Red Mountain Valley 2A-OC001 Owner's manual

47 In Fire Pit with BBQ Grate
Style # 2A-OC001,2A-OC002,2A-OC003,2A-OC137,2A-
OC138,2A-OC139
Assembly Instructions
& User’s Manual

Table of Contents
Page 1 of 10
Note: Before beginning assembly of product, make sure
all parts are present. Compare parts with package content
list and hardware contents. If any part is missing or
damaged do not attempt to assemble the unit. Contact
customer service for replacement parts.
Warnings………………………………………………………………..…2
Tools and Parts…………………………………………………………...5
Assembly Instructions…………………………………………………....6
Care and Maintenance……………………………………………...……9
Warranty Information………………………………………..................10

Warnings
Page 2 of 10
1.DO NOT use this fire pit without reading this entire document and all WARNINGS,
cautions and instructions.
2.This item is for outdoor use only, and shall NOT be used in a building, garage or any
other enclosed area
3.DO NOT use this fire pit for indoor heating. TOXIC carbon monoxide fumes can
accumulate and cause asphyxiation or death
4.This fire pit is NOT for commercial use.
5.This fire pit is NOT to be operated by children.
6.This fire pit is NOT to be used in or on boats or recreational vehicles.
7.Always use in accordance with all applicable local, state and national codes. Contact
your local fire department for details on outdoor burning.
8.When using this fire pit, exercise the same precautions you would with any open fire.
9.The use of alcohol, prescription or non-prescription drugs may impair the consumer’s
ability to properly assemble or safely operate this fire pit.
10.This fire pit is for use with dry, seasoned hardwood. It will burn hotter, more completely
and create less smoke.
11.DO NOT burn lump charcoal, manufactured logs, driftwood, trash, leaves, papers,
cardboard, plywood, painted or stained or pressure treated wood. Avoid using softwoods
such as pine or cedar that can throw sparks.
12.DO NOT alter this fire pit in any manner.
13.DO NOT use this fire pit until it is COMPLETELY assembled and all parts are securely
fastened and tightened.
14.DO NOT store or use gasoline or other flammable vapors or liquids in the vicinity of
this or any other appliance.
15.DO NOT store or use an LP gas cylinder within 10 feet (3.05 m) of this fire pit while it
is in operation. The fire pit should be placed no closer than 24 inch from walls during use.

16.DO NOT use this fire pit near automobiles, trucks, vans or recreational vehicles.
17.DO NOT use in an explosive atmosphere. Keep outdoor area clean and free from
combustible materials, gasoline and other flammable liquids.
18.DO NOT use this fire pit under an overhead or near any unprotected combustible
constructions.Avoid using near or under overhanging trees and shrubs.
19.Always use this fire pit on a hard level non-combustible surface such as concrete,
rock or stone.An asphalt or blacktop surface may not be acceptable for this purpose. DO
NOT use on wooden decks.
20.Always empty this fire pit before each use.
21.DO NOT wear flammable or loose clothing when operating this fire pit.
22.DO NOT use in windy conditions.
23.DO NOT use gasoline, kerosene, diesel fuel, lighter fluid to start or relight fires.
24.Keep all electrical cords away from a hot fire pit.
25.All surfaces of this fire pit are hot when in operation. To avoid burns, do NOT touch
fire pit until it has completely cooled unless you are wearing protective gear (potholders,
gloves, BBQ mittens, hot pads , etc). Never touch ashes to start or coals to see if they
are hot.
26.DO NOT leave a lit fire pit unattended, especially around children and pets.
27.DO NOT attempt to move or store this fire pit until ashes and coals are completely
extinguished.
28.DO NOT remove ashes or coals until they are completely and extinguished.
29.Use heat-resistant gloves or hot pads when contacting handles.
30.Use long, sturdy fire pit tools when adding or moving logs.
31.DO NOT place wood directly into bottom of the fire pit. Place wood only on the center
of the fire bowl.
32.DO NOT overload the fire pit. DO NOT add additional firewood until the fire burns
down. NOTICE: If any portion of the bowl of this fire pit are glowing red, it is overloaded.
33.DO NOT lean over this fire pit when lighting or when in use.
Page 3 of 10

34. DO NOT place hot pit tools onto combustible surface such as grass, wooden deck or
furniture.
35. Avoid breathing smoke from the fire and avoid getting it into your eyes.
36. This fire pit should be thoroughly inspected and cleaned on a regular basis.
37. After a period of storage and/or non-use, check for signs of damage and creosote build-
up.DO NOT operate until necessary repairs and/or clean up is executed.
38. Death, serious injury or damage to property may occur if the above is not followed
exactly.
Page 4 of 10

