Reflexion CLR2610USB User manual

1
KITCHEN ALARM CLOCK WITH PLL FM RDS RADIO
-OWNER’SMANUAL -
MODEL NO. : CLR2610USB
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of un-insulated “dangerous voltage“ within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in theliterature accompanying the appliance.
WARNING :
TO REDUCE THE RISK OF FIRE OR ELECTIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
-DO NOT REMOVE EXTERNAL CASING TO EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS
ARE WITHIN.
-IF THE SUPPLY CORD IS DAMAGED, OR YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,
CONTACT AN AUTHORISED REPAIRER. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED.
-USE OF CONTROLS OR ADJUSTMENT OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS SITUATION.
-DO NOT INSTALL THIS EQUIPMENT IN A CONFINED SPACE, SUCH AS A BOOK CASE OR BUILT IN
CABINET.
-THIS EQUIPMENT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING.
The crossed out “Wheelie bin” is intended to show that this appliance must not be placed with ordinary
household waste.
When this appliance has reached the end of its useful life. It must be disposed of in
accordance with local by-laws. Consult our local waste disposal authority (WEEE Directive)

2
LOCATION OF CONTROLS
1. ALARM 2 / VOL –
2. ALARM 1 / VOL +
3. UP / NEXT
4. DOWN / PREV
5. POWER ON /OFF / USB (hold for Off)
6. MEMORY REVIEW / A.M.S.
7. ALARM MODE / TIMER
8. MEMORY SETTING
9. MODE SETTING
10. Preset key A/B/C/D/E/F
for USB operation:
D=PLAY, E=REP (repeat/ random), F=STOP
11. AOT (Auto Off Timer)
INSTALLATION
Unit speaker located at bottom case. To optimize for sound output, pls. refer below details for installation:
☆Mounting below the cupboard
1. Mark the location for 4 mounting screws
(not supplied).
2. Fix the unit holder on with 4 screws.
3. Insert unit in the holder.
☆Desktop setting
Mount the holder in the recesses on
bottom of unit
Note: To remove the unit, press snap-catch at the back and pull forwards.

3
POWER SOURCE
This unit is designed to operate on normal 230V ~ 50Hz household power source. Do not attempt to operate the
system using other power sources. This may result in damage to the unit and void your warranty.
Mains plug should be regularly checked. If it is found damaged, do not turn on the unit and must be replaced
before further use by a qualified service technician.
SET UP
Once the unit is powered up, date and clock defaulted to Friday, 1st Jan 2010. “PLEASE WAIT FOR SETTING
THANKS” scrolls on the display while time update takes place automatically. At this stage,
The two alarms are defaulted to 0:00 , daily type but disabled
The radio is switched off
It will switch to auto-run mode
☆Auto-run Mode (Radio OFF)
Press <MODE> once to go to different modes sequentially
Auto-run Mode Set the Clock Set the Date Set the SDA
(with Clock display) (Special Date Alert)
select 12/24 hour Dimmer ON/OFF Automatic update ON/OFF
In radio mode, if RDS information has been transmitted by the station, station name (instead of
frequency) will be displayed
Press <Alarm-1/Vol+> to review/set the alarm-1
Press <Alarm-2/Vol-> to review/set the alarm-2
When radio is ON, press <A, 0-9>, <B, 0-9>, <C, 0-9>, <D, 0-9>,<E, 0-9>, and <F, 0-9> to recall the
preset memories.
When the radio is ON, press <MEMORY SETTING>, <A-F> and then <MEMORY SETTING> again to
store the current station into memory.
When the radio is ON, press <ALARM1/Vol. +> and <ALARM2/Vol. -> to adjust speaker volume
When the radio is ON, press <MEMORY REVIEW /A.M.S> to preview those preset memory. Press
and hold for 2 seconds to activate the AMS (Automatic Memory Storage)
At every minute boundary, the real time clock is compared with the alarm setting if it has been
enabled. For details, please refer to the section of ‘When alarm is active
`
☆Setting the Clock (manually)
Press <MODE SETTING > once when the unit stays in clock display mode
The clock goes flashing the LCD with day-flag cleared
Press <UP> / < DOWN> to advance / move back the clock by 1 minute
Press and hold <UP> or <DOWN> to set the clock in fast mode of 10 minutes per step
Press <MODE SETTING > once to set the date.
Press other key to start its corresponding function.
If signal not given within 10 seconds, unit adopts current setting and switches to auto-run mode
☆Setting the Date
Press <MODE SETTING> once in clock setting mode
The current date goes flashing in the format of dd.mm.yyyy in the LCD
Press <UP> or <DOWN> to change the current setting by 1 day per step. Press and hold <UP> or
<DOWN> to change the setting in fast mode of 10 days per step. The day flag will be updated
automatically when the date has become steady.
Press <MODE SETTING > once to confirm the current setting and it switches to set the SDA.
Press other key to start its corresponding function.
If signal not given within 10 seconds, unit adopts current setting and switches to auto-run mode
automatically.

