RedLeaf RLC-BF2420 User manual

port of the PC and then connect the earphone to the
audio output port of the device.
Login the Web and then click the Audio button to
enable the bidirectional talk function.
You can see the button becomes orange after you
enabled the audio talk function.
Click Audio button again to stop the bidirectional
talk function.
Please note the listening operation is null
during the bidirectional talk process.
Listening Operation
At the PC-end, speak via the speaker or the pickup,
and then you can get the audio from the earphone
or sound box at the device-end
1.3.3 Alarm Setup
Please follow the steps listed below for local alarm
input and output connection.
1) Connect the alarm input device to the alarm input
port (No.3 pin or No.4 pin) of the I/O cable.
2) Connect the alarm output device to the alarm
output port (No.2 pin) and alarm output public port
(No.1 pin). The alarm output port supports NO
(normal open) alarm device only.
3) Open the Web, go to the Figure. Please set the
alarm input 01 port for the first channel of the I/O
nd
cable (No.3 pin). The alarm input 02 is for the 2
channel of I/O cable (No.4 pin). Then you can select
the corresponding type (NO/NC.)
4) Set the WEB alarm output. The alarm output 01 is
for the alarm output port of the device. It is the No.2
pin of the I/O cable.
Please refer to figure 1-5 for alarm input
information.
Alarm input: When the input signal is idle or
2 Installation
2.1 Device Installation
Please follow the steps listed below to install the
device. Please refer to - Figure 2-1 for reference.
- Please draw the installation holes in the
installation surface and then mark
three expansion bolts holes in the
surface. Insert three bolts in the hole
and secure firmly.
- Please line up the installation holes of
the bottom of the pendant mount
bracket to the installation holes in the
surface. Then insert the three bolts to
the holes of the bottom of the bracket.
Finally fasten the device on the
installation surface.
2-2 SD Card Installation
Use the inner hex wrench from the installation
accessories bag to remove the four inner hex
screws from the rear cover. Please refer to -Figure
2-2 to find the SD card slot position. Insert the SD
card and the fix the four screws of the rear cover.
Important
- Please make sure the cable connection
between the power board and the main
board is firm. Otherwise, it may result in
device malfunction.
- The rear cover of the device adopts the
waterproof design. Please secure four
screws firmly after you complete the SD card
installation.
1.2 Framework and Dimension
Please refer to the following figure for dimension
information. The unit is mm. See -Figure 1-2 and
-Figure 1-3.
1.3 Bidirectional Talk
1.3.1 Device- end to PC-end Device Connection
Please connect the speaker or the MIC to the audio
input port of the device. Then connect the earphone
to the audio output port of the PC.
Login the Web and then click the Audio button to
enable the bidirectional talk function.
You can see the button becomes orange after you
enabled the audio talk function.
Click Audio button again to stop the bidirectional
talk function.
Listening Operation
At the device end, speak via the speaker or the
pickup, and then you can get the audio from the
earphone or sound box at the pc-end.
1.3.2 PC-end to the Device- end Device
Connection
Connect the speaker or the MIC to the audio input
Thank you for purchasing our IP camera.
This Quick Reference guide describes how to install
and configure your RedLeaf IP camera.
Before you start to install and use your new camera,
please read these instructions carefully. Please keep
this start guide well for future reference.
Please open the accessory bag to check the items
one by one in accordance with the list below. Contact
your local retailer ASAP if something is missing or
damaged in the bag.
For the most up-to-date information about this
product, visit the official RedLeaf website at
www.redleafsecurity.net
Please read these precaution notes before the
operation:
1．Electrical safety
All installation and operation here should conform to
your local electrical safety codes.
The power shall conform to the requirement in the
SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1.
Please note: Do not connect these two power
supplying sources to the device at the same
time; it may result in device damage!
We assume no liability or responsibility for all the fires
or electrical shock caused by improper handling or
installation.
We are not liable for any problems caused by
unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are
not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing
installation.
Please install the proper power cut-off device during
the installation connection.
Always follow the instruction guide the manufacturer
recommended.
4．Qualified engineers needed
All the examination and repair work should be done
by the qualified service engineers.
We are not liable for any problems caused by
unauthorized modifications or attempted repair.
5．Environment
This series IP camera should be installed in a cool,
dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from the electromagnetic
radiation object and environment.
Please make sure the CCD (CMOS) component is
out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical
component damage.
1.1 Multiple-function Combination Cable
You can refer to the following figure for multiple-function
combination cable information.
See -Figure 1-1.
Please refer to the following sheet for detailed
information.
