Regency City Series San Franciso Bay 50 User manual

Regency City Series San Franciso Bay 50
CB50E-NG / CB50E-LP
FRAMING
DIMENSIONS
SPECIFICATIONS
HEAT RELEASE REQUIREMENTS
QR LINK FOR
PDF DIGITAL COPY
OF SPECIFICATIONS:
MUST READ BEFORE
FRAMING
IMPORTANT INFORMATION

City Series CB50E | 7
dimensions
13 3
8
"
340mm
18"
457mm
10 3
16
"
259mm
60"
1524mm
61 1
16
"
1551mm
11 5
16
"
288mm
9 1
8
"
231mm
11 5
16
"
288mm
48 11
16
"
1236mm
5"
127mm
8"
203mm
37"
940mm
20 7
16
"
519mm
20 15
16
"
532mm
13 7
16
"
341mm
18"
457mm
10 1
8
"
258mm
60"
1524mm
61 1
16
"
1551mm
11 5
16
"
288mm
9 1
8
"
231mm
11 5
16
"
288mm
48 11
16
"
1236mm
5"
127mm
8"
203mm
37"
940mm
20 7
16
"
519mm
20 15
16
"
532mm
10 1
8
"
257mm
4 7
16
"
112mm
16 5
8
"
423mm
Dimensions - Bay Install
Note: Height Dimension is taken with leveling legs fully inserted and may vary depending on the height of the leveling
legs, when unscrewed or extended.
Dimensions will appear as (inches)" / (metric) mm
throughout this manual. The inches are rounded to
the nearest 1/16" when converted, when greater
accuracy is required, use the metric dimensions.
Note: These units are non-load bearing.
ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.
ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

8 | City Series CB50E
installation
Gas Connection - Bottom of Unit
Gas Connection - Side of Unit
16 3
8
"
OPENING AT UNIT BASE
20"
7 1
8
"
11 3
8
"
GAS VALVE
FRONT OF UNIT
BACK OF UNIT

City Series CB50E | 9
installation
Electrical Connection - Bottom of Unit
Electrical Connection - Side of Unit

10 | City Series CB50E
dimensions
13 7
16
"
341mm
18"
457mm
10 1
8
"
258mm
60"
1524mm
61 1
16
"
1551mm
11 5
16
"
288mm
9 1
8
"
231mm
11 5
16
"
288mm
48 11
16
"
1236mm
5"
127mm
8"
203mm
37"
940mm
20 7
16
"
519mm
20 15
16
"
532mm
16 1
2
"
419mm
3 15
16
"
101mm
Dimensions - Corner Install
Note: Height Dimension is taken with leveling legs fully inserted and may vary depending on the height of the leveling legs, when unscrewed or extended.
Dimensions will appear as (inches)" / (metric) mm
throughout this manual. The inches are rounded to the
nearest 1/16" when converted, when greater accuracy
is required, use the metric dimensions.
Note: These units are non-load bearing.
ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.
ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