4
☆Setting the SDA (Special Date Alert)
Press <MODE SETTING> once in date setting mode
The date & ‘SDA’ goes flashing alternative
Press <UP> or <DOWN> to set the Special Date.
Press < TIMER/ALARM MODE > to ignore the year
Press <MODE SETTING > once to confirm current setting and go to set automatic update ON/OFF.
Press < A-F > to select the number of SDA
Press other key to start its corresponding function.
If signal not given within 10 seconds, unit adopts current setting and switches to auto-run mode
automatically.
In case of ignoring the year, the SDA will be active every year at same date
☆When SDA is active
When date/month/(year) matches with SDA which has been enable, alert becomes active at 8:00AM
As the SDA active, Sound of beep toggles at the Speaker for 10 minutes, Muted Radio even radio ON
& The “SDA” goes flash on LCD display
The beep will sound ever hour for 10 minutes until 23:00
Press any key to terminate the SDA when SDA is sounding.
☆Switching Automatic update ON/OFF
Press <MODE SETTING > once in SDA setting mode
The display show ‘UPDATE’ press <UP> or <DOWN> to switch update ON or OFF
The indicator “ ” disappears, the update function is switch OFF
The indicator “ ” flashes. The time will be updated the next RDS time signal is received.
Press <MODE SETTING> once to confirm the current setting and go to set the dimmer ON/OFF
Press other key to start its corresponding function.
If signal not given within 10 seconds, unit adopts current setting and switches to auto-run mode
automatically.
☆Switching Dimmer ON/OFF
Press <MODE SETTING > once in the automatic update setting mode
The display show ‘DIM ON’ or ‘DIM OFF’
Press <UP> or <DOWN> to switch dimmer ON or OFF
Display show ‘DIM ON’ the display is illuminated for 10 seconds, when any key had been pressed.
Display show ‘DIM OFF’ the display is illuminated for all time
Press <MODE SETTING> once to confirm the current setting and it switches to 12/24HOUR.
Press other key to start its corresponding function.
If signal not given within 10 seconds, unit adopts current setting and switches to auto-run mode
automatically.
☆Switching 12/24 hour
Press <MODE SETTING > once in Switching dimmer mode setting and it switches to select 12/24 hour.
The display show ’12 HOUR’ or ‘24 HOUR’
Press <UP> or <DOWN> to select 24 or 12.
Press <MODE SETTING> once to confirm the current setting and it switches to auto-run mode.
Press other key to start its corresponding function.
If signal not given within 10 seconds, unit adopts current setting and switches to auto-run mode
automatically.

