Regula 70 4m-5a series User manual

DOCUMENT READER

REGULA 70Х4M.ХХХ-5А

User’s Guide

2019

Certi ed Quality

Management System

FCC/Canada Radio Frequency Rules and Regulations

FCC Labeling for USA

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are esigned to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one

or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

FCC ID: 2AOFE-7024M5A

ISED Labeling for Canada

This device contains license-exempt transmitter(s) / receiver(s)

that comply with Innovation, Science and Economic Development

Canada’s license-exempt RSS(s). Operation is subject to the following

two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference

that may cause undesired operation of the device.

IC code: 25676-70X4M5A

L’émetteur/récepteur exempt de licence contenu dans

le présent appareil est conforme aux CNR d’Innovation, Sciences et

Développement économique Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes:

(1) L’appareil ne doit pas produire de brouillage;

(2) L’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

Statement of compliance with safety standards:

The device complies with safety standards listed below:

IEC/EN/UL 62368-1, CSA 22.2. No 62368, IEC 62471, IEC 62479

min 20 см

OPERATING RESTRICTIONS

1. ATTENTION! CONSULT THIS USER’S GUIDE AT ALL STAGES

OF DEVICE OPERATION.

2. When operating the device, do not remove any seals set by

the manufacturer during the whole warranty period.

3. DO NOT SWITCH ON THE DEVICE IN CASE OF ITS MALFUNCTION!

4. DO NOT PLACE ANY FOREIGN OBJECTS ON THE OBJECT GLASS

OF THE DEVICE!

5. DO NOT USE THE DEVICE WHEN THE USB CABLE IS DAMAGED!

6. DO NOT DISMANTLE THE DEVICE AND ELIMINATE ANY

MALFUNCTIONS OCCURRED DURING DEVICE OPERATION WITHOUT

QUALIFIED ASSISTANCE.

7. Do not operate the reader if the object glass is dirty

(see paragraph 3.3 of this User’s Guide).

8. DO NOT OPERATE THE DEVICE AT A DISTANCE CLOSER

THAN 20 CM TO OTHER RADIO-TAIL DEVICES INCLUDING SIMILAR

DEVICES.

This symbol means the product must not be as

household waste, and should be delivered to an

appreciate collection facility for recycling. For more

information on disposal and recycling of this product,

contact your local municipality service, or the shop

where you bought this product.

9. Changes or modi cations not expressly approved by Regula

Baltija, LTD could void the user’s authority to operate the equipment.

CONTENTS

LIST OF ABBREVIATION ..............................6

1 DESCRIPTION AND OPERATION ...................... 11

1.1 Device Function ............................. 11

1.2 Technical Characteristics ....................... 11

1.3 Delivery Set ................................ 12

1.4 Conguration and Operation ..................... 13

1.5 Marking and Sealing .......................... 15

1.6 Packaging ................................. 15

2 INTENDED USE ................................. 16

2.1 Operating Restrictions ......................... 16

2.2 Preparing the Device for Use .................... 16

2.3 Device Use ................................. 18

3 TECHNICAL MAINTENANCE ......................... 20

4 SHIPPING, STORAGE AND UTILIZATION ................ 22

4.1 Shipping .................................. 22

4.2 Storage ................................... 22

4.3 Recycling .................................. 22

5 MANUFACTURER’S WARRANTY ....................... 23

6 ACCEPTANCE CERTIFICATE ......................... 23

APPENDIX A. Device Calibration ....................... 24

APPENDIX B. Drivers Installation ...................... 26

APPENDIX C. Cover Replacement ...................... 27

APPENDIX D. Downloading Regula Document Reader SDK ..... 29

APPENDIX E. Simplied EU Declaration of Conformity ........ 30

User’s Guide Document Reader Regula 70X4M.XXX

LIST OF ABBREVIATION

SDK –Software Development Kit

DR SDK –Document Reader SDK

USB –Universal Serial Bus

OCR –Optical Character Recognition

MRZ –Machine Readable Zone

VIZ –Visual Inspection Zone

ISO –International Organization for Standardization

PPI –Pixels per inch – Image resolution

FDS –Frontline Document System is a reference database,

which contains pattern images of passports,

identity and travel documents, driver’s licenses and

vehicle documents, as well as the data on the basic

authenticity features of passports, IDs and travel

documents, driver’s licenses and vehicle documents

at ve levels of protection: printing design, ultraviolet

365 nm and 254 nm, infrared and special materials

PC/SC –Personal Computer Smart Card Interface

ISO 7816 –ISO 7816-1,-2,-3,-4 Standards for ICC (Smart Cards)