City Series CB50E | 35
installation
Ventilation Openings (Three-sided/Bay Installation)
Regency's patented Cool Wall system releases warmth at ceiling level. This
system reduces excessive radiant heat in front of the replace so you can
enjoy your replace more often.
• Design your own chase vent solution to suit your home
• Use optional front or left & right side chase vent grills
• Release warmth into the room discreetly
Front Exit
The ventilation opening may be placed in front ensuring it meets the 152
square inch opening & is located 0-2" (51mm) from the enclosure ceiling.
Side Exit (Left/Right)
Ventilation openings, when placed on both sides, must be of the same size.
They must be have an equal split (50/50) free air opening to balance air ow.
A ventilation opening may never be on one side only.
The ventilation openings cannot be any smaller than 6" (152mm) wide to
equal the total area of 152 square inches of free open area.
Example: 6" (152mm) wide x 15" (381mm) High = 90 square inches per side
of free open area. A second ventilation grill is installed on the other side to
=100%.
The ventilation openings must be located 0-2" (51mm) from the enclosure
ceiling.
Top Exit
The ventilation opening may be short of the ceiling as shown below.
Minimum opening height must be 1-3/4" (44mm) measured from top of
enclosure to the ceiling and must be in open in front and both sides to
meet the minimum 152 square inches free open air requirement.
Ventilation Opening Locations
The following are examples of how the ventilation openings may be placed
above the replace.
If using the optional heat wave kit, this does not reduce the size of the
ventilation opening. The ventilation opening(s) must be a minimum 152
square inches regardless.
The air travelling through the heat exchanger is heated by the replace and
then directed out the back of the replace. The combined warmed air is then
vented back into the room.
The ventilation opening may be fully open at the top of the enclosure.
This type of ventilation opening would be used when the top of the
enclosure is not visible from above and where the ceiling within the
room is higher than normal. When creating this type of ventilation
opening, measures should be into place to avoid having objects of any
type falling or be thrown into the ventilation opening. Mesh screen or
other preventative measures should be put into place.
The ventilation opening may be placed on top ensuring it meets the 152
square inch opening. This type of ventilation opening would be used
when the top of the enclosure is visible from above and where the
ceiling within the room is higher than normal.
NOTE
For right/left two-sided corner, see next page.

36 | City Series CB50E
installation
Ventilation Openings (Right/Left Corner)
Regency's patented Cool Wall system releases warmth at ceiling level. This
system reduces excessive radiant heat in front of the replace so you can
enjoy your replace more often.
• Design your own chase vent solution to suit your home
• Use optional front or left & right side chase vent grills
• Release warmth into the room discreetly
Front Exit
The ventilation opening may be placed in front ensuring it meets the 152
square inch opening & is located 0-2" (51 mm) from the enclosure ceiling.
Side/Front Exit
Ventilation openings, when placed on the side, must also have the same size
ventilation opening in front. They must be have an equal split (50/50) free
air opening to balance air ow. A ventilation opening may never be on one
side only.
The side ventilation opening cannot be any smaller than 6" (152mm) wide to
equal the total area of 152 square inches of free open area.
Example: 6" (152mm) wide x 15" (381 mm) High = 90 square inches of free
open area. A second ventilation grill is installed in front to =100%.
The ventilation openings must be located 0-2" (51 mm) from the enclosure
ceiling.
Top Exit
The ventilation opening may be short of the ceiling as shown below.
Minimum width/depth of chase x height measured from top of enclosure
to the ceiling and must be in open in front and side to meet the minimum
152 square inches free open air requirement.
Ventilation Opening Locations
The following are examples of how the ventilation openings may be placed
above the replace.
If using the optional heat wave kit, this does not reduce the size of the
ventilation opening. The ventilation opening(s) must be a minimum 152
square inches regardless.
The air travelling through the heat exchanger is heated by the replace and
then directed out the back of the replace. The combined warmed air is then
vented back into the room.
The ventilation opening may be fully open at the top of the enclosure.
This type of ventilation opening would be used when the top of the
enclosure is not visible from above and where the ceiling within the
room is higher than normal. When creating this type of ventilation
opening, measures should be into place to avoid having objects of any
type falling or be thrown into the ventilation opening. Mesh screen or
other preventative measures should be put into place.
The ventilation opening may be placed on top ensuring it meets the 152
square inch opening. This type of ventilation opening would be used
when the top of the enclosure is visible from above and where the
ceiling within the room is higher than normal.