5
BASIC OPERATION
☆Radio reception
Press <POWER> once, the station frequency or the station name show on LCD.
If RDS information is transmitted by the station current set, “ ” appears in the display and
after short time the station name appears in place of the frequency.
☆AMS (Automatic Memory System) Using
When radio is On, press and hold < MEMORY REVIEW/A.M.S > 2 seconds to active AMS mode. In
this mode, the radio will automatically store the station that had been scanned.
☆Search Up/Down
When the radio is ON, press <UP> once to change the receiving frequency up by 1 step (100KHz).
Press <DOWN> once to change the receiving frequency down by 1 step (100KHz).
Press and hold <UP> to search the next radio station by moving the receiving frequency up.
Press and hold <DOWN> to search the next radio station by moving the receiving frequency down.
☆Store into memory
To store the tuning frequency of radio station being received into any of the preset memory, press
<MEMORY SETTING > once. The ‘MEM’ goes flashing
Select desired memory station by pressing corresponding key until its number goes solid above ‘MEM’
Press < MEMORY SETTING > again to confirm the process of storing. Then, ‘MEM’ goes solid.
When ‘MEM’ is flashing, press < MEMORY REVIEW / AMS > will scan for stored memories
Press other key to start its corresponding function.
☆Recall radio preset memory
There are 60 preset memory stations for the radio
When the radio is ON, press <A,0-9> once. ‘MEM’ goes solid; the frequency of the memory-0 goes
solid in the LCD. Press <A,0-9> again and again to select the preset memory between 0~9.
Similar to <A,0-9>, press <B,0-9>, <C,0-9>, <D,0-9> , <E,0-9>or <F,0-9> to select the desired preset
memory station.
When new preset memory key is pressed, MUTE is active. When keying the preset memory has been
released for 1 second, the selection of preset memory is considered as valid and the radio will be
tuned to that frequency immediately with MUTE idle.
At any time, press other key to start its corresponding function.
☆Memory review
When the radio is ON, press <MEMORY REVIEW/A.M.S> once to scan the 10 preset memory stations
in folder A. Select folder B-F to review corresponding preset memory stations.
The review starts from the next memory station or A-0 if no memory station is being selected.
Review will stop at each station for 5 seconds.
During review, press other key will start its corresponding function and the review process will be
terminated.
☆USB MP3 Playback
Insert USB device, unit will search for all MP3 files and start playback automatically. LCD will show
current playing time.
Press <PLAY> again to pause; press <NEXT> or <PREV> for next or previous track and press
<STOP> to stop.
☆USB MP3 Repeat / Random Play
Unit defaulted at “Repeat-all” mode. Press <REP> to select “Random” or “Repeat-one”
Repeat All –display shows “ALL” and unit will repeat all MP3 files in the USB device
Random –display shows “RANDOM” while unit will random play the MP3 files.
Repeat One –display shows “ONE” while unit will only repeat current playing track

