RedLeaf RLC-BF2050 User manual

1

2
WELCOME
Thank you for purchasing our IP camera! This user’s
manual is designed to be a reference tool for your system.
Please read the following safeguards and warnings
carefully before you use this series product!
Please keep this user’s manual well for future reference!

3
IMPORTANT SAFEGUARDS AND WARNINGS
1. ELECTRICAL SAFETY
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra
Low Voltage) and the Limited power source is rated 12V DC in the IEC1-60950. We assume no
liability or responsibility for all the fires or electrical shock caused by improper handling or
installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2. TRANSPORTATION SECURITY
Heavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation.
3. INSTALLATION
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection. Always follow
the instruction guide the manufacturer recommended.
4. QUALIFIED ENGINEERS NEEDED
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair
5. ENVIROMENT
This series IP camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc. Please keep it away from the electromagnetic
radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera. Thunder-proof device is
recommended to be adapted to better prevent thunder.
The grounding holes of the product are recommended to be grounded to further enhance the
reliability of the camera.
6. DAILY MAINTENANCE
Please shut down the device and then unplug the power cable before you begin daily
maintenance work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on
the lens surface.

4
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water
to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to
clean the device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the
camera.
ACCESSORIES
1. ELEC TRICAL SAFETY
All installation and operation here should conform to your local electrical safety codes. The
power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC1 -60950.
Before you replace the SD card, please unplug the power cable and then remove the shell. We
assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation. We are not liable for any problems caused by unauthorized
modifications or attempted repairs.
2. INSTALLATION
Do not apply power to the IP camera before completing installation.
Do not put object on the IP camera.
3. ENVIROMENT
This series IP camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
The working temperature ranges from 10- to 60+. Please keep it away from the
electromagnetic radiation object and environment.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the RLC.
Thunder-proof device is recommended to be adopted to better prevent thunder. The grounding
studs of the product are recommended to be grounded to further enhance the reliability of the
camera.
4. DAILY MAINTENANCE
Current series RLC has no power button. Please unplug all corresponding power cables before
your installation.
Do not touch the CCD or CMOS part; you can use the blower to clean the dust on the surface of
the lens. You can use the dry cloth with some alcohol to clear if necessary.
Please keep the dustproof cap back to protect the CCD or CMOS part if the IP camera does not
work for a long time.

5
If there is too much dust on the housing, please use the water to dilute the mild detergent first
and then use it to clean the device with the clear dry cloth. Finally use the dry cloth to clean the
device.
5. ACCESSORIES
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.

6
1. GENERAL INTRODUCTION
1.1. Overview
This series IP camera integrates the traditional camera and network video technology. It
adopts audio and video data collection, transmission together. It can connect to the
network directly without any auxiliary device.
This series RLC uses standard H.264 video compression technology and MJPEG audio
compression technology, which maximally guarantee the audio and video quality.
This series RLC enclosure has the strong resistance capacity, which can guarantee the
proper work performance under heavy strike. It supports real-time monitor and motion
detect function. It can be used alone or used in a network area. When it is used lonely, you
can connect it to the network and then use a network client-end. Due to its multiple
functions and various uses, this series RLC is widely used in many environments such office,
bank, road monitor and etc.
1.2. Features

7
1.3. SPECIFICATIONS
1.3.1. Performance
Please refer to the following sheet for RLC performance specification.

8

9

10

11

12

13

14

15

16

17

18
2. FRAMEWORK
2.1. Rear Panel
This series IP camera real panel is shown as below. See Figure 2-1.
Please refer to the following sheet for detail information.

19

20