City Series CB50E | 37
installation
Chase Enclosure
Max 3”
(76 mm)
Ceiling Ceiling
Top of chase enclosure
Max 3”
(76 mm)
Stud
Stud
Stud
Stud
40” (1016 mm) Chase Vent
C40 Chase Vent Framing Clearances
Opening for vent
4”-4.5”
(102 mm x 114 mm)
Min 42.25” (1073 mm)
Framed opening must be between 4” (102 mm) and 4.5” (114 mm) tall, and at least 42.25”(1073 mm) wide
to accommodate the chase vent. The top of the chase vent opening must be 3” or less from the top of the
chase enclosure.
40” (1016 mm) Chase Vent
Top of chase enclosure
In the example above, the ceiling does not
meet the requirement as it is higher than
the specied minimum.
Top of chase enclosure is sealed o to
meet the 0-2'' (51mm) requirement.
Top of chase enclosure
Minimum 152sq. inch opening
Minimum 152sq. inch opening
When choosing to install the ventilation openings from the front or both sides, The top of the ventilation opening cannot be any lower than 0-2" (51mm)
from the top of the chase enclosure for all installations.
Minimum height of enclosure from base of appliance is 62-7/8" (1597 mm).
A minimum 152in2opening in the enclosure is required to maintain safe operating temperatures. This can be achieved in a number of ways including the
examples shown in this manual.
IMPORTANT:
Exterior wall/Alcove enclosure: When installing into an exterior cavity or alcove enclosure (ceiling, back and sides), regardless of where appliance is
placed within the home, requires the use of either drywall or other means such as plywood, wood studs, etc. to prevent heat from escaping anywhere above
/through the enclosure other than the required grill / ventilation opening.
Internal chase: When installing as an internal chase framing installation ,regardless of where appliance is placed within the home, requires the use of either
drywall or other means such as plywood, on the rear wall of the chase to eliminate heat escaping into the rear wall cavity. If the chase is extended to the
ceiling ,the ceiling will also need to be nished in a manner to prevent heat escaping into oor joist/attic space.
One of the following methods must be used to prevent the heat from escaping.
a. If choosing drywall, ensure that the drywall is butt up tight with no gaps.
b. Plywood, wood studs, etc. installed tightly with no gaps.
As this appliance has been designed with all hot air escaping through the chase enclosure ventilation/grill openings only, if hot air is trapped as a result of
the hot air escaping through joints, crevasses, open studs, or other openings within the enclosure above, this will change the clearances within the enclosure
causing the enclosure to overheat. It is vital that all the hot air from within the enclosure exits through the ventilation openings only.
Ensure that the ventilation openings are made as such to prevent debris, objects from falling into the enclosure.
Warning: DO NOT cover or place objects in front of the ventilation opening air outlet(s).
Max. 2''
(51mm)
Max. 2''
(51mm)

38 | City Series CB50E
installation
Clearances (3-sided)
The clearances listed below are minimum distances unless otherwise stated.
A major cause of chimney related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that
this replace and vent system be installed only in accordance with these instructions.
Flue Clearances to Combustibles
Horizontal - Top 3" (76 mm)
Horizontal - Side 2" (51 mm)
Horizontal - Bottom 2" (51 mm)
Vertical 2" (51 mm)
Passing through wall/
floor/ceiling - when
restop is used.
1-1/2" (38 mm)
Note: This appliance uses 5" x 8" venting for
the Non Power Vent.
F
E
B
Alcove
Clearance Dimension Measured From:
A1: Mantel Height (min.) ** Top of Fireplace Opening
A: From Floor (min.) 10-3/16" (462 mm) Bottom of Fireplace Opening
B: Sidewall (on one side) min. 5" (127 mm) Side of Fireplace Opening
C: Enclosure Width (min.) 60'' (1524 mm) Minimum inside dimensions
D: Mantel Depth (max.) **
E: Alcove Width 92" (2337 mm) Sidewall to Sidewall (Minimum)
F: Alcove Depth 35" (889 mm) Front to Unit (Maximum)
G: Convection Air Outlet Opening Oset
(min.) 2" (51 mm) Max. oset from top of chase enclosure
H: Convection Air Outlet 152 in2(981 cm2)
I Enclosure Depth (min.) 20-7/16" (519 mm) Minimum inside dimensions
J: Opening Height 18" (457mm) Bottom/Top of Fireplace Opening
K: To Ceiling (min.) all 3 sides 1-3/4" (44mm) To Top of Ceiling
L: Chase Enclosure (min.) 62-7/8" (1597 mm) From base of unit/oor to top of enclosure
M:Clearance to Sprinkler Head (min.) 36" (914mm) Perpendicular from chase grill
Hearth 0" No hearth required
Ceiling Height 81-1/4" (2064 mm) From base of unit /oor to top of alcove
** See mantel clearances chart in the manual.
Caution Requirements
The top, back and sides of the replace are dened by
standos. The metal ends of the stando may NOT be
recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are
not adhered to. It is of greatest importance that this replace
and vent system be installed only in accordance with these
instructions.
When installed as a power vent, the venting
must be reduced to 4" inner x 6-5/8" outer
(102 mm x 168 mm) in all applications. See
reducers required in this manual if using rigid/
ex pipe.
L
Chase grill
Sprinkler
Side view
M