User’s Guide Document Reader Regula 70X4M.XXX

This User’s Guide (hereinafter referred to as the “Guide”) applies

to Regula 70X4M.XXX-5A Document Readers (hereinafter referred to

as the “Device”) intended for capturing full-page document images

under white, infrared, ultraviolet and coaxial white light schemes,

The documents must meet ISO 7810 standard and be either of ID-1, ID-2

or ID-3 sizes

as well as for reading the text (OCR), graphic and biometric

information from the document,

For documents with RFID-tags executed under ISO 14443A standard

or for documents (Smart-cards) executed under ISO 7816 Smart Card

Standard

verifying its authenticity features and transferring the obtained data

to the user application.

The Document Reader “Regula 70X4M.XXX-5A” can be produced in

one of the Modications shown in table 1. The type of the modication

is to be discussed with the Customer when preparing the sales

agreement.

Table 1

Parametres

Device

modications

White

light

870 nm

365 nm

White

coaxial

RFID

reader

Smart-

card

reader

7004M.100-5A • •

7004M.110-5A • • •

7004M.111-5A • • • •

7024M.100-5A • • •

7024M.110-5A • • • •

7024M.111-5A • • • • •

7034M.100-5A • • • •

7034M.110-5A • • • • •

7034M.111-5A • • • • • •

This Guide contains the description of the Device structure,

principle of operation, and operating rules.

User’s Guide Document Reader Regula 70X4M.XXX

The device (depending on the modication) along with supplied

software can:

1. capture color images of a document with the resolution of

400 ppi, 470 ppi or 500 ppi under white, ultraviolet and white coaxial

light and grayscale images under infrared light;

Supported graphic format: BMP, JPEG, JPEG-2000, PNG, TIFF

2. OCR of the data from MRZ of the documents under Doc 9303

ICAO and ISO 7501 standards: 2 lines of 44 characters, 2 lines of

36 characters and 3 lines of 30 characters;

3. evaluate MRZ print quality and verify its authenticity under

Doc 9303 ICAO, ISO 7501, ISO 1831, ISO 1073-2 standards;

4. read 1D and 2D barcodes from a document image;

Supported bar-codes types: PDF-417, Codabar, Code 128, Code 39, Code

39 extended, Code 93, EAN-13, EAN-8, Interleaved 2 of 5 (ITF), Standard

2 of 5 (Industrial), Matrix 2 of 5, IATA 2 of 5 (Airline), UPC-A, UPC-E

5. identify the type and nationality of a document;

6. localize the holder’s photo and signature (if any) of a document

for the recognizable by the system types of documents;

7. OCR of the VIZ data from the documents, including non –

ICAO standard documents;

8. read data from an RFID-chip under “Machine Readable Travel

Documents. Technical Report. Logical Data Structure (LDS)” ICAO

specication;

Supported access modes: Direct, ВАС, ЕАС

Identication: Passive and Active

RFID-chip types: ISO 14443 types А and В

Data exchange rate: 106,212,424 or 848 Kbaud (asymmetric rates support)

9. read data from a contact Smart-card (under the control

of Smart-card application);

ISO 7816 compatible, asynchronous (Т0 and Т1) smart cards are supported.

Data exchange rate: from 2 till 500 Kbaud

10. checking automatically the following authenticity parameters

of the documents:

UV-features:

– absence of luminescence of document material

(UV dull paper check):

- Blank Element

- MRZ Element

- Photo Element

User’s Guide Document Reader Regula 70X4M.XXX

– luminescence of UV protection bers;

– luminescence of UV patterns;

– reading-out text luminescing under UV light and its

comparison with the data retrieved from MRZ or VIZ

(OCR Security Text).

IR-features:

– MRZ printing contrast (IR B900 ink)

– photo embedding type;

– visibility or invisibility :

- Blank Element

- Filled-in document data

- Photo

cross-checking of text data obtained from MRZ, VIZ,

barcode, RFID-chip and Visa;

MRZ check-sums and MRZ completion accuracy;

IPI (invisible personal information) visualization

11. retrieve the specimens images and the description of

a document from FDS information system database for

comparative analysis (comparing with the scanned document);

12. graphic interface Readerdemo.exe: English, Russian, Italian,

Spanish, Lithuanian, Romanian, Arabic, Ukrainian, Latvian, French,

Chinese, Polish.

