Edimax IC-3005Wn User manual

Internet Camera
Quick Installation Guide
The QIG will guide you through the basic setup of your product.
The detail instruction is stated in the user’s manual.

1
1. Check your package contents
One Internet Camera
One Power Adapter
One Camera Stand accessory kit
One 100cm Category 5 Ethernet Cable
One Quick Installation Guide
One CD (Including Manual/Utility/Driver)
If any of the above items are missing, please contact your supplier.
2. System Requirement
System requirement for PC, MAC or Notebook PC to access the Internet Camera are:
OS System: Windows 2000, XP + SP2, Server 2003, Vista32/64, Win7
CPU: Intel Pentium III 750MHz above or Intel Celeron 1GHz above
Memory Size: 128MB (256MB recommended)
VGA Card Resolution: 800 x 600 or above

2
3. Hardware Installation
3.1. LED and Focusing
The Camera head and its focus ring allow you to modify the aim and focus of the Camera.
To adjust the Camera’s focus, rotate the dark focus ring.
There are two LEDs indicating the camera status and networking status.
yGreen
Steady: System is ready
Blinking: System is booting.
yBlue
Steady: LAN is connected.
Blink: WLAN is activated.
Focusing
LENs
LED Green:
Status
LED Blue:
WLAN status
Antenna
(*Wireless Model Only)

3
3.2. Camera Ports
The Camera features two ports and a button.
Button: 1 click for WPS function(wireless model) or reset function or hold for more than 5 seconds
to reset the camera settings to factory default value.
Power Jack: Connect to power adapter for power supply with 5V DC.
LAN Jack: Connect to your local area network by network cable.
WPS
Reset to Default
Power Jack
With 5V DC LAN port
Stand hole

4
3.3. Installation Procedure
1. Unpack the Internet Camera package and verify that all the items listed in the Chapter 1 are
provided.
2. Connect the Internet Camera to your network by attached the network cable from the
switch/router to the LAN port of the Internet Camera.
3. Connect the power adapter to the Internet Camera and plug the power adapter to power outlet.
The Internet Camera will be powered on. When the Internet Camera is ready, the Green LED
will light.
Note: It is highly recommended to use the power adapter shipped with the Internet Camera, do
NOT use any other power adapter from any sources.

5
4. Software Installation
Follow the simple steps below to run the Install Wizard to guide you quickly through the Installation
process. The following installation is implemented in Windows XP. The installation procedures in
Windows 2000/XP/Server 2003/Vista/Win7 are similar.
1. Insert the CD shipped along with the Internet Camera into your CD-ROM drive. The
“Autorun.exe” program should be executed automatically. If not, run “Autorun.exe” manually
from “Autorun” folder in the CD.
2. The Install Wizard will show four selections, select the program you want to install or click “Exit”
to install the program later. The following installation steps are the demonstration of “Install
Administrator Utility” and ‘’Install 16 Chan Camera Viewer’’.

6
3. Click ‘’InstallAdministrator Utility’’ and when the following window appears, click ‘Next’.
4. You can specify the destination folder of software installation, you can just use the default folder,
and click ‘Next’ to continue.

7
5. If you need installation program to create a desktop icon or a quick launch icon for you, click all
items you need here, and click ‘Next’ to continue.
6. Here lists all options you chose in previous steps, if everything’s correct, click ‘Install’ to start
installing procedure, or click ‘Back’ to go back to previous step to modify installing settings.

8
7. The installing procedure will take some time, please be patient.
8. When you see this window, it means the software installing procedure is complete. Please click
‘Finish’ to finish the procedure (IP camera surveillance software will start after you click ‘Finish’
button, if you want to start it later, uncheck ‘Launch IP Cam Surveillance Software’ box).

9
9. After finished the installation of Administrator Utility, please go back to wizard page and click
‘’Install 16 Chan camera viewer’’, the system will start running viewer installation and the
procedures are similar to the installation of administration utility.
10. When the installation is completed. Please run ”Administrator Utility“. On the Internet Camera
first page, the cameras found in the network are listed. Choose the one you want to configure
and click “Setting Wizard” to proceed.