Regal Rexnord UVANTAGE PLUS User manual

installation manual

2| UVantage PLUS™ Installation Guide
Input Voltage: 81104278/ UVLED-R: 100 - 240VAC
81104280/ UVLED-C: 120 - 277VAC
Rated Input Frequency: 50/60Hz
Rated Current: 1.6A Max
Output Voltage: 24 VDC
Power Consumption: AC input power up to 43W
Lamp Type: UVC LEDs
UVC Wavelength: 275 ± 5 nm
Reliability (hrs.): 33,000 hrs @ 25°C ambient, 100 mA
Operating Conditions: Temp Range: 10°C to 60°C
Note: Reduced efficacy could occur above 40° C
RH Level: 10% to 95% RH
Regulatory Standards: UVC LEDs: UL – CCN ABQK, UL 2998, EPA Compliant
Safety: UL/ cUL, FCC Part 15 Class B
specifications

Visit UVantage.com for additional information | 3
preferred
mounting locations
6”
Suggested
Location
Optional
Location
RETURN
AIR DUCT
SUPPLY
AIR DUCT
For Flex duct, duct board, drywall applications, proposed option of mounting
the device at the apex of the evaporator coil

4| UVantage PLUS™ Installation Guide
safety GUIDELINES
AUVC LEDs cause potential eye injury.
DO NOT attempt to install the device
while connecting the power supply to
the UVantage PLUS
™
device.
ADO NOT expose naked skin to UVC
directly and DO NOT look at the UVC
LEDs with naked eyes. UVC radiation is
NOT visible to humans. Wavelength is
between 200 and 280 nanometers.
AKeep out of reach of CHILDREN.
ADO NOT touch UVC LEDs with bare
hands.
ADisconnect the DC jack before
servicing the UVantage PLUS™device.
AOnly use the supplied power adapter to
turn on the device.
AWARNING indicates a hazard which,
if not avoided, could result in serious injury
or death.
AWARNING
ACAUTION indicates a hazard which,
if not avoided, could result in minor or
moderate personal injury.
ACAUTION

Visit UVantage.com for additional information | 5
Items Included for
Installation
Control Cover Qty 1
Duct Plate Qty 1
LED Module Qty 1
Lead Assembly Qty 1
Screw Qty 4
Power Supply Qty 1
Template Qty 1
Gasket Qty 1

6| UVantage PLUS™ Installation Guide
DO’s
✓Disconnect all power supplies to the
HVAC unit and UVantage PLUS™ module
(hereafter referred to as “LED module”)
before beginning any servicing.
✓Install the LED module at one of the
preferred locations listed by the
manufacturer in this manual.
✓Use the power supply which was
provided with the LED module for safe
operation.
✓Use gloves and safety goggles while
installing the LED module.
✓Understand all the safety guidelines of
UVC radiation before handling the LED
module. Refer to the Safety Guidelines in
this manual.
✓While installing the UVC product, maintain
a minimum distance of 6 feet clearance
from filter or plastic materials which are
in direct line of sight. If not in direct line
of sight, a minimum distance of 3 feet is
recommended.
DON’Ts
✗Don’t attempt to look at the
UVC LED module while in
operation.
✗Don’t allow any UV light to
escape from ductwork in
any way. Make sure ducts
are sealed.
✗Don’t touch the UVC LEDs
directly with bare oil from
hands may damage the bulb.
✗Don’t operate the LED
module when the product
reaches the end of lifespan.
A RED LED will be displayed
on the control cover.
✗Don’t rotate the LED module
clockwise while installing.
✗Don’t connect power to the
module before completing
the entire installation.
installation

Visit UVantage.com for additional information | 7
installation
1. Use template to mark the cut-pattern on
the duct surface. It is suggested to align
the template centered in the ductwork.
2. Use a hole saw to make a 1.25-inch
hole on the duct surface.
Ensure there is enough duct
depth (minimum 14 inches)
before proceeding with the
installation.
A

8| UVantage PLUS™ Installation Guide
installation
3. Install the wall plate to the duct
surface along with the gasket using
the 4 self-threaded screws where
actual template mark was drawn.
Recommended mounting torque for
the screws is 0.4 ~ 0.5 N-m
The direction of the mounting should
match the airflow direction in the
ductwork as per the marking given on
the wall plate.

Visit UVantage.com for additional information | 9
installation
4. Connect the wire harness to the LED
module and insert the LED module
through the hole of the wall plate and
rotate it counter-clockwise to lock the
LED module.
Don’t touch UVC LEDs
with bare hand.
Don’t rotate the module
clockwise; else it will result
in causing damage to the LED
module.
A
A

10 | UVantage PLUS™ Installation Guide
installation
5. Connect the LED module harness
to the control cover as shown in
the image.
6. Snap the control cover firmly to the
wall plate.
SAFETY
SWITCH

Visit UVantage.com for additional information | 11
installation
INDICATION CAUSE
GREEN LED Unit ON
PURPLE LED UVC LEDS ON
GREEN LED
(flash once) Voltage fluctuations
GREEN LED
(flash twice) Current fluctuations
PURPLE LED
(flashing) SAFETY SWITCH malfunction
RED LED
(flash once)
UVC LEDS life span reached 80%
(Plan for part replacement)
RED LED
(flash twice)
UVC LEDS life span reached 90%
(Request part replacement from supplier)
RED LED UVC LEDS reached end of life span
(Replacement is needed)
Note: Refer to the troubleshooting section page for more details.
7. Connect the 24V adapter plug
to the DC jack on the control
cover and plug the power
supply into an outlet or control
wiring depending on the
application requirements.
Display Indications on the device
GREEN: Control Unit power ON
PURPLE: UVC LEDs module ON
RED: Unit Faulty
Hardwired Power
Supply (UVLED-C)
Wall Plugin Power
Supply (UVLED-R)
Green LED
Red/Purple LED