The device works with the PC under the User application control and

ensures the performance of functions, specied in “Programmer’s

Guide. Document Reader” and “Programmer’s Guide. RFID

Reader”

The User application intended for controlling the device must

be developed on the bases of the libraries from the Software

Development Kits (SDK) under the mentioned Programmer’s

Guides.

Test application Readerdemo.exe (see “Test application

(Readerdemo.exe)”) is an example of the User application designed

for testing the functions DR SDK and RFID SDK (supplied as a part

of the DR SDK).

The user application design and organization of the user application

interaction with the SDK software components are the exclusive

responsibility of the Customer and is not described in this document.

Data reading-out from the contact Smart-cards is performed under

the control of the Application, compatible with EMV CCS requirements

for asynchronous smart cards and is not described in the present

Guide.

User’s Guide Document Reader Regula 70X4M.XXX

PC minimal requirements:

CPU: Intel Core i3 (Intel Core i5)

OS:Windows 7 (Windows 10);

RAM: 4 (8) GB;

Video RAM: 32 (64) MB;

Two USB 2.0 ports;

HDD: 32 (120) GB.

Note:

optionally document reader can work under OS Linux.

The device is powered through the PC USB port.

The time required by the device for document reading and recognition

may vary from 1 to 30 sec. It depends on several factors, such as:

device modication,

software settings concerning reading and authenticity

verication,

availability of RFID chip in a document and RFID chip

characteristics,

PC performance.

ATTENTION!

USE USB CABLE FROM THE DELIVERY SET ONLY

(2 CONNECTORS OF A TYPE AND 1 CONNECTOR OF B TYPE).

Only the user with the administrator’s rights can prepare the PC for

using it along with the device, install the software and test the device.

The customer must follow the safety rules adopted at the user’s

enterprise and the rules of this Guide.

User’s Guide Document Reader Regula 70X4M.XXX

DESCRIPTION AND OPERATION

Device Function

1.1.1 The device designed for capturing full-page document images

under White, Infrared (IR), Ultraviolet (UV) and Coaxial white light

schemes, for reading-out the text (OCR) and visual and biometric

information from the document, as well as for verifying its authenticity

features and transferring the obtained data to the user application.

1.1.2 Protection electric shock of the device corresponds to Class

III by IEC 62368 (the device is protected from voltage or energy

storage dangerous to life).

1.1.3 The device is intended for indoor use under the climatic

conditions as follows:

temperature – -10...+50 °C

relative humidity, max – 95 % (non-condensing)

1.1.4 The device is not intended for use in the re risk and highly

explosive conditions.

1.1.5 The protection class, ensured by the device body, corresponds

to IP50 according to IEC 60529 regulations.

1.1.6 The device is not a measuring tool and is not subject

to metrological testing and certication.

Technical Characteristics

The main technical characteristics are given in Table 2 below:

Table 2

Parameters and Characteristics Parameter or

Characteristic Value

Peak wavelength of the UV-light source, nm 365±3

Peak wavelength of the IR-light source, nm 870±10

Color of the visible light source, including coaxial white (400–650 nm)

Viewing eld, mm, min 128×88

Resolution in the viewing eld 70Х4M.ХХХ-5A, ppi 470 ±5 %

Frame size, Mpixels 5 (2592×1944 pixels)

Operating mode continuous

PC interface USB 2.0

USB-port supply voltage, V 5 ±5 %

USB-port supply current, A, max 0,95

RFID-tag reader parameters:

RFID Frequency band, kHz

Antena max power

13 553–13 567

<60 dΒuΑ/m@10m

1.1

1.2

User’s Guide Document Reader Regula 70X4M.XXX

Parameters and Characteristics Parameter or

Characteristic Value

RFID-tag reader parameters:

Carrier frequency, MHz

Supported standards

Data exchange rate, Kbaud*

13,56

ISO14443 A/B

106, 212, 424, 848,

Smart card reader parameters:

Supported standards:

Data exchange rate, Кbaud

Number of smart cards

Smart cards type

ISO/IEC 7816-1,-2,-3,-4;

EMV2000 4.1, Level 1

2-500

Asynchronous, Т=0 and Т=1

Weight, kg, max

device

device in packing (without a battery pack)

0,82

1,32

Dimensions of tne device (without the cover),

mm, max:

7004М.XXX-5A, 7024М.XXX-5A

7034М.XXX-5A

179×160×99

190×160×99

* – data exchange rate depends on the RFID-chip.