Please refer to the following sheet for detailed I/O port information.
Welcome
Framework
Welcome
Installation
Framework Framework
....
....
..
..
..
..
M
MEGAPIXEL
8
....
....
..
..
..
..
M
MEGAPIXEL
5
1080
FULL HD
www.RedLeafSecurity.net
c 2012 Redleaf Corporation
Bullet Series
Version 1.1.0
Installation Manual
Before operating the unit
please read this manual
thoroughly and retain it for
future reference.
Network Camera
Accessory Name
RLC Unit
Quick Start Guide
12V to 24V Conversion Cable
(For AC 24V series product only)
Installation Location Map
CD Resource
Amount
1
1
1
1
1
DC 12V/AC
24V
Reset Reset
port
Power
input port
SN port Name Function Connection Note
-
-
-
I/O I/O port Connect to I/O port.
Hardware reset function.
Press it for 3 to 5 seconds;
system hardware can
restore default setup.
Power port. input DC 12V/AC
24V (Please use the provided
conversion cable)
Input audio signal. It can
receive the analog audio
signal from the pickup.
Output audio signal to the
devices such as the sound
box.
Connect to standard
Ethernet cable.
Output analog video signal.
It can connect to the TV
monitor to view the video.
LAN Network
port
Ethernet
port
AUDIO
IN
Audio
input
port
RCA
AUDIO
OUT
Audio
output
port
RCA
VIDEO
OUT BNC
Video
output
port
1
2
3
4
5
6
7
Port Name Name Note
ALARM_COM Alarm output public port.
Alarm output port. It is to
output the alarm signal to
the alarm device.
NO: normal open alarm
output port.
It works with the
ALARM_COM port.
Alarm input port 1. It is to
receive the on-off signal
from the external alarm
source.
Alarm input port 2. It is to
receive the on-off signal
from the external alarm
source.
Ground port
GND
ALARM_IN2
ALARM_IN1
ALARM_NO
I/O Port
Figure 1-1
Figure 1-4
Figure 1-6
!
!
Figure 1-5
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the
camera.
Thunder-proof device is recommended to be
adopted to better prevent thunder.
The gr o u n d i n g studs of th e product are
recommended to be grounded to further enhance the
reliability of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the
power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You
can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If
there is too much dust, please use the water to dilute
the mild detergent first and then use it to clean the
device. Finally use the dry cloth to clean the device.
Please put the dust proof cap to protect the CCD
(CMOS) component when you do not use the
camera.
7. Accessories
Be sure to use all the accessories recommended by
manufacturer.
Before installation, please open the package and
check all the components are included.
Contact your local retailer ASAP if something is
broken in your package.
Figure 2-1
Figure 1-3
Figure 1-2
102
81
307
105
grounded, the device can collect the different
statuses of the alarm input port. When the input
signal is connected to the 5V or is idle, the device
collects the logic “1”. When the input signal is
grounded, the device collects the logic “0”.
Please refer to figure 1-6 for alarm output
information.
Port A L A R M _ C O M and Port A L A R M _ N O
composes an on-off button to provide the alarm
output.
If the type is NO, this button is normal open. The
button becomes on when there is an alarm output.
If the type is NC, this button is normal off. The
button becomes off when there is an alarm output.

2- 3 Lens Adjustment
Turn counter clockwise to remove the lens cover,
now you can see the iris front and rear control rod.
The front control rod is to focus and the rear control
rod is to zoom. See - Figure 2-3. Please turn
clockwise to fix the lens cover back firmly.
Important
- Please remove the sunshield first and
remove the lens cover if you can not
unfasten the lens cover.
- The lens cover has the waterproof function.
Please make sure it is secure after you
complete the lens adjustment.
- HFW3202C series product has the default
motorized zoom lens. You do not need to
adjust manually.
2-4 Bracket Adjustment
You can use a M4 inner hex screw to control the
bracket. Please use the inner hex wrench from the
installation accessories bag to unfasten the screw.
See -Figure 24.The horizontal angle of the rear
cover can rotate 360°, the tilt angle can rotate 90°
and the chassis can rotate 360°.
Please use the inner hex wrench to secure the
screw firmly after you complete the setup.
Important
- Please make sure the M4 inner hex screw is
firm, otherwise it may result in chassis
vibration and the camera can not fix to a
specified angle.
O: Indicates that the concentration of the
hazardous substance in all
homogeneous materials in the parts is
below the relevant threshold of the
SJ/T11363-2006 standard.