City Series CB50E | 39
installation
Clearances
Floor to ceiling with top opening Full framing with vents in front/2 sides or top
Full framing with low vents in front or 2 sides Full framing with vents in front or 2 sides
C
I
A1
A
D
LJ
H
L
I
C
D
A1
A
J
G
G
H
H
H
I
C
G
A
A1
G
D
J
L
H
H
I
A
D
C
J
GG
L
H
H
A1
opening opening
opening opening

40 | City Series CB50E
installation
Caution Requirements
The top, back and sides of the replace are dened by
standos. The metal ends of the stando may NOT be
recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not
adhered to. It is of greatest importance that this replace and vent
system be installed only in accordance with these instructions.
Clearances - Corner Install
The clearances listed below are minimum distances unless otherwise stated.
A major cause of chimney related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that
this replace and vent system be installed only in accordance with these instructions.
Note: Left handed corner shown in illustration. Clearances will be the same for the right hand side.
Clearance: single sided Dimension Measured From:
A: Mantel Height (min.) ** Top of Fireplace Opening
B: Opening Height 18" (457 mm) Bottom/Top of Fireplace Opening
C: From Floor (min.) 10-3/16" (462 mm) Bottom of Fireplace Opening
D: Sidewall (on one side) min. 37" (940 mm) Side of Fireplace Opening
E: Mantel Depth (max.) ** Front of Fireplace Opening
F: Alcove Depth 35" (889 mm) Front of Fireplace Opening
G: Convection Air Outlet 152 square inches
(981 cm2)
H: Convection Air Outlet Opening Oset 2" (51 mm) Max. oset from top of chase enclosure
I: Chase Enclosure (Min.) 62-7/8" (1597 mm) From Base of Unit/Floor to top of enclosure
J: Convection Air Outlet Opening Oset
(min.) 2" (50mm) To top of ceiling
Ceiling Height 81-1/4" (2064 mm) From base of unit/oor to top of alcove
Hearth 0" No hearth required
** See mantel clearances chart in this manual.
Flue Clearances to Combustibles
Horizontal - Top 3" (76 mm)
Horizontal - Side 2" (51 mm)
Horizontal - Bottom 2" (51 mm)
Vertical 2" (51 mm)
Passing through wall/
floor/ceiling - when
restop is used.
1-1/2" (38 mm)
Top View
Alcove
H
I
A
E
B
C
G
D
F
D
F
Left Corner
Shown
J
I
A
E
B
C
D
F
When installed as a power vent, the venting
must be reduced to 4" inner x 6-5/8" outer (102
mm x 168 mm) in all applications. See reducers
required in this manual if using rigid/ex pipe.

City Series CB50E | 41
installation
Mantel Clearances
Combustible mantel clearances from top of front facing are shown in the diagram on the right.
Mantel Leg Clearances (Non Glass Side When Installed as a Left/Right Corner)
Combustible mantel leg clearances as per diagram:
212 6 4810
0
14
9” (228 mm)
18"
(457 mm)
10
20
26
To p o f
Fireplace
Opening
12" (305mm)
1/2" (13 mm) Drywall, wood, wood panel, etc.
5 1/4" (133 mm)
To Bottom of
Fireplace
Opening
Max. 12" (305 mm)
MANTEL LEG
0"