Delivery Set

Table 3

Document reader 1

USB cable 2A-B type*1

User’s Guide 1

Test-object 17.01.05 1

Test-object 17.01.05-01 1

Cover (small) 18.00.01 1

Software and documentation**:

– User’s Guide;

– Document reader SDK;

– Document reader Programmer’s Guide;

– RFID reader SDK;

– RFID reader Programmer’s Guide;

– Test application (Readerdemo.exe) documentation.

Power Adapter/Universal Input: 90~264 V,

50-60 Hz (optional)***

Packaging 18.30.00 1

* – There are three (3) congurations of the cables: 1) 1,5 m (5 ft);

2) 1,8 m (6 ft) and 3) custom cable (specied by a customer).

** – Provided a link to the Internet resource.

*** – Power plug is supplied to be compatible with the standards

of the deployment region.

1.3

User’s Guide Document Reader Regula 70

X4M.XXX

Con guration and Operation

1.4.1 Principle of operation

The device principle of operation is based on the conversion of

document images captured under special lighting conditions into

digital data, reading-out the RFID-tags and Smart-card data and

subsequent data transfer to the PC for further processing.

1.4.2 Device conﬁ guration

The 70X4M.XXX-5A devices have similar form factors.

Modi cations differ in the set of light sources, which can be added

to the white light source (installed in all modi cations), in-camera

resolution (see Table 2), and in availability or absence of built-in units

(see Table 1).

The device ( g.1 and 2) is produced in a plastic body (1). An object

glass (2) protected with a cover (3), a clamp (4) for  xing documents,

and indicator (5) of the device state, and the document processing

results mounted on the top panel of the body (2).

The device has an additional power supply socket (6), a USB input

socket (7), and a HUB USB socket (8) located on the back panel.

Figure 1

1.4

User’s Guide Document Reader Regula 70X4M.XXX

A standard USB cable (for connecting the device to a PC) can be

connected to the socket (7).

ATTENTION!

When using socket 8 it is obligatory to connect an additional

power supply source to socket 6.

The power supply source + 5V, 3A can be delivered by

customer request.

If other power supply sources are used, the Manufacturer

is not responsible for the device safety and operation.

The use of socket 8, when operating the device, may affect

the device.

The RFID reader is inside the device. The read-out area covers

both passport pages.

A smart-card reader (9) located on the back panel of the device

body ( g.2).

1.4.3 Device Operation

Operating modes (illumination) of indicator (5) are set by User’s

application (see Programmer’s Guide DR SDK, chapter 6.8).

The device works with the PC in two modes:

standby mode;

scanning mode.

Figure 2

User’s Guide Document Reader Regula 70X4M.XXX

After the device is connected to the PC, indicator (5) g. 1 will

come on Yellow or Orange (provided that the device driver is already

installed; see paragraphs 2.2.3.1 and 2.2.3.2).

After the device and the SDK software is initialized

(see paragraph 2.2.3.3), the device will switch to the standby mode,

and indicator (5) g. 1 will come on Green. When putting the examined

document (up to the stop to the left and back panels) on object-

plate (2) g. 1, the document edge overlaps photoelectric sensor.

A sensor signal goes off, and the device starts scanning that is shown

by indicator (5) g. 1 with Orange or Red. At this stage the device will

capture the document image under specied lighting conditions, read

the RFID tags data and transfer the data to the PC. After that, the data

is processed by the software components DR SDK and depends on

the functions specied by the User’s application (Programmer’s Manual

for DR SDK, paragraph 6). When the document processing nished,

the device switches to the standby mode, and indicator (5) g. 1

changes to Red or Green depending on the reading/scanning results.

The scanning mode can be also initialized by the user application

command.

Data reading-out from the smart-cards is performed to

the corresponding application after the smart-card is inserted up to

the stop into slot (9) of the device (g. 2).