X: Indicates that the concentration of the
hazardous substance of at least one of all
homogeneous materials in the parts is
above the relevant threshold of the
SJ/T11363-2006 standard. During the
envi r o n m e n t a l - f r i e n dly u s e p e r i o d
(EFUP) period, the toxic or hazardous
substance or elements contained in
products will not leak or mutate so that the
use of these (substances or elements) will
not result in any severe environmental
pollution, any bodily injury or damage to
any assets. The consumer is not
authorized to process such kind of
substances or elements, please return to
the corresponding local authorities to
p r oc e s s a c co r d i ng t o y o u r l o c a l
government statutes.
Note:
- This quick start guide is for reference
only. Slight difference may be found in
user interface.
- All the designs and software here are
subject to change without prior written
notice.
- All trademarks and registered trademarks
are the properties of their respective
owners.
- If there is any uncertainty or controversy,
please refer to the final explanation of
us.
- Please visit our website or contact your
lo c al ser v ice eng ineer fo r m ore
information.
Web Operation Web Operation
4 Web Operation
This series RLC product support the Web access
and management via PC.
Web includes several modules: monitor channel
preview, system configuration, alarm and etc.
4.1 Network Connection
Please follow the steps listed below for network
connection.
- Make sure the RLC has connected to the
network properly.
- RLC IP address and PC IP address shall be
in the same network segment. IPC default IP
address is 192.168.1.108. If there is router,
please set the corresponding gateway and
subnet mask.
- Use order ping ***.***.***.***(* IP camera
address) to check connection is OK or not.
4.2 Login and Logout
Open IE and input IP camera address in the
address bar.
For example, if your camera IP is 192.168.1.108,
then please input http:// 192.168.1.108 in IE
address bar. See - Figure 4-1.
The login interface is shown as below. See - Figure
4-2
Please input your user name and password.
Default factory name is admin and password is
admin.
Note:
For security reasons, please modify your
password after you first login.
If it is your first time to login in, system pops up
warning information to ask you whether install
control web rec. cab or not after you logged in for
one minute. Please click OK button, system can
automatically install the control. When system is
upgrading, it can overwrite the previous Web too.
If you can't download the ActiveX file, please check
whether you have installed the plug-in to disable
the control download. Or you can lower the IE
security level. See - Figure 4-3 and 4-4.
After you logged in, you can see the main window.
See -figure 4-5 .
Please refer to the Web Operation Manual included
in the resource CD for detailed operation
instruction.
Input your
address here
Select one IP address and then right click mouse
and change the IP address.
Note:
You can set the IP address, subnet mask and
gateway for the IPC and PC. Please note IPC IP
address and PC IP address shall be in the same
network segment if there is no router. IPC default
IP address is 192.168.1.108. If there is a router,
please set the corresponding gateway and subnet
mask.
The factory default user name is admin and
password is admin.
For security reasons, please mod if y your
password after you first login.
For detailed WEB operation, please refer to the
IPC Web Operation Manual in the resource CD.
Select the “Open Device Web” item; you can go to
the corresponding web login interface.
See - Figure 3-2.
If you want to modify the device IP address without
logging in the device web interface, you can go to
the configuration tool main interface to set.
In the configuration tool search interface , please
select a device IP address and then double click it
to open the login interface. Or you can select an IP
address and then click the Login button to go to the
login interface. See -Figure 3-3.
In -Figure 3-4, you can view device IP address, user
name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be
identical with the port value you set in TCP port in
Web Network interface. Otherwise, you can not
login the device.
If you are using device background upgrade port
3800 to login, other setups are all invalid.
After you logged in, the configuration tool main
interface is shown as below.See - figure 3-4
For detailed information and operation
instruction of the quick configuration tool,
please refer to the Quick Configuration Tool
User's Manual included in the resources CD.
3 Quick Configuration
3.1 Overview
Quick configuration tool can search current IP
address, modify IP address. At the same time, you
can use it to upgrade the device.
Please note the tool only applies to the IP
addresses in the same segment.
3.2 Operation
Double click the “ConfigTools.exe” icon, you can
see an interface is shown as in - Figure 3-1.
In the device list interface, you can view device IP
address, port number, subnet mask, default
gateway, MAC address and etc.
Quick Configuration Tool
Quick Configuration Tool
Component
Name
Circuit Board
Component
Case
Wire and Cable
Packing
Components
Accessories
Pb Hg Cd CrVI PBB PBDE
Toxic or Hazardous Materials or Elements
!
!
!
!
Figure 4-2
Figure 4-1
Figure 3-1
Figure 3-2
Figure 3-3
Figure 4-5
Figure 2-3
Figure 2-2
Installation
Figure 4-3
Figure 4-4