42 | City Series CB50E
installation
Framing Dimensions - Bay Install
NOTE: Framing may be constructed of combustible material and does not require steel studs.
Framing
Dimensions Description CB50E
A Framing Height 2 x 4: 44-3/4" (1137 mm)
2 x 6: 51-7/8" (1318 mm)
B* Framing Width 60'' (1524 mm)
C* Framing Depth 20-7/16" (519 mm)
D Minimum Height to Combustibles 62 7/8" (1597 mm)
G Vent Centerline Height 45-3/4" (1162 mm)
** Gas Connection Opening Height See gas connection location in this manual
** Gas Connection Height See gas connection location in this manual
** Gas Connection Inset-Centre Opening See gas connection location in this manual
** See manual for alternate Gas/ Electrical connection options
Note: A combined minimum
of 152 square inches of
open area is required for the
convection air outlet to cool the
enclosure. Ensure clearances
for Convection Air Outlets
are met.
See clearances CB50E in this
manual as there are dierent
methods as to how this can
be achieved.
Note: This appliance must be
installed on a solid surface
such as a plywood oor which
must be the full width and
depth of the appliance.
Ensure that the wood base that the appliance will sit on is strong enough to support the full weight of this appliance.
The overall weight of this appliance is 480 pounds (shipping weight).
Note: Unit must be installed onto a
solid backwall - do not install directly
onto studs.
*C
Note: The framing depth does not take into
account drywall/wood or similar materials
against the back wall. The framing depth will
need to change based on the thickness of the
material (example: 20-7/16 framing depth +
1/2 drywall = 20-15/16")
Max 2 x 6
Max 2 x 6
**

City Series CB50E | 43
installation
Framing Dimensions Corner Kit - Corner Install (Right Corner)
NOTE: Framing may be constructed of combustible material and does not require steel studs.
Note: A combined minimum of
152 square inches of open area is
required for the convection air outlet
to cool the enclosure.
Ensure clearances for Convection
Air Outlets are met.
See clearances in this manual as
there are dierent methods as to
how this can be achieved.
Note: This appliance must be in-
stalled on a level and solid surface
such as a plywood oor which must
be the full width and depth of the
appliance.
Framing
Dimensions Description Corner Kit
A Framing Height 2 x 4: 44-3/4" (1137 mm)
2 x 6: 51-7/8" (1318 mm)
B* Framing Width 60'' (1524 mm)
C* Framing Depth 20-7/16" (519 mm)
D Unit Base to Top Enclosure (Min.) 62-7/8" (1597 mm)
G Vent Centerline Height 45-3/4" (1162 mm)
NOTE: Unit cannot be load-bearing. All nishing materials must be supported by the framing.
Max 2 x 6
Max 2 x 6
*
*
Note: Unit must be installed onto a solid back
wall - do not install directly onto studs.
*Note: The framing width (B) and framing depth (C)
does not take into account drywall/wood or
similar materials against the back wall. The
framing width/depth will need to change based
on the thickness of the material
Example B : 71-1/4" framing width + 1/2" drywall
= 71-3/4".
Example C : 20-7/16" framing depth + 1/2"
drywall = 20-15/16".

44 | City Series CB50E
installation
Framing Dimensions Corner Kit - Corner Install (Left Corner)
NOTE: Framing may be constructed of combustible material and does not require steel studs.
Note: A combined minimum of
152 square inches of open area
is required for the convection
air outlet to cool the enclosure.
Ensure clearances for Convection
Air Outlets are met.
See clearances in this manual as
there are dierent methods as to
how this can be achieved.
NOTE: Unit cannot be load-bearing. All nishing materials must be supported by the framing.
Note: This appliance must be
installed on a level and solid surface
such as a plywood oor which must
be the full width and depth of the
appliance.
Framing
Dimensions Description Corner Kit
A Framing Height 2 x 4: 44-3/4" (1137 mm)
2 x 6: 51-7/8" (1318 mm)
B* Framing Width 60'' (1524 mm)
C* Framing Depth 20-7/16" (519 mm)
D Unit Base to Top Enclosure (Min.) 62-7/8" (1597 mm )
G Vent Centerline Height 45-3/4" (1162 mm)
Max 2 x 6
Max 2 x 6
Note: Unit must be installed onto a solid back
wall - do not install directly onto studs.
*Note: The framing width (B) and framing depth (C)
does not take into account drywall/wood or
similar materials against the back wall. The
framing width/depth will need to change based
on the thickness of the material
Example B : 71-1/4" framing width + 1/2" drywall
= 71-3/4".
Example C : 20-7/16" framing depth + 1/2"
drywall = 20-15/16".
*
*