Marking and Sealing

The device marking meets IEC 62368 and contains:

CE marking;

manufacturer’s name and/or trade mark;

manufacturer’s model identication;

manufacturer name and address;

the serial number of the device according to the

manufacturer’s numbering system;

the symbol for nature of supply;

rated power supply voltage, V;

rated current consumption, A;

“Made in Latvia” inscription;

FCC ID number;

IC ID number;

The WEEE symbol.

1.5.2 The seal is located on the bottom of the device.

Packaging

The package ensures device safety during its transportation and

storage.

1.5

1.6

User’s Guide Document Reader Regula 70X4M.XXX

INTENDED USE

Operating Restrictions

2.1.1 The device must be used under the requirements specied

in paragraph 1.1 of this Guide.

2.1.2 DO NOT USE THE DEVICE WITH A USB CABLE, DIFFERENT

FROM THE SUPPLIED.

2.1.3 DO NOT SWITCH ON THE DEVICE IN THE CASE OF MALFUNCTION.

2.1.4 DO NOT DISMANTLE THE DEVICE AND CLEAR DEFECTS

ARISEN DURING ITS USE WITHOUT ASSISTANCE.

2.1.5 Strictly observe the electric and re safety rules when

operating the device.

2.1.6 Do not remove the manufacturer’s seals from the device

parts during the warranty period.

2.1.7 Do not use the device in case it is not calibrated

(see Appendix A), or its object-plate is dirty (paragraph 3 of this Guide).

2.1.8 Do not use the device closer than 20 cm (8 inches) from any

light-emitting devices, including similar devices.

2.1.9 When operating the device, take measures to prevent con-

densation on the object-glass. When placing the device to a room

with a higher temperature, keep it in this room for two-three (2-

3) hours before its operation.

2.1.10 Do not use any additional power supply sources except for

those that are supplied by the manufacturer.

Preparing the Device for Use

2.2.1 Safety measures

Strictly observe the requirements of paragraph 2.1 when preparing

the device for use.

2.2.2 Putting the Device into Operation

1. Open the package, take out the device, and check the device

completeness under paragraph 1.3.

2. Ensure the device has no mechanical damages, and the object-

plate (2) is clean (g. 1).

2.2.3 Preparing the Device for Operation

2.2.3.1 Adjusting the PC for operation with the device:

1) turn on the PC under the manufacturer’s documentation;

2) load the OS and Log in as the PC Administrator;

2.1

2.2

User’s Guide Document Reader Regula 70X4M.XXX

3) make sure the PC hardware and software conguration meets

the requirements specied in the Introduction of this User Guide;

4) install missing software components, if necessary (see Appendix B);

5) Download Regula Document Reader SDK.exe from

the Internet resource (see Appendix D), run the installation le, and

following the instructions of Installation Wizard install the device

software (the device camera driver, Document reader SDK,

RFID reader driver, and RFID SDK).

2.2.3.2 Preparing the Device for use

1. Perform the operations specied in paragraphs 2.2.2 and 2.2.3.1.

2. Connect the device to the PC using the USB cable. Connect

two (2) sockets of A type of the cable from the delivery set to the PC,

then connect the socket of B type of the same cable to the device.

A message on detecting new devices on the USB bus and the Hardware

Installation Wizard window will appear on the PC monitor; the system

will start installing drivers automatically.

3. Wait until the Installation Wizard is nished and make sure

indicator (5) comes on Yellow or Orange, which indicates that

the installation of the device driver is successfully installed to the PC

(Appendix B).

2.2.3.3 Testing the device operation

1. Prepare the PC and the device for operation under the instructions

specied in paragraphs 2.2.3.1 and 2.2.3.2.

2. Start Readerdemo.exe application using the shortcut on

the desktop;

All operations with the Test Application must be performed under

the instructions specied in the “Test Application (Readerdemo.exe)”

documentation (see Document Reader SDK\Doc\Test Application (en).pdf

in the SDK installation folder – by default C:\Program Files\Regula);

3. Initialize the device and make sure that in 10-15 seconds,

indicator (5) colors will change to Green, indicating that the initialization

is successfully completed.

CAUTION:

During device initialization Readerdemo.exe checks

conformit y of the device rmware version and Document

Reader SDK version . If necessary Readerdemo.exe offers

to update device rmware.

4. Scan the document. Place the document on object-plate (2)

g. 1 up to the stop to the left and back panels. The device will switch

to the reading mode for 1-3 seconds, and the document image will be

displayed in the application window.