6
☆Setting the Cooking Timer (Radio OFF)
Press <TIMER/ALARM MODE > once to enter the timer mode.
Press <UP> or <DOWN> to adjust the value (from 1 minute to 23hours and 59minute) or press <A-F>
to recall the preset value, press <TIMER/ALARM MODE > to start the cooking timer.
When the timer is running press <TIMER/ALARM MODE> to pause the timer. To restart the timer
press <TIMER/ALARM MODE > again.
When the timer remain 30 seconds, the remind tone “be” will sound, (it also sound at 25s, 20s, 16s,
12s, 9s, 6s, 4s, 2s) the time reach to 00.00, the voice “be…be…be…be…be” will be heard forever.
Press <TIMER/ALARM MODE > to terminate the timer and exit.
Press and hold <TIMER/ALARM MODE > for 2 seconds to terminate the timer and leave, when the
timer is running.
As the alarm becomes active, the cooking timer, if exists, is terminated immediately.
☆Timer Preset (Radio OFF)
Press <TIMER/ALARM MODE> once to enter the timer mode.
Press <UP> or <DOWN> to adjust the value (from 1 minute to 23hours and 59minute).
Press <MEMORY SETTING > once, the ‘T’ goes flash. Press <A,0-9> ‘T1’ goes solid, press
<MEMORY SETING > again to store the timer-1 value.
Similar to <A,0-9>, press <B,0-9>, <C,0-9>, <D,0-9>,<E,0-9> or < F,0-9> to select the desired preset
timer value.
Press the <TIMER/ALARM MODE> to start the timer, press and hold <TIMER/ALARM MODE > for 2
seconds to exit the timer mode
☆Setting the Alarm (Radio OFF)
Press <ALARM1/VOL.+> or <ALARM2/VOL.-> once, ‘ALARM1’ or ‘ALARM2’ goes solid in the
alphanumeric section.
The current setting of HH:MM and the type of alarm go flashing by the corresponding day-flags.
Press <UP> to advance the setting by 1 minute
Press <DOWN> to move the setting back by 1 minute
Press and hold <UP> or <DOWN> to change the setting in fast mode of 10 minutes per step
Press <TIMER/ALARM MODE> to change the type of alarm between daily, weekday, weekend and
daily independently, which are reflected by the 7 day-flags
Press and hold <TIMER/ALARM MODE> to enter daily independently mode. Press <TIMER/ALARM
MODE> again to select the day and it will reflect by the day-flags. Press and hold <TIMER/ALARM
MODE> to leave the daily independently mode and return select daily, weekday and weekend.
Press same alarm key, which is <ALARM1/VOL.+> or <ALARM2/VOL.->, once to select the output
format of the alarm
Output format
LCD display
Beep sounds
‘Alarm’ symbol goes solid
Radio output
‘Radio’ symbol goes solid
Disable
All the ‘Alarm’ and ‘Radio’ are cleared
Press other key to start its corresponding function
When no key has been pressed for 10 seconds, the system goes back to auto-run mode
☆When alarm is active
When the real time clock matches with the alarm which has been enabled, alarm becomes active
As the alarm becomes active, the Cooking timer, if exists, is terminated immediately
If beep sounds alarm is selected,
a) Sound of beep toggles at the Speaker
b) Muted Radio even radio ON
c) The duration of alarm is 10 minutes

7
If Radio alarm is selected,
a) RADIO ON
b) the duration of the alarm is 60 minutes
To terminate the currently active alarm, press the corresponding key <ALARM1/VOL.+> or
<ALARM2/VOL.->.
☆AOT (Auto Off Timer) function
When radio is on, press the <AOT> key once, the LCD displays “AOT 90”. If radio is off, press <AOT>
will turn on the radio.
Press <AOT> once to change the time down by 5 minutes, press and hold <AOT> to change the
setting in fast mode.
When radio is on, and set the AOT time, press <AOT> once to change the time to the multiple of 5. For
example, the preset ATO time is 10, press once <AOT> to change time to 5, press again to OFF
90,85,80,…10,5,OFF…
When the time is reach to preset, it will turn off the radio automatically.
☆Electronic Volume Control (Radio ON)
Press <ALARM1/VOL +> once, to increase speaker volume by one step. Hold for continually.
Press <ALARM2/VOL -> once, to decrease speaker volume by one step. Hold for continually.
☆Key-lock
Press and hold <MEMORY SETTING> for 2 seconds, key-lock has been switched ON; the word “KEY”
goes solid.
Press and hold <MEMORY SETTING> again for 2 seconds to release key-lock; the word “KEY” will
disappear.
SPECIFICATION
Power supply: AC 230V ~ 50Hz
Power consumption: 7W
Standby consumption: 1.36W
Battery backup: 2 x AAA (LR03) 1.5V (not included)
Radio section: FM 87.5 –108 MHz
Audio output: 1.8 W
Dimension:
with stand: (B) x (T) x (H) 275 x 156 x 94MM
Mounting under cupboard: (B) x (T) x (H) 275 x 156 x 64MM
Gross weight: 1.0 kg