City Series CB50E | 45
installation
Corner Installation Kit (Black) - Assembly Steps
920-175a 09.26.22
CB60E CORNER INSTALLATION KIT (BLACK) - ASSEMBLY STEPS
Inner Firebox Panels Sold Separately Must Purchase Part #686-907
1. Decideonleftorrightinstall.Takeremovabletrimosidetobe
converted. NOTE: There are three trims on one side.
2. Install trim guide for left or right install to the outer side panel.
3. Screwremovabletrimonandbendtabsclosesttothenishingtrim
inwards 90 degrees.
4. Slideoutersidepaneldownontothetwoscrewsinthereboxbody.
Tighten screws with screwdriver.
5. Screw in the three self-tapping screws at the top of the outer side
paneltoattachittotherebox.
6. Unitcanbeplacedinframingandnishingmaterialsaddedatthis
point.
1
CB60E CORNER

46 | City Series CB50E
installation
920-175a 09.26.22
7. Lift the glass stop and open the glass.
9. Installthebackpanelsbyanglingthebottomofeachpaneltowards
thebaseofthereboxandthenpushingthemin.
8. Install lower inner liner panels.
10.Installtheinnerpanelforthecornerconversionbywedgingitinto
the inner lower liner panels. NOTE: The return on the inner panel
should be at the top facing inward, and the gasket is facing
the side glass.
NOTE: The side glass should not be removed.
12. Once the inner side panel is wedged in place, tighten the hanger
screws for the back liner panels.
11.Slidetheinnersidepanelinbywedgingitbetweenthesideglass
and the back liner panels.
2
CB60E CORNER

City Series CB50E | 47
installation
920-175a 09.26.22
13. Close the glass, turn the glass lifters to the up position, and lock all
the upper and lower clamps.
14. Install outer liner panels - there will be two left over.
15. Slide the corner panel up and in to secure it.
16. Slide the corner panel over to the outer side panel until contact with
magnets is made.
17. Install barrier glass as per instructions in the manual.
3
CB60E CORNER

48 | City Series CB50E
installation
Optional Framing Kit
920-718a 09.07.23
1
CITY SERIES
Framing Kit Assembly
CITY 50 FRAMING KIT ASSEMBLY
PARTS REQUIRED FOR THE FRAMING KIT:
Parts required for the framing kit:
5/16
71 ”
57-1/4"
62"
20-1/2"
62"
Additional wall studs required
57-1/4" center to center
60''
PROCESS :
DWN:
SIGN:
E.C.N.:
DATE:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
PART :
MAT'L :
UNITS IN INCHES
DIMENSIONS
0.000 =
0.01 CRITICAL
0.000
= SPECIFIED TOLERANCE
0.000 = 0.031
0.000 REF = REFERENCE ONLY
ANGULAR = 1
TOLERANCES UNLESS
OTHERWISE STATED
DO NOT SCALE
DRAWING
3RD ANGLE
PROJECTION
REV: PART NO:
FIREPLACE PRODUCTS
INTERNATIONAL
482-900
vkrishnamurthy
-
CB40 Framing Kit Assemby
-
SHEAR/ PUNCH/ FORM
8/1/2023
DATE:
SCALE:
1:16
H
H
B
B
1. Screw the back horizontal and vertical pieces together rst.
Tool/hardware required:
- Level
- Stud Finder
- Cordless Screwdriver
- Phillips Bit
- 5/16 inch hex head bit
- 2" to 3" wood screws (minimum 16)
- Flashlight
Note: Extra screws are provided to assemble this kit.

