the modem. If it’s off, it usually
means you have a problem with the Ethernet cable or with your
computer’s network card.
•Close all other network connections (such as WiFi)
•Set your computer to obtain an IP address automatically
4. Confirm that the modem is acquiring a cellular signal
The Signal LED should be on or flashing, indicating that the modem has
a signal. BlueVue Device Manager displays signal information in the top
right of its window; a minimum of 1 bar is required to connect to the
carrier with the modem.
Troubleshooting: If the Signal LED is off, then there may be an issue
with the antenna or cellular coverage might be too low in your current
location.
5. Activate the modem
This step programs the phone number and other Sprint specific settings
into the modem so that it may be used on the Sprint wireless network.
1. Click on the ACT button located at the top and enter the following
information provided by Sprint:
a. Master Lock Code: a 6-digit number
b. Phone number (MDN): a 10-digit number
c. MIN/MSID: a 10-digit number. If you were not provided with an
MIN/MSID, enter the MDN here.
d. Click on Submit and wait for activation to complete.
2. This step differs depending on what type of account you have:
a.If you purchased an IOTA account, then you will need to click on
Carrier Provisioning and then on click on IOTA to perform over-
the-air provisioning.
b.If you purchased an account with a Static IP address or a Dat-
alink account, then you will have to click on Carrier Provisioning
and then click on Datalink. You will then be required to enter
the credentials provided to you by Sprint and finally click on Sub-
mit.
Troubleshooting: If the above does not occur, then the modem most
likely has no account. Contact the wireless service provider who pro-
vided you with the account and ask them to confirm that the phone
number and MIN/MSID assigned correspond to the modem's ESN (elec-
tronic serial number), and that the account is ready to be used.
3. Confirm the modem has successfully connected to the cellular net-
work:
•The WAN LED will be on or flashing.
•In BlueVue, click the DIAG button, the WAN IP should indicate
the IP address assigned to the modem by the cellular network.
SETUP IS COMPLETE
The modem should be ready for use as a basic internet access point. For
more advanced modem configuration, consult the support section on
our website: www.redlion.net
INSTALLATION AND HAZARDOUS AREA WARNINGS
Suitable for use in Class I, Division 2, Groups A, B, C and D hazardous locations,
or non-hazardous locations only. All power, input and output (I/O) wiring must
be in accordance with Class I, Division 2 wiring methods and in accordance with
the authority having jurisdiction.
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS
POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARD-
OUS.
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
AVERTISSEMENTS POUR INSTALLATION ET
ENDROITS DANGEREUX
Cet équipement est adapté pour une utilisation en Classe I, Division 2, Groupes
A, B, C et D pour endroits dangereux , ou endroits non-dangereux seulement.
Tout câblage électrique, entrée et sortie (I / O) doivent être en conformité avec
Classe I, Division 2 méthodes de câblage et conformément à l'autorité compé-
tente.
AVERTISSEMENT - RISQUE D'AVERTISSEMENT - NE DÉBRANCHEZ PAS L'ÉQUIPE-
MENT PENDANT QUE LE CIRCUIT EST DIRECT OU À MOINS QUE L'ENVI-
RONNEMENT SOIT CONNU POUR ÊTRE NON-DANGEREUX.
AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE TOUT COM-
POSANT PEUT NUIRE À LA CONFORMITÉ DE CLASSE I, DIVISION 2.