12 | UVantage PLUS™ Installation Guide
troubleshooting
LED
Indicator Status Condition Troubleshooting
Green
LED
ON Unit ON No action required.
OFF Unit OFF / Power
Failure
1. Verify the system is receiving proper line
voltage.
2. If the line voltage reading is good, check
for any loose connections of the power
supply adapter.
3. If the above steps do not work, contact the
service provider for unit replacement.
SINGLE
FLASH
Over / Under Voltage
Error
1. Verify the system is receiving proper line
voltage, If the line voltage reading is good
proceed with the next step.
2. Use only adapter provided with Uvantage
PLUS
™
unit.
3. If the above steps do not work, contact the
service provider for unit replacement.
DOUBLE
FLASH
Over / Under Current
Error
1. Check for any loose connections of the UVC
LED module.
2. If the above steps do not work, contact the
service provider for unit replacement.
Purple
LED
ON Disinfection ON No action required.
OFF Disinfection OFF /
Halted
1. Check if there is no airflow in the duct. UVC
LED turns ON only in the presence of airflow
inside the duct.
2. If the UVC LED doesn’t turn on in the
presence of airflow, the UVC LED module
needs to be replaced.

Visit UVantage.com for additional information | 13
troubleshooting
Red
LED
OFF No UVC Replacement
Notification No action required.
ON
100% UVC LED
Life consumed.
(The UVC LED life
has reached its end
and replacement
is mandatory and
disinfection is halted)
Turn off the Uvantage PLUS™unit and consult
supplier for the unit replacement.
SINGLE
FLASH
80% UVC LED
Life consumed.
(UVC LEDs life reached
80% of its lifetime.)
Plan for the UVantage PLUS™replacement.
DOUBLE
FLASH
90% UVC LED
Life consumed.
(UVC LEDs life reached
90% of its lifetime.)
Contact supplier to schedule the replacement.
LED
Indicator Status Condition Troubleshooting
Purple
LED FLASH Safety Switch Error
1. Verify the Control unit is mounted properly
without any loose fittings on the duct wall, so
that safety switch holds with wall plate firmly.
2. If the above steps do not work, contact the
service provider for unit replacement.

14 | UVantage PLUS™ Installation Guide
faq’s
1. What is UVC?
UVC refers to an ultraviolet light with a wavelength between 200-280 nm. The light in this
wavelength can be used for germicidal irradiation in a HVAC system.
2. Where should the UVantage PLUS™ product be installed in the HVAC system?
The UVantage PLUS
™
device can be installed safely in all the duct works as highlighted in
preferred location for both residential and commercial HVAC systems.
3. Is the UVantage PLUS™ product effective in deactivating bacteria/viruses?
Yes, UVantage PLUS
™
device sterilizes airborne bacteria and viruses up to 99.99%
(4 net log reduction). For further information, please see Page 15 of this manual.
4. How often do we need to clean the UVantage PLUS™ device?
Avoid direct cleaning of the UVC LEDs. UVC LED membranes are sensitive towards human
touch or brushes which might damage them and impact their operation. Should you need to
clean the device, it is advised to simply blow over the LED module.
5. Do UVC LEDs replace filters which are already being used in the duct?
No. The UVantage PLUS
™
device is not intended to replace filters. This product, when used
in conjunction with duct filters, provides an additional layer of protection to reduce airborne
contaminants.
6. Is UVC harmful?
UVC is harmful to all organic matter including human beings. Direct exposure may cause eye
or skin injuries and prolonged exposure may also lead to serious skin concerns. To operate
the UVantage PLUS
™
device safely, it is highly recommended to follow the safety guidelines
provided in this manual.
7. Does the UVantage PLUS™ device generate ozone?
No, the UVantage PLUS
™
device is completely ozone free and is compliant to UL 2998 standard.

Visit UVantage.com for additional information | 15
TESTED AND
EFFECTIVE
Testing conducted by Aerosol Research and Engineering Laboratories, Inc., an independent
GLP-compliant lab, indicate UVantage PLUS
™
was effective at reducing 99.99% of T1 and
MS2 bacteriophages from room air when used as directed. These species are recognized
surrogates: T1, a non-enveloped double-stranded DNA virus, is a common surrogate human
pathogens like Cryptosporidium and MS2, a single-stranded RNA virus, is routinely used as
a surrogate for pathogenic RNA viruses such as Influenza and also serves as a tentative
surrogate for SARS-CoV-2.

16 | UVantage PLUS™ Installation Guide
Regal Rexnord Corporation, Climate Solutions
1946 W. Cook Road, Fort Wayne, IN 46818
Support 1-800-252-1182
5yr
LIMITED
WARRANTY
Scan QR Code
Learn more or watch the
installation video
Warning: UVC radiation can cause severe burns (of the skin) and eye injuries
(photokeratitis). Avoid direct skin exposure to UVC radiation and never look directly into a
UVC light source, even briefly.
Regal Rexnord and UVantage PLUS are trademarks of Regal Rexnord Corporation or one of
its affiliated companies. Regal Rexnord Corporation, Climate Solutions 1946 W. Cook Road,
Fort Wayne, IN 46818, United States Designed by Regal Rexnord Corporation.
Patent Pending