1 Phillips Head Screwdriver
2 Adjustable open end wrench
Tools Required
Parts List
Hardware
A Swing Handle 1
B Lift Handle 1
C1 Cooking Grate 1
C2 Cooking Grate Pole 1
D L-Pin 1
E Table Pane 4
F Fire Bowl 1
G1 Support Ring Section-A 4
G2 Support Ring Section-B 4
H Leg 4
J M6 x 14 Bolt 41
L M6 x 20 Bolt 8
M M6 Nut 10
N Wing Bolt 4
Page 5 of 10

Assembly Instructions
Step 1:
Attach (4) legs (H) to fire
bowl (F) with (12) M6 x 14
bolts (J)
Step 2:
Insert one support ring section
(G1) into （G2）and attach the
support ring assembly to leg (H)
with M6 x 14 Bolt（J）
(4) M6 x 14 bolts (J) as illustrated.
Repeat the same procedure to
install the other support ring
sections (G1+G2).
NOTE: Keep all bolts loose during
the assembly of this step until all
parts are installed into the correct
position.
Page 6 of 10

Assembly Instructions
Step 3:
Step 4:
Page 7 of 10
Secure (4) support ring
sections (G) with (4) M6 x
14 bolts (J).
Insert (2) the pins on table
panels (E) into the fixed
brackets on the fire bowl
(F) as illustrated .Connect
table panels (E) with (8) M6
x 20 bolts (L) and (8) M6
nuts (M).Attach (4) wing
nuts (N) to the fixed
brackets on the fire bowl
(F) as illustrated.
NOTE: The hole on the
table panel (E) should be
placed right upon the pole
on the fire bowl (F).

Assembly Instructions
Step 5:
Insert the Grate(C1) and
Pole(C2) were connected by
M6 x 14 Bolt(J)
Attach the lift handle (B) to
cooking grid(C) with (2)
M6*14bolts (J) as illustrated .
Attach the swing handle (A)
to cooking grid (C) with (2)
M6 x 14 (J) and (2) M6 nuts
(M) as illustrated.
Step 6:
Insert the cooking grid (C) post
into the table opening.
Insert L-pin (D) into the hole on
the cooking grid securing the
pole.
Page 8 of 10

Care and Maintenance
Page 9 of 10
Lighting
1. Make sure there is only a small amount of ash in the bottom of the bowl.
2. Place a layer of dry kindling or a natural fire-starter onto the center of the fire bowl.
3. Place above that a layer of dry seasoned hardwood that is no more than 3/4 the length of
the bowl diameter.
4. Use a match to light kindling or fire-starter.
Tending the Fire
You may need to shift and/or add logs for an ideal experience.
DO NOT place hot fire pit tools onto combustible surfaces such as grass, wooden deck or
furniture.
1. While using a long handled fire pit tool, shift coals and logs to allow additional airflow.
2. DO NOT add gasoline, kerosene, diesel fuel, lighter fluid or alcohol to relight or enhance
an existingfire.
3. Wait until glowing coals have developed before adding any additional wood. If additional
wood is required, place wood on top coals, be careful not to shift ashes.
Extinguishing
1. Allow fire to burn itself out.
2. DO NOT use water to extinguish as this is dangerous and can cause damage to this
outdoor fire pit.
Inspecting
This fire pit should be inspected on a regular basis to ensure product safety and longer
product life.
DO NOT attempt to inspect this fire pit until the fire is COMPLETELY out and cool to the
touch.
1. Check components for any signs of damage or rust.
2. If damage to any component is detected, do NOT operate until repairs are executed.
Cleaning
This fire pit should be cleaned on a regular basis to promote safer experiences and longer
product life.
Note: After repeated use, a slight discoloration of the finish may occur.
DO NOT attempt to clean this fire pit until the fire is COMPLETELY out and cool to the
touch.
DO NOT use oven cleaner or abrasive cleaners as they will damage this product.
DO NOT clean any part of this fire pit in a self cleaning oven as it may damage the finish.
1. Wipe exterior surfaces with a mild dishwashing detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.
3. Rinse and clean with water.
4. Remove built-up creosote from components with a chimney cleaning product.
Storage

Warranty Information
Page 10 of 10
This product has been manufactured under the highest
standards of quality and workmanship. We warrant to the
original consumer purchaser that all aspects of this product
will be free of defects in material and workmanship for one
year from the date of purchase. A replacement for any
defective part will be supplied free of charge for installation
by the consumer. Defects or damage caused by the use of
other than genuine parts are not covered by this warranty.
This warranty shall be effective from the date of purchase
as shown in the purchaser receipt.
This warranty is valid for the original consumer purchaser
only and excludes industrial, commercial or business use
of the product, product damage due to shipment or failure
which results from alteration, product abuse, or product
misuse, whether performed by a contractor , service
company , or consumer. We will not be responsible for
labor charges and/or damage incurred in installation, repair
or replacement nor for incidental or consequential damage.