City Series CB50E | 49
installation
920-718a 09.07.23
2
CITY SERIES
PROCESS :
DWN:
SIGN:
E.C.N.:
DATE:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
PART :
MAT'L :
UNITS IN INCHES
DIMENSIONS
0.000 =
0.01 CRITICAL
0.000
= SPECIFIED TOLERANCE
0.000 = 0.031
0.000 REF = REFERENCE ONLY
ANGULAR = 1
TOLERANCES UNLESS
OTHERWISE STATED
DO NOT SCALE
DRAWING
3RD ANGLE
PROJECTION
REV: PART NO:
FIREPLACE PRODUCTS
INTERNATIONAL
482-502
-
CITY 48 BAY ASSEMBLY
-
SHEAR/ PUNCH/ FORM
9/1/2023
DATE:
SCALE:
1:24
I
I
PROCESS :
DWN:
SIGN:
E.C.N.:
DATE:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
PART :
MAT'L :
UNITS IN INCHES
DIMENSIONS
0.000 =
0.01 CRITICAL
0.000
= SPECIFIED TOLERANCE
0.000 = 0.031
0.000 REF = REFERENCE ONLY
ANGULAR =
1
TOLERANCES UNLESS
OTHERWISE STATED
DO NOT SCALE
DRAWING
3RD ANGLE
PROJECTION
REV: PART NO:
FIREPLACE PRODUCTS
INTERNATIONAL
482-502
vkrishnamurthy
-
CITY 48 BAY ASSEMBLY
-
SHEAR/ PUNCH/ FORM
8/1/2023
DATE:
SCALE:
1:24
J
J
J
J
2. Install the frame assembled in Step 1, onto the back of the unit as
shown with 2 screws on each side.
6. Attach the 2 center supports (Part I) to upper- and lower-part B of
the back frame with 2 screws each as shown.
7. Attach the 4 x end pieces (Part J) to the upper- and lower-Part B of
the back frame with two screws each.
PROCESS :
DWN:
SIGN:
E.C.N.:
DATE:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
PART :
MAT'L :
UNITS IN INCHES
DIMENSIONS
0.000 =
0.01 CRITICAL
0.000
= SPECIFIED TOLERANCE
0.000 = 0.031
0.000 REF = REFERENCE ONLY
ANGULAR = 1
TOLERANCES UNLESS
OTHERWISE STATED
DO NOT SCALE
DRAWING
3RD ANGLE
PROJECTION
REV: PART NO:
FIREPLACE PRODUCTS
INTERNATIONAL
482-502
vkrishnamurthy
-
CITY 48 BAY ASSEMBLY
-
SHEAR/ PUNCH/ FORM
8/1/2023
DATE:
SCALE:
1:24
57 1/4"
PROCESS :
DWN:
SIGN:
E.C.N.:
DATE:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
PART :
MAT'L :
UNITS IN INCHES
DIMENSIONS
0.000 =
0.01 CRITICAL
0.000
= SPECIFIED TOLERANCE
0.000 = 0.031
0.000 REF = REFERENCE ONLY
ANGULAR = 1
TOLERANCES UNLESS
OTHERWISE STATED
DO NOT SCALE
DRAWING
3RD ANGLE
PROJECTION
REV: PART NO:
FIREPLACE PRODUCTS
INTERNATIONAL
482-502
vkrishnamurthy
-
CITY 48 BAY ASSEMBLY
-
SHEAR/ PUNCH/ FORM
8/1/2023
DATE:
SCALE:
1:24
3. Place unit against wall in desired location. Level the unit by adjusting
4 leveling bolts on unit.
4. Install venting before proceeding further with framing kit construction.
Refer to manual for venting instructions.
5. Secure the unit with framing to the wall studs with 2-1/2”-3” wood
screws (not supplied). Use 8 screws and secure to 4 studs minimum.
Ensure the frame is also secured to the 2 additional studs spaced 57-1/4”
apart center to center, using the last hole on the upper- and lower-part
B framing part as shown below.