User’s Guide Document Reader Regula 70X4M.XXX

The data from the Smart-Card embedded in the document will

be read automatically if the corresponding applications of the Test

application Readerdemo.exe are selected.

5. In case the color rendering is distorted, calibrate the PC display

chromaticity under the manufacturer’s instructions.

Device Use

2.3.1 The device must be controlled by the Test application

Readerdemo.exe or by the User application developed on the basis

of the Document reader SDK libraries according to the instructions

of the Programmer’s Guide (see Doc\Programmer’s Guide

(en).pdf in the SDK installation folder) and the RFID reader SDK

according to the instructions of the Programmer’s Guide (see Doc\

Programmer’s Guide (en).pdf in the SDK installation folder).

2.3.2 The customer is responsible for developing the user application

and ensuring its interaction with DR SDK and RFID SDK2.software

components.

2.3.3 Order of the Device Use

1. Start the PC and the device for operation under the instructions

specied in paragraphs 2.2.3.1 and 2.2.3.2. If operating the device at

the temperature lower than +5 C°, to avoid condensate precipitation

on the device object-glass the PC must provide continuous supply for

its USB-ports (“Green USB” mode must be deactivated).

2. Load the user application and initialize the device. Calibrate

the device, if necessary.

3. Select the scanning mode: automatic (the scanning cycle starts

automatically when the document overlaps photoelectric sensor) or

manual (the scanning cycle begins on the user application command).

4. Set necessary scanning modes.

5. Read the document information by placing the document

on object-plate (2) g. 1 up to the stop to the left and back panels.

CAUTION:

ENSURE A STATIONARY POSITION OF THE DOCUMENT

ON THE DEVICE OBJECT-PLATE DURING THE WHOLE

SCANNING CYCLE, I.E. WHILE INDICATOR 5 (FIG. 1)

IS FLASHING OR -ANGE OR RED.

6. To read the data from the smart-card do the following:

run the corresponding application;

insert the smart-card up to the stop into slot (9) with

contact spaces turned to the device (g. 2);

2.3

User’s Guide Document Reader Regula 70X4M.XXX

perform the actions specied in the corresponding

application.

2.3.4 Finishing the Device Operation

1) Close the user application;

2) Turn off the PC or disconnect the device from the PC, if necessary.

User’s Guide Document Reader Regula 70X4M.XXX

TECHNICAL MAINTENANCE

3.1 Technical maintenance and repairs of the device

must be carried out by the manufacturer’s specialists or

the authorized organizations.

3.2 DO NOT DISMANTLE THE DEVICE OR CLEAR THE DEFECTS

ARISEN DURING ITS USE WITHOUT ASSISTANCE.

3.3 Maintenance

3.3.1 The owner is responsible for device maintenance.

3.3.2 At least once per day (or as far as the object-plate needs

cleaning) the owner must wipe the external surface of the device

body with a soft cleaning cloth moistened with alcohol or special

tissue paper for cleaning PC monitors;

3.3.3 Maintenance: Remove dust and dirt from the external

surface of the body and object-plate with sprays of compressed air

for optical devices (Defender CLN 30802, Fellows FS-99795, FIS

F-1007S MICRO DUSTER , etc.), as well as with a soft cloth (that

does not leave uff) moistened in alcohol or with specialized tissues

for screen cleaning (wet or dry).

3.3.4 Do not wipe plastic parts with acetone or other solvents not

mentioned in paragraphs 3.3.3 and 3.3.4.

3.4 Device Calibration

3.4.1 The device does not require calibration as it is calibrated

by the manufacturer. The calibration data is stored in the NVRAM of

the device.

3.4.2 It is recommended to calibrate the device at least once

per 6 months (see Appendix A) to compensate for possible changes

in light conditions when scanning the documents.

Signs of failure Possible reason Repairing methods

1. When initializing

the device, the message

“Remove the document”

appears on the PC screen

Failure of the sensor of

document presence

Remove the document,

if it is on the desktop

Remove dust and dirt

from the object-plate

surface and particularly

in the zone of the sensor

of document presence

(paragraph 3.3)

If serviceability is not

restored, switch on

the document video

detection mode.

This manual suits for next models

Table of contents

REGULA 70 4M-5A Series User manual

Popular Document Camera